All posts by Thomas Witherspoon

Field Reports, Morse Code, News, POTA, QRP, QRP Radios

POTA Field Report: A Tale Of Two Parks (And Two Antennas)

8 Comments

Yesterday, I *finally* activated two parks that have been on my list for most of the year: Elk Knob State Game Land (K-6903) and Elk Knob State Park (K-2728).

The game land had never been activated which I found quite puzzling since it seemed to be accessible based on my maps and was only 1.5 miles from (actually adjoining!) a state park which has been activated a number times.

Turns out, there’s a good reason it hadn’t been activated.

Elk Knob State Game Land (K-6903)

Upon entering the game land parcel, you’re greeted by the sign above which states that while the game land is a public resource, it is private land and the owner only allows hunting and trapping on it. First time I’ve ever encountered this.

This meant that I really couldn’t cross the barb wire fence that lined the one lane dirt road to activate the park in the woods (which I would have preferred).

Fortunately, I found one pull-off in the middle of the game land road. It was just wide enough to fit my car so that others on the road could pass me without a problem. It was rather tight, though.

Since I didn’t want to use a tree on the game land to support my antenna, I employed the Chameleon CHA MPAS Lite 17′ vertical.

I pushed the MPAS Lite spike into the ditch of the road and ran the counterpoise along the ditch as well. All was within the road right-of-way, yet within the game land so I felt it a proper compromise respecting the land owner’s wishes while still being able to activate the park.

Gear:

For this activation, I chose the Elecraft KX2 since I had such a limited space in the back of my car to both operate the transceiver and log.

The great thing about the KX2 is it’s such a complete & compact package: it’s a transceiver, with an internal battery pack (that allows 10 watts of power), a built-in ATU, and attachable paddles. Everything easily fits on my clip board which then functions as an operating table.

I started calling CQ POTA and was quickly spotted to the POTA spots page via the Reverse Beacon Network (RBN).

I very quickly logged a number of stations in CW, but did eventually reach one road block when one of the contact posts in my KXPD paddles loosened. I’ve had this happen before. Thankfully, I keep precision screwdrivers in my EDC bag, so could make the fix. Unfortunately, it took me off the air for a good 5-10 minutes and I lost my pile-up.

I eventually changed modes and called CQ a few times on 40 meters phone.

In the end, I only logged 13 contacts. Certainly the smallest number I’ve ever had at an ATNO (All Time New One). I felt I had to cut it short, though, as cars/trucks had to slow down to pass me. Twice I was asked if I needed any help (assuming my car had broken down).

I was very grateful to have the CHA MPAS Lite antenna in my arsenal, though. I have few other antenna options that would have worked so effectively in such a tight space.

The MPAS Lite is also incredibly stealthy. I’m not sure many passersby even noticed it.

On to the next park!

Elk Knob State Park (K-2728)

Where Elk Knob Game Land was an incredibly challenging site, adjoining Elk Knob State Park was the complete opposite. A POTA activator’s dream site.

Gear:

This was my first visit to Elk Knob State Park and I was most impressed. Not only is the park gorgeous and quiet, but the picnic area is expansive, well-spaced, and there are numerous large, old-growth trees. Absolutely perfect for POTA purposes.

The CHA Emcomm III Portable

Since I had the luxury of these tall trees, I decided to employ the CHA Emcomm III Portable which has quickly become my favorite field antenna. When I have the space, I use it because it gives me 160-6 meters and is easily matched by all of my antenna tuners.

Since I had a great picnic table surface to operate, I also used my Icom IC-705 transceiver and Elecraft T1 antenna tuner.

So turns out, I didn’t take a lot of photos of my site because I used my iPhone to make a video of the activation.

On YouTube, I’ve been encouraged by viewers/followers to continue making real-time, real-life videos of some of my park activations. These videos have no edits and are what I would generously call “Ham Radio Slow TV.” 🙂 The idea is the viewer is simply joining me as I set up and operate at a park–as if they were there with me in person. I hope there’s some value in these videos for newcomers to Parks On The Air.

The video ended up capturing the whole activation from start to finish. If you need something to put you to sleep, check it out:

 

Video

All in all, it was a brilliant day and I’m pleased to have finally activated these two POTA sites.

It was a particular treat to discover Elk Knob State Park. I can’t wait to go back there to camp and to hike their trails.

Perhaps this is one of my favorite side benefits of Parks On The Air: it gives me a reason to explore state parks I might have otherwise overlooked. We’re huge supporter of state and national parks, so it’s truly a win-win!

Field Reports, News, Portable, POTA, QRP

Yaesu FT-817: Getting reacquainted with an old friend

8 Comments

In a previous post, I mentioned that I had regretted selling quite a few radios.

Almost immediately after publishing that post, I purchased an Elecraft KX1. It was an impulse purchase, and I’m happy I made it.

Then, a couple weeks ago, my buddy Don discovered I was considering purchasing the Yaesu FT-818.

He mentioned that he had a very lightly used FT-817ND with a lot of extras he would appreciate selling me. I agreed without hesitation.

The package included:

  • Yaesu FT-817ND
  • Inrad SSB 2.0 kHz narrow filter
  • Massoft Mylar speaker (installed)
  • Anderson Powerpole adapter on rear of chassis
  • Yaesu PA – 48B Charger
  • Portable Zero FT-817 ESCORT bracket and side rails in black
  • Portable Zero Sherpa Backpack
  • Nifty Mini Manual
  • Yaesu FNB 85 1400ma
  • All original accessories and antennas

Don offered a fair price for the package, so how could I resist? (Hint: Don’t answer that!)

Besides completely trusting Don as a seller, I must admit that the FT-817 Escort side rails were a big selling point. I’d planned to purchase those regardless. Having owned the original FT-817–what, 20 years ago?–I knew I wanted something to protect this radio in the field. Not only that, but the FT-817 needs a proper bail in my opinion and the Escort delivers!

Blue Ridge National Parkway (K-3378)

Saturday, I had one goal in mind: split some firewood at my father-in-law’s house. But I had to pass the Blue Ridge Parkway (K-3378) en route, so why not a quick activation too, right–?

Gear:

Packed the FT-817ND and, since I needed to fit in a quick deployment, the CHA MPAS Lite antenna.

Talk about getting reacquainted with an old friend: I haven’t operated an FT-817 in at least 18 years!

I was on the air perhaps 35 minutes or so. It was a lot of fun and some trial by fire as I quickly sorted out my CW and phone settings live on the air.

I very quickly made contact with my buddy Eric (WD8RIF) in a park to park contact (thanks, Eric!).

After that, a CW contest started up and I quickly realized how important it will be for me to get a narrow CW filter for the FT-817ND. It was as if 10 stations were sharing the frequency with me. (Any advice on filters would be much appreciated!)

I only managed to collected the 10 contacts needed for a valid activation and, for the first time, relied on my daughters (both licensed) to help snag my 10.

Propagation was poor on Saturday. Since I was in a hurry to get the wood split–and was running behind–I didn’t hang around to work more than 10 stations. Plus, no one “needs” the Blue Ridge Parkway these days since it’s activated so frequently.

This activation was a brilliant shake-out for the FT-817ND field kit. I created a few to-do items:

  • Perform some TX audio tests and tweak the mic settings at home–I feel like the mic gain might have been a bit low.
  • Sort out the AGC and sidetone settings in CW and decide if I want to run full or semi break-in. Between the relay clicks, AGC recovery and gain settings, I found full break-in a little distracting with the lower sidetone volume I had set Saturday. This can be easily adjusted and then it’ll sound great.
  • Dedicate a small external battery pack for the FT-817ND kit. I might purchase another 6aH Bioenno pack especially since it fits in the Sherpa pack side pocket so well.
  • I have the accompanying internal battery pack, but have yet determined how much capacity it still has.

I’m so happy the ‘817ND has re-joined my field radio family! I’ve missed this fine little rig!

Field Reports, News, QRP

Can you activate a park with the Elecraft AX1 portable vertical antenna–?

12 Comments

In my head, this was going to be a post talking about antenna compromise vs. convenience vs. performance. I set out to make a point and will do just that. But it’s not the point I intended to make.

The Elecraft AX1 Antenna

My Maxpedition Fatty Pouch has more than enough room for the AX1, tripod adapter, bipod, antenna, 40M section, and two counterpoises.

For those of you not familiar, Elecraft designed a super compact portable antenna for the KX3 and KX2 called the AX1 a couple years ago. It’s, by far, the most compact HF antenna I’ve ever owned or operated.

What makes it so unique is that no one section of it is longer than 6″, which means when disassembled, it’ll fit in a very small pouch or pocket.

I purchased the AX1 a couple months ago. I bought the antenna, (which handles 20/17 and 15 meters), the 40 meter extension, bipod, tripod mount, and both counterpoises were included.

It’s a cool piece of antenna kit for sure! And so compact!

But let’s face it: it’s a compromised antenna!

An antenna this small and compact is not as efficient as a longer resonant wire antenna. Not even close.

The AX1 wasn’t built for performance per se–although it’s as efficient as it can be for the size–it was built for convenience!

You can set the AX1 up anywhere, anytime.

A POTA Experiment

The AX1 is in the Maxpedition pack on the left, my KX2 in the Lowe pack on the right.

A few months ago, a reader who owns a KX3 asked me if I thought he could successfully activate a (Parks On The Air) park with the AX1.

My reply:

“Sure! Especially if you’re using CW and you have a whole lot of patience.”

Yesterday morning, I decided to test my theory.

I drove to the Blue Ridge Parkway (K-3378) and parked at the Folk Arts Center. I found a picnic table (wasn’t hard at all considering it was hovering around freezing and incredibly breezy!) and set up my station.

It takes me maybe 3 minutes to set up the entire station.

The antenna fits together quickly (I was operating 40 meters, so used the optional extension and 31′ counterpoise).

Three minutes later, I’m ready to rock and roll!

On The Air

I had errands to run in town so didn’t want to spend all day doing this experiment, but I was determined to complete a valid POTA activation which requires 10 total contacts.

Before leaving the house, I scheduled my activation on the POTA site, so it would know to scrape my spot on the Reverse Beacon Network.

Keep in mind, this was taking place on a Monday morning around 10:15 AM and I was activating a park almost every POTA hunter has logged numerous times. The Blue Ridge Parkway is one of the most activated parks in the POTA network, so not exactly super desirable.

In addition, propagation number were pretty dismal.

I fired up the KX2, pressed the ATU button, and achieved a 1:1.1 match.

I called CQ POTA three times in CW.

Evidently, the RBN picked me up quickly, because I received a call.

Then another call.

Then a small pile-up of calls.

Next thing I know, I’ve logged five stations in five minutes.

I called CW again, and had another small pileup.

Short story short, I had achieve a valid activation in all of 12 minutes.

12 freaking minutes!

Seriously? My point was to prove it takes patience when using extremely compromised antennas.

After logging 12 stations, a received a phone call on my mobile and left the air (no other stations were calling me at that point and, again, this wasn’t a highly desirable or rare park). After my phone call, I decided to pack up and finish my errands in town.

After I returned home, I realized: this was easily my quickest field radio deployment and park activation.

The activation took me a total of 20 minutes: 3 minutes to deploy, 12 minutes on the air, and (generously) four minutes to pack up.

Let’s face it…

The stars were aligned Monday morning.

The AX1 is a compromised antenna but it’s obviously also quite effective.

The irony was en route to the activation, I was listening to the latest episode of Ham Radio Workbench. They were discussing wire antennas and how incredibly compromised shortened verticals are.

I was in complete agreement about compact antennas: sometimes, the compromise is worth it for the convenience.

Now, I would add: sometimes, it’s all convenience, performance, and no compromise whatsoever!

Next, I plan to attempt an SSB activation with the AX1. I do believe it’ll take quite a while to gather 10 stations for a valid activation. But who knows?

Stay tuned!

Antennas, News, Reviews

CHA MPAS Lite: A military-grade compact field antenna

4 Comments

Note: the following post was originally published on the SWLing Post. 

Chameleon Antenna recently sent me a prototype of their latest antenna: the CHA MPAS Lite.

The MPAS Lite is a compact version of their MPAS 2.0 modular antenna system and designed to be even more portable.

Chameleon Antenna is a specialist antenna manufacturer that makes military-grade, field portable antennas that are low-profile and stealthy. Chameleon products are 100% made in the USA and their customers range from amateur radio operators to the armed forces.

Their antennas are not cheap, but they are a prime example when we talk about “you pay for what you get.” In all of my years of evaluating radio products, I’ve never seen better quality field antennas–they’re absolutely top-shelf.

Zeta

I’m currently in my hometown doing a little caregiving for my parents. I’d only planned to be here for a couple of days, but when I saw that the remnants of Hurricane Zeta would pass directly over us with tropical storm force winds and rain, I stuck around to help the folks out.

Zeta struck quite a blow, in fact. No injuries reported, but over 23,000 of us have been without power for over 34+ hours in Catawba county. With saturated grounds, the winds toppled a lot of trees and damaged power lines.

Yesterday, I wanted to take advantage of the power outage and get on the air. I couldn’t really do a POTA activation because I needed to manage things here at my parents’ house. Plus, why not profit from the grid being down and bathe in a noise-free RF space–?

I decided to set it up in their front yard.

CHA MPAS Lite

I had never deployed the MPAS Lite before, so I did a quick scan through the owner’s manual. Although the MPAS Lite (like the MPAS 2.0) can be configured a number of ways, I deployed it as a simple vertical antenna.

Assembly was simple:

  1. Insert the stainless steel spike in the ground,
  2. Attach the counterpoise wire (I unraveled about 25′) to the spike
  3. Screw on the CHA Micro-Hybrid
  4. Screw the 17′ telescoping whip onto the Hybrid-Micro
  5. Extend the whip antenna fully
  6. Connect the supplied coax (with in-line choke) to the Hybrid-Micro
  7. Connect the antenna to the rig

Although I had the Icom IC-705 packed, I wanted to keep things simple by using the Elecraft KX2 I’d also packed since it has a built-in ATU.

Important: the CHA MPAS Lite requires an ATU to get a good match across the bands.

I wasn’t in the mood to ragchew yesterday, but I thought it might be fun to see how easily I could tune the MPAS Lite from 80 meters up.

I checked the Parks On The Air spots page and saw NK8O activating a park in Minnesota in CW:

He was working a bit of a pile-up, but after three calls, he worked me and reported a 559 signal report. Not bad at 5 watts!

I then moved to 40, 18, and 20 meter and called CQ a couple times to see if the Reverse Beacon Network (RBN) could spot me. I like using the RBN to give me a “quick and dirty” signal report. I was very pleased with the bands I tested:

Those dB numbers are quite good for an op running 5 watts into a vertical compromised antenna.

The KX2 very effortlessly got near 1:1 matches on every band I tested.

Of course, after working a few stations in CW and SSB, I tuned to the broadcast bands and enjoyed a little RFI-free SWLing. Noting 13dka’s recent article, I’m thinking on the coast, the MPAS Lite will make for a superb amateur radio and SWLing antenna.

Durability

Although the remnants of Zeta had effectively passed through the area three hours prior, it was still very blustery outside. I was concerned gusts might even be a little too strong for the 17′ whip, but I was wrong. The whip handled the wind gusts with ease and the spike held it in place with no problem.

One of the things I have to watch with my Wolf River Coils TIA vertical is the fact it’s prone to fall in windy conditions and many ops have noted that this can permanently damage the telescoping whip (the weak point in that system).

I’m pretty certain this wouldn’t happen with the Chameleon 17′ whip–it feels very substantial and solid.

Ready to hit the field with the CHA MPAS Lite!

I’m a huge fan of wire antennas because I believe they give me the most “bang-for-buck” in the field, but they’re not always practical to deploy. I like having a good self-supporting antenna option in my tool belt when there are no trees around or when parks don’t allow me to hang antennas in their trees.

I’ve got a park in mind that will make for a good test of the CHA MPAS Lite: it’s a remote game land with no real parking option. I’ll have to activate it on the roadside–an ideal application for the MPAS Lite.

Click here to check out the CHA MPAS Lite.

Field Reports, News, Portable, POTA

POTA Field Report: Finally putting Toxaway State Game Land on the air

1 Comment
The C-Ruck loaded and ready for the field!

I woke up Saturday morning (October 24, 2020) with one goal in mind for that day: activate Toxaway State Game Land (K-6960).

This year, I’ve had a blast finding game lands to activate for the Parks On The Air (POTA) program as they are typically are less crowded, have open areas to hang long antennas, and sometimes even give me a chance to do a little off-roading.

I’ve had Toxaway on my list of game lands to activate since April, but it’s a good 1.5 hour drive from the QTH and not in a part of the state I routinely drive through these days. After some searching, via the excellent WRC interactive map, I was able to find one access point that even appeared to have parking for a trail head.

I checked with the family and they were all up for a  drive and picnic lunch.

It’s still “leaf-looking” season here in the mountains of western North Carolina, so the roads were pretty crowded with tourists.  The closer we got to this relatively remote site, though, the less traffic. A very good sign!

Our location

Gear:

Chameleon Antennas recently sent me their new CHA MPAS Lite vertical to evaluate and I had planned on deploying it for this activation, but once I arrived on site, I realized I should have checked a topo map first: it was deep in a valley near a creek and I questioned the wisdom of using a short vertical in this situation. That and propagation wasn’t exactly stellar.

Fortunately, there were tall trees around, so I deployed the CHA Emcomm III Portable random wire antenna which has become one of my favorite field antennas.

Saturday was also the CQ WW SSB contest, so the phone portions of the bands were very busy with contest activity. I planned to make this primarily a CW activation.

After setting up the Icom IC-705, I attached my Elecraft T1 ATU to the rig and antenna. Since this turned out to be a parking area activation, I could have set up my portable table, but instead, I used the Red Oxx C-Ruck pack to support the IC-705 and ATU.

Using the C-Ruck as a mini field table saves time. I discovered how useful this pack was while evaluating the lab599 Discovery TX-500 in August.

I started calling CQ POTA on 40 meters and within seconds the the POTA site auto-spotted me via the Reverse Beacon Network (RBN). I only called CQ POTA twice before I started working pile-ups.

The Emcomm III Portable antenna performed admirably as I pushed a full 10 watts of power.

Indeed, for me, this activation was a bit of a sprint to answer everyone calling me in the amount of time I had at the site. To make the activation work in our Saturday schedule, I only allowed for one hour on the air.

QSO Map and logs:

Map courtesy of QSOMap.org Green=CW Red=Phone (Click to enlarge)

Not at all bad for 10 watts and a wire!

I could have worked many more stations had I moved to 20 meters CW and then back to 40 meters CW, but I did want to make a few SSB QSOs and even attempt hunting other POTA parks.

Some highlights: working my buddies (and fellow SEORAT members) Eric (WD8RIF) in park-to-park contacts, and Mike (K8RAT) who is one of the top hunters in POTA and also huge support to Eric and me in the field.

I was also very pleased to work another local park activator, Steve (KC5F), who is an excellent CW op–indeed, I believe this was our first SSB contact! Steve primarily operates CW with his Xiegu G90.  We typically struggle working each other because we’re simply too close geographically!

All in all, it was amazing fun!

Once again, I was impressed with the IC-705’s capabilities, the T1’s excellent matching skills, and the Emcomm III portable’s performance.

I also find the CW Morse Pocket Paddle to be a brilliant portable paddle. It’s slightly larger than my N0SA paddles, but still very portable. I’ve been carrying them in the top flap of my ruck sack.

I will plan to return to Toxaway, perhaps this winter, and spend more time at the site.

If you would like to post a field report on QRPer, drop me a line!

Grab And Go, News, Portable, QRP, QRP Radios

The Elecraft KX1: Reunited and it feels so good.

10 Comments
The Elecraft KX1

A few weeks ago, I published a post about radios I’ve regretted selling or giving away.

Number one on that list was the Elecraft KX1.

Within a couple hours of posting that article, I had already purchased a KX1 I found on the QTH.com classifieds. It was, by any definition, an impulse purchase.

The seller, who lives about 2 hours from my QTH, described his KX1 as the full package: a complete 3 band (40/30/20M) KX1 with all of the items needed to get on the air (save batteries) in a Pelican 1060 Micro Case.

The KX1 I owned in the past was a four bander (80/40/30/20M) and I already double checked to make sure Elecraft still had a few of their 80/30 module kits available (they do!).  I do operate 80M in the field on occasion, but I really wanted the 80/30 module to get full use of the expanded HF receiver range which allows me to zero-beat broadcast stations and do a little SWLing while in the field.

The seller shipped the radio that same afternoon and I purchased it for $300 (plus shipping) based purely on his good word.

The KX1 package

I’ll admit, I was a bit nervous: I hadn’t asked all of the typical questions about dents/dings, if it smelled of cigarette smoke, and hadn’t even asked for photos. I just had a feeling it would all be good (but please, never follow my example here–I was drunk with excitement).

Here’s the photo I took after removing the Pelican case from the shipping box and opening it for the first time:

My jaw dropped.

The seller was right: everything I needed (and more!) was in the Pelican case with the KX1. Not only that, everything was labeled. An indication that the previous owner took pride in this little radio.

I don’t think the seller actually put this kit together. He bought it this way two years ago and I don’t think he ever even put it on the air based on his note to me. He sold the KX1 because he wasn’t using it.

I don’t know who the original owner was, but they did a fabulous job not only putting this field kit together, but also soldering/building the KX1. I hope the original owner reads this article sometime and steps forward.

You might note in the photo that there’s even a quick reference sheet, Morse Code reference sheet and QRP calling frequencies list attached to the Pelican’s lid inside. How clever!

I plan to replace the Morse Code sheet with a list of POTA and SOTA park/summit references and re-print the QRP calling frequencies sheet. But other than that, I’m leaving it all as-is. This might be the only time I’ve ever purchased a “package” transceiver and not modified it in some significant way.

Speaking of modifying: that 80/30 meter module? Glad I didn’t purchase one.

After putting the KX1 on a dummy load, I checked each band for output power. Band changes are made on the KX1 by pressing the “Band” button which cycles through the bands one-way. It started on 40 meters, then on to 30 meters, and 20 meters. All tested fine. Then I pressed the band button to return to 40 meters and the KX1 dived down to the 80 meter band!

Turns out, this is a four band KX1! Woo hoo! That saved me from having to purchase the $90 30/80M kit (although admittedly, I was looking forward to building it).

Photos

The only issue with the KX1 was that its paddles would only send “dit dah” from either side. I was able to fix this, though, by disassembling the paddles and fixing a short.

Although I’m currently in the process of testing the Icom IC-705, I’ve taken the KX1 along on a number of my park adventures and switched it out during band changes.

Indeed, my first two contacts were made using some nearly-depleted AA rechargeables on 30 meters: I worked a station in Iowa and one in Kansas with perhaps 1.5 watts of output power.

I’m super pleased to have the KX1 back in my field radio arsenal.

I name radios I plan to keep for the long-haul, so I dubbed this little KX1 “Ruby” after one of my favorite actresses, Barbara Stanwyck.

Look for Ruby and me on the air at a park or summit near you!

Field Reports, How To, Morse Code, News, Portable, POTA, QRP, SSB

Parks On The Air 101: Some real-time, real-life videos of a typical POTA activation using the Icom IC-705

8 Comments

On Monday (October 19, 2020) I received an inquiry from Dale (KI5ARH) only an hour or so before packing up my radio gear to activate Lake Norman State Park (K-2740).

Dale is interested in using his recently acquired Icom IC-705 to get involved with Parks On The Air (POTA) and play radio in the field.

What’s in my field kit

Dale was curious about all of the components of the field kit I use with the IC-705, so I made this video:

Equipment links:

Since I had already set up my phone to record the video above, I decided to make a couple more.

I thought there might be some value in making real-time videos showing what it’s like operating CW and SSB during a POTA activation.  The videos have no edits and haven’t been trimmed.  It’s as if the viewer were there at the activation sitting next to me at the picnic table.

Operating CW with the IC-705

After setting up my station, I first started on the 40M band in CW. I meant to start the camera rolling during tune-up, but forgot to hit record. The video begins after I’d made a few CW contacts, but shows what it’s like changing bands and relying on the Reverse Beacon Network (RBN) to pick me up then the POTA website to auto spot me.

Note: to be automatically spotted by the RBN, you must schedule your activation via the POTA website in advance, or have been already spotted by yourself or someone else, so the system will know to look for you.

My video cut off abruptly due to a low battery message. I had to give my iPhone a quick power charge to make the next video.

Operating SSB with the IC-705

After operating CW for a while, I plugged in the hand mic that ships with the IC-705 for a little SSB action. My main goal with this video was to show how I call CQ and use the voice keyer memories in order to manage the field “work flow” process.  I also speak to how important it is to either self-spot or have a friend spot you to the POTA network while operating phone.

I spent so much time setting up and running the camera, I wasn’t actually on the air for very long, but I easily managed to achieve a valid activation and had a lot of fun in the process.

I’m not a pro “YouTuber” as I say in one of my videos. I much prefer blogging my experiences rather than “vlogging,” I suppose.

Still, I think I’ll do a few more “real-time” videos of POTA activations and speak to the various techniques I use to activate parks. Since these videos aren’t edited for time, they may not appeal to the seasoned POTA activator or QRPer–that’s okay, though. My goal is primarily to assist first-time POTA activators.

Have you been activating Parks or Summits lately?  Do you have any advice or suggestions I failed to mention? Or do you have suggestions for future topics? Please comment!

Field Reports, News, POTA

POTA Field Report: Mount Mitchell State Park (K-2747) with the Mission RGO One transceiver

Leave a comment

On Thursday October 15, 2020, my family made an impromptu trip to Mount Mitchell State Park to enjoy the amazing weather and gorgeous fall colors.

The Blue Ridge Parkway and Mount Mitchell State Park were predictably crowded with tourists, although nowhere near as crowded as the following three days which were “peak” leaf color days.

After arriving at the park, we claimed one of the little picnic areas tucked away from the crowds.  After a picnic lunch, I set up the station, my wife painted, one daughter caught up on her favorite book, and the other daughter took a deep dive in her recently acquired Yaesu FT-60R (and also helped me log).

And Hazel, predictably, slumbered.

I swear that dog is only awake maybe one hour a day.

On this particular activation, I didn’t want to deploy a wire antenna. Being the highest elevation east of the Mississippi river, the trees are short .

Instead, I deployed my Wolf River Coils TIA vertical antenna.


I consider the WRC vertical to be a “compromised” antenna especially in our region which is rocky and has poor ground conductivity. But at times like this when the park is crowded, it’s a great low-profile way to get on the air–and it’s self-supporting!  In any other year, I’m actually okay with my radio set-up being conspicuous–I love telling passersby about ham radio and Parks On The Air–but at the moment I choose to keep my social distance.

When I use the WRC antenna, I typically pair it with one of my favorite transceivers: the Mission RGO One.

I love the Mission RGO One. It’s a superb transceiver (indeed, my full review of it will appear in the November 2020 issue of The Spectrum Monitor magazine).

I like to pair the RGO One with the WRC vertical because the RGO One is capable of 50 watts of output power (the real max for the WRC), which I feel makes up for a bit of the antenna compromise. I typically start at QRP levels and increase wattage if I get no response.

At Mt. Mitchell, I rarely have internet access via my mobile phone, so I rely on the Reverse Beacon Network to spot me to the POTA network when I call “CQ POTA.”

Within a minute of calling CQ, I started logging stations. Thanks RBN!

I operated for almost an hour off and on. I took a few breaks during low activity to help my daughter with the FT-60R. At one point, she was in hysterics over a conversation she picked up on a local repeater. (Hysterics in a good way, fortunately. I do worry about some of the conversations I hear on local repeaters at times!)

Here’s my tally from Mt Mitchell:

Mt. Mitchell is one of our family’s favorite state parks and is accessible from my QTH via the Blue Ridge Parkway.

Unfortunately, the Blue Ridge Parkway is often closed during the winter, so we hope to make at least one more trip to Mitchell within the next few weeks.

I’ll add that this was the third time I’d taken the CW Morse “Pocket Paddle” to the field. It’s a brilliant set of paddles. It’s has a fantastic field-adjustable response. I’m uncertain if they’re on the market yet–CW Morse sent them to me for evaluation in the field.

I also have a set of N0SA paddles I love and typically keep packed in my dedicated MTR-3B pack.

Field Reports, News, Portable, QRP Radios

POTA Field Report: Pairing the Icom IC-705 with the Elecraft T1 and CW Morse Pocket Paddles

8 Comments
The new CW Morse “Pocket Paddle.”

On Wednesday, October, 14 2020, the weather was gorgeous so I decided to make an impromptu POTA activation of Pisgah National Forest and the Pisgah Game Land (K-4510 and K-6937). These sites are the closest to my QTH and only a 15 minute drive (in fact, I can even hike up to the same trail network from my back yard).

My canine companion, Hazel, jumped into the car before I could even invite her to come along.

We drove to the trailhead, parked, and hiked a short distance into one of my favorite spots where it’s relatively flat, with lots of tall trees and almost no foot traffic from other hikers.

This activation gave me an opportunity to use the Icom IC-705 in more of a “backpack” setting since I hiked in with only my pack, Hazel, and my folding three-leg stool. Up to this point, I’d only used the IC-705 on picnic tables and flat surfaces since it can’t easily fit on my clip board like my MTR-3B, KX2, and KX1 can.

The activation also gave me a chance to evaluate a new product sent to me by the CW Morse company: their “Pocket Paddle” designed specifically for portable operations.

After reaching the site, I easily deployed the EFT-MTR antenna using my arborist throw line.

I decided to set up the Icom IC-705 much like I did the lab599 Discover TX-500 when I took it on hikes: mount the radio above the front pocket of my Red Oxx C-Ruck backpack.

The arrangement works quite well–I simply sit on the stool in front of the pack and hold my simple logging notepad and paddles on a clipboard.

While this particular site is great because it’s so accessible to me, the negative is it’s deep down in a valley surrounded by high ridge lines. I feel like this does have some impact on how well my signal travels.

Wednesday, it took nearly 50 minutes to rack up a total of 12 contacts in CW mode.  I never bothered with SSB/phone because this site had no cell phone service and, thus, there was no way to spot myself on the POTA network.

That’s okay, I felt pretty chuffed about racking up 12 contacts with 5 watts and a wire! This is what field radio is all about, in my opinion.

Loving the Elecraft T1

The Elecraft T1 ATU pairs beautifully with the Icom IC-705.

After a little falling out with the mAT-705, I decided I wanted to try other ATUs with the IC-705. I used to own an Elecraft T1 ATU and loved it, but I eventually sold it for a song to a friend since all of my field rigs at that point had internal ATUs.

I reached out to Elecraft and they sent me a T1 on loan to give it a go.  I’d forgotten how much I love this simple, effective ATU.

Even though the EFT-MTR is resonant on 40, 30, and 20 meters, moving to the 30 meter band requires lowering the antenna, pulling off an SMA cap on the coil, then re-hanging it.  Not a big deal at all, really, but it’s so much easier to simply press the tune button on the T1 and have it match 30 meters without going through the normal process.

CW Morse Pocket Paddle

I also thoroughly enjoyed using the CW Morse “Pocket Paddles.” I’m not sure when they’ll be available to purchase (perhaps they are already?) but I can highly recommend them.

The paddle action is field-adjustable and even though there’s an Allen wrench built into the paddle base, the machined screws are easy to twist by hand.

They feel very sturdy, too, much like the other CW Morse paddles and keys I’ve used.

I believe the Pocket Paddles are going to permanently pack with my IC-705!

Field Reports, News, Portable, POTA, QRP Radios

The Icom IC-705 might be a ‘Holy Grail’ portable QRP SSB transceiver

5 Comments

While visiting my parents this week in the Piedmont of North Carolina, I took some time Monday afternoon to take the new Icom IC-705 to field and activate Lake Norman State Park (K-2740) for the Parks On The Air (POTA) program.

So far, most of my time with the IC-705 has been in CW mode but a number of my readers have been asking about SSB operation and performance.

My goal for this park activation was to give the IC-705 a proper shake-out on SSB.

Set-up

The activation was very much impromptu–I only decided I could fit it into my day an hour before my start time. In addition, while it wasn’t raining per se, there was a very heavy mist/fog that, at times, felt like a light sprinkle/drizzle.

I packed and planned on using my IC-705, mAT-705 external ATU, and Vibroplex End-Fedz EFT-MTR wire antenna.

I had an issue with the mAT-705 ATU (read more here), so opted for my trusty and incredibly capable Emtech ZM-2.

I did begin the activation in CW and quickly racked up a dozen or more contacts in short order after spotting myself. One of the great things about Lake Norman State Park is it’s one of the few locations I activate these days with proper cell phone coverage for mobile internet so that I can update my own activation spots on the POTA site.

I also moved up to 20 meters and switched over to my recently (re)acquired Elecraft KX1 (FYI, I named her “Ruby” so no way will I sell her again).

I quickly snagged two states (Iowa and Kansas) with 1 watt of power from the KX1’s internal AA cells, then 20 meters fell silent, so I moved to 30 meters to work a few more stations.

SSB on 40 meters

I then moved to the 40 meter band and decided to record a quick video after spotting myself on 7197 kHz.  I wasn’t expecting such a productive mini pile-up.

As you can tell from the video, I had my hands full trying to hold my phone/camera, log, and manage the hand mic. Note, too, I prefer not hooking up the speaker portion of the microphone because audio from the IC-705 internal speaker is far superior:

I operated SSB for a good 30 or so minutes and was busy with contacts thanks to all of those excellent POTA hunters.

IC-705 Voice Memory Keyer

Before packing up, I remembered that my buddy Dave had asked me to make a video showing how I use the IC-705’s voice memory keyer, so I moved up to 20 meters (which you’ll see was pretty much dead) and recorded this.

Doh! I had the SSB position in LSB instead of USB! Thanks to one of my YouTube viewers who noticed this. I had been tinkering with mode settings earlier while evaluating the rig. No worries, though, this was more a demo of the memory keyer–check out SSB operation in the video above.

I was actually very relieved 20 meters was dead because I’m terrible at managing a camera, a tablet, and a microphone all at once!

The Icom IC-705 is an SSB champ

Photo taken at South Mountain Game Land last week.

Despite the fact that I was using the default microphone settings and had not even touched the TX EQ or compression, I received no less than three unsolicited compliments about my audio during this activation.  That is probably a personal record.

No doubt, the IC-705 is a very capable rig for QRP SSB where audio quality is essential.

On top of that, the eight voice keyer memories are incredibly useful when activating a park, a summit, or even running a contest where you could truly automate your exchanges.

Have you been using the IC-705 in the field? What are your thoughts? Do you have any questions? Please feel free to comment!