Tag Archives: QRP

Field Reports, News, Portable, POTA, QRP

POTA Field Report: Activating Kerr Scott State Game Land with the Elecraft KX2, 5 watts, and a not-so-resonant wire

7 Comments

Some of my most enjoyable field activations are those involving the least amount of equipment and accessories. Maybe it’s my “less is more” mentality, but it is amazing when all I need to get on the air is one radio, a feedline, logging notebook, and a simple antenna.

That was my set-up earlier this week (February 8, 2021) when I activated Kerr Scott State Game Land–a site I hadn’t visited since last summer.

Kerr Scott State Game Land (K-6918)

I was the first person to activate Kerr Scott State Game Land back in June of 2020.

I vividly remember that activation because, as I noted in my field report on the SWLing Post, it was Kerr Scott that taught me an invaluable lesson:

“[I]f you don’t have a “spot” of your activation on the POTA site, it’s like you don’t exist.”

This was truly a tipping point that lead me down the path of doing CW activations in order to benefit from auto-spotting via the Reverse Beacon Network (RBN). Only a couple weeks after this activation, I made my first CW activation and the rest is history. While I still use SSB during activations, CW has become my favorite mode even though I’m still not that great of an operator.

I speak about this a bit more in my activation video below.

Gear:

Once I arrived on site, I deployed my EFT Trail-Friendly 40/20/10 meter end-fed resonant antenna.

The last few times I deployed this antenna in the field, it hasn’t been resonant on 40 meters and I suspect this is due to damage to the coil near the end of the radiator. I decided I’d give it one last test  by suspending it in an overhanging tree branch about 50 feet high so it would not touch other branches.

When I turned on the KX2, I set the internal ATU to “bypass” and tested SWR. Sadly, it was unacceptable, so I re-activated the ATU to get a good match.

My buddy and fellow POTA activator, Steve (KC5F), reminded me recently that the radiator on this antenna can be replaced with enough wire to make a simple end fed half wave. That’s probably what I’ll do because, frankly, this antenna has served me so well for five years and over 150 park activations I’m not ready to simply toss it. I will need to order some proper wire for the EFHW, though!

On The Air

Since I have no mobile phone/Internet service at this site, I decided to make this a CW only activation, hopefully taking full advantage of auto-spotting to the POTA spots page.

I started on 40 meters because I had pre-arranged with my buddies Mike (K8RAT) and Eric (WD8RIF) to listen for me on 7063 kHz. I did this in case auto-spotting wasn’t working, which does happen from time-to-time. It’s always important to have a back-up if possible especially for sites (like this one) that carry significant travel time.

I hopped on 40 meters, called CQ POTA and within 29 minutes, I logged 26 stations. That’s about as much activity as I could possibly expect during a Monday morning activation!

Next, I moved to 20 meters and started calling CQ. The first station I worked was CU3BL in the Azores, then WD5GRW in Texas, AB6QM in California, then IK4IDF in Italy, and finally KH2TJ in California.

I then moved to 30 meters and worked N5GW in Mississippi before going QRT with a total of 32 stations logged.

Not at all bad using 5-10 watts!

Here’s a QSOmap of this activation (click to enlarge):

Activation Video

I made a real-time, real-life, no edit, no advertisements video of this activation. Feel free to check it out if you like:

Click here to view on YouTube.

One of the things I rarely mention in my videos and field reports is how much I love the trips to/from an activation site. I’m a traveler at heart and while I’ve been fortunate enough to travel to and live in some pretty amazing countries and cities, I still have a deep appreciation for simply driving through the countryside and taking in the scenery. I appreciate the mundane as much as I do the majestic. It’s a beautiful drive.

Kerr Scott Game Land is located in the little farming community of Boomer, NC which, I understand, was named after its first postmaster, Ed “Boomer” Matheson.

Warrior Creek, next to my activation site at Kerr Scott

Before it was called Boomer, the community was known as Warrior Creek–the very creek running through Kerr Scott Game Land.

Even though I know there’s no connection, when I hear the name Boomer I can’t help but think of the incredibly cute and cheeky red squirrel that we WNC natives call “Boomers.”

Field Reports, News, Portable, POTA, QRP

POTA Field Report: Activating South Mountains Game Land in gusty winds

6 Comments

Last week, I had a hankering to visit a site I hadn’t activated in a few months: South Mountains Game Land.

This game land is pretty vast and has a number of entry points, almost all of which are very accessible. When I re-visit a site multiple times, I like to try different entrances when I can because it gives me a chance to check out a site better and, frankly, even enjoy a little light off-roading.

I found a western road leading deep into South Mountains from the Wildlife Resource Commission map and decided to explore it and do a quick activation.

South Mountains Game Land (K-6952)

I avoid activating Game Lands on days when I suspect there will be a lot of hunting. Tuesday afternoon was *not* ideal for hunters. Besides being the middle of a work day, it was cold and very gusty.

As I drove about 4 miles into the site, I didn’t see a single car or truck parked in any of the parking areas. I could tell I had the place to myself.

A Few Precautions

It goes without saying that if you’re doing a POTA or SOTA activation in a rural/remote area that has no mobile phone coverage (quite common at the ones I activate), you really need to take a few precautions.

First of all, let someone else know where you’ll be and how long you plan to be there.  I always let a couple radio friends know where I’ll be so if I don’t show up on the air or they don’t hear from me, they could contact authorities to look for me.

Secondly, always take a proper first aid kit. If you get hurt, you need a way to apply first aid until you can get help.

Take a handheld radio with local repeater frequencies pre-loaded. Even though I might not have cell phone coverage, I can almost always hit at least one repeater.

Of course, carry a little food and water with you and make sure your vehicle has fuel as well.

Always wear a high-visibility vest, jacket, and/or cap. Many game lands require these. Besides, would you rather perform and activation or get shot? I don’t like getting shot. I also don’t like the idea of being bear food, so at least pack a little bear mace if you’re in bear country.

When I’m activating a game land I don’t hike deep into the woods. In fact, I try to stay on or very close to a parking area. Even though POTA is becoming a very popular radio activity, I can promise that you’ll likely be the first POTA activator most hunters will see. It’s a good idea to be near areas of activity like a parking spot or road where they’re much less likely to be hunting.

Finally, as I mentioned before, I personally do not activate game lands on busy hunting days.

Of course, check the weather forecast in advance.

On The Air

I found a great spot to set up my station near a ridge line deep in the game lands.

Normally, I’d set up right next to my car, but Tuesday the winds were very gusty so I found a semi-protected area maybe 10 yards off the road. I located a spot with the least amount of overhanging branches (always check for widowmakers and dead trees!).

Gear:

It only took me five minutes to deploy the Chameleon Emcomm III Portable random wire antenna with my arborist throw line.

Random wire antennas require tuners, so I employed the Mat-Tuner mAT-705 Plus.

This site has no mobile phone coverage, so I had no easy way to spot myself to the POTA spots page had I decided to do a little phone/SSB operating. I decided to stick with CW as the POTA spots page will auto-spot me using my information from the Reverse Beacon Network (as long as that system is working).

It’s so rare that I do activations around noon or early in the afternoon, so I decided to start on 20 meters just to see if I could snag a European station.

I felt pretty chuffed to quickly snag the Azores (CU3BL) and a few west coast stations with my 5 watts and a wire. QRP rocks!

I then moved to 40 meters where I worked a number of stations in succession and topped off the activation with one 30 meter contact.

Here’s a QSOmap of this activation:

Not bad for about 40 minutes on the air.

Video

I also made one of my real-time, real-life videos of the activation. Note that my camera died on me perhaps five minutes before I completed the activation, so it will end abruptly. Sorry about that!

My ankle is healing nicely so I’m feeling more comfortable with the idea of hiking again. I’m plotting a SOTA activation with my daughter in the coming weeks.

Events, QRP

Are you ready to FYBO?

8 Comments
(Photo credit: K4TLI)

Here in portions of North America, we’ve been receiving some seriously cold and snowy weather the past week. It’s the sort of weather that encourages one to conjure up images of warm slippers, sitting by the fire, reading a book, and drinking hot chocolate.

Or, you can choose to Freeze Your B___ Off!

Against my better judgement, that’s exactly what I plan to do tomorrow.

My buddy Eric (WD8RIF) reminds me that tomorrow (Saturday, February 6, 2021) is FYBO: a long-standing winter QRP contest sponsored by the Arizona ScQRPions.  FYBO runs for ten hours starting at 1400 UTC to 2400 UTC.

It’s a fun contest that is limited to QRP HF operation only using SSB or CW with 5 watts output max. You can choose to work from home or the field and there are three categories of operators (single op, multi-single, or multi-multi).

FYBO is an easy contest in that the exchange is flexible and there’s no pre-registration required.

The cool thing about FYBO (see what I did there?) is the temperature multiplier which favors those who operate in the coldest temps!

For full information about FYBO including rules and how to submit logs, check out the FYBO information page.

If you’re a POTA, WWFF, or SOTA operator, you can perform a straight-up activation and submit those same logs for FYBO. It just needs to take place during the FYBO contest time frame.

Plotting…

If all goes well, my daughter (K4TLI) and I plan to hike from the QTH up to Pisgah National Forest and perform an activation there.

This will be a test to see if my ankle has healed enough to plot a much longer hike to a SOTA summit from the QTH soon. My fingers are crossed because I’m so eager to get back to hiking.

Plan to Freeze Your B___ Off?

Do you plan to participate in FYBO? Parts of the US and Canada are getting Arctic blasts so those temperature multipliers could be quite impressive! (Just play it safe.) It’ll be chilly here for sure, but I doubt much below freezing.

Antennas, Field Reports, Portable, POTA, QRP

POTA Field Report: Taking the LnR Precision LD-11 out for some fresh air

3 Comments

I mentioned in a previous post that I recently did a thorough clean-out of my shack and home office. It took two full days, and kept me out of the field during that time, but I’m very pleased with the results.

After re-arranging my grab-and-go QRP rigs on their dedicated shelf, one rig was very conspicuous: my LnR Precision LD-11.

Thinking back, it has been ages since I used it in the field–possibly more than a couple of years, in fact. As I packed my bags Sunday morning for a multi-day trip to my hometown, I grabbed the little red LD-11 and stuffed it in my main radio bag. It was time to take it to the field!

Lake James State Park (K-2739)

I didn’t have a lot of time to play radio Sunday afternoon, so Lake Jame State Park was a no-brainer. There, I know I have a number of picnic table options, mobile phone service, and it’s a modest detour off of Interstate 40. Low-hanging fruit in my POTA world.

There was snow on the ground Sunday afternoon, but it was 36F/2C so not terribly cold, just damp.

Due to snow melting in the trees, I set up my station in a picnic shelter where things were dry.

Gear:

Although I’d used the LD-11 recently at home to chase a few SOTA and POTA stations, I had not operated it intensively so it took a little time to reacquaint myself with this little rig.

It’s a gem of a transceiver and has a lot to offer in the field. If you’re interested to learn more about it, I’d encourage you to check out my original review of the LD-11 over at the SWLing Post.

Like the FT-817ND and G90, the LD-11 has no memory keying in CW or Phone. Memory keying is such a useful feature for park and summit activations because it frees up your fist and voice while calling CQ or sending 73s. With the LD-11, I’d be doing all of this “old school” which is absolutely fine for a short activation.

On the air

Although my EFT Trail-Friendly antenna should be resonant on 40, 20, and 10 meters, it was not Sunday because I’m almost certain I’ve finally damaged the radiator coil. I’ve deployed this antenna well over 150 times and yanked it out of countless trees when it got stuck. It’s lasted much longer than I would have ever guessed.

When I tried transmitting on 40 meters, I got a high SWR. Instead of replacing the antenna with another one, I simply hooked up the Elecraft T1 ATU and found a match. This is one good reason why you should always pack an antenna tuner. While employing an ATU might not be as efficient as using a resonant antenna, it can save your bacon in a situation like this and will certainly get the job done (especially if your only goal is a valid field activation).

After matching the antenna, I hopped on the 40M band and logged five CW stations in short order. Obviously, the antenna was working “well enough”–!

As I’ve done with a number of my recent activations, I started recording a video at this point.  I started it after my first five CW contacts due to a lack of space to record a 60 minute video (this one turned out to be 40 minutes and change).

I then moved up to the 20 meter band where I worked one CW station, then switched modes to SSB where I was surprised to work Jon (TI5JON) in Costa Rica, Steve (WA4TQS) in Texas, and Paul (NL7V) in North Pole, Alaska.

Video

This was one of those rare instances where my QRP SSB signal snagged more distant stations than my QRP CW signal.

I’m certain, however, had I spent more time on 20M CW, I would have logged a number of other distant contacts.  Here’s my QSOmap from the activation–not bad for 5 watts into an inefficient antenna:

All-in-all, I was very pleased with the activation. Even though I was making do with a faulty antenna and even though my CW was a little sloppy since I wasn’t quite used to the LD-11 keyer timing, it was so much fun!

I do love the little LD-11 and would certainly recommend grabbing a used one if you find a good deal.

As I mention in the video, the LD-11 is no longer manufactured and it never will be again. The main engineer behind the LD-11, SKY-SDR, and ALT-512–Dobri Hristov (LZ2TU)–passed away in 2020. Dobri was a well-respected fellow and distinguished ham radio operator/DXer. I corresponded with him quite a few times in the past. Sadly, when Dobri passed away, he took the design of all of these rigs with him. His brief period of sickness leading to his death all happened within a year.

So if you find one of these fine transceivers, keep in mind that some internal components (LCD screens, ICs, etc.) might be hard to replace if they fail. These radios are built well, however, so I wouldn’t expect something like that to happen for a very long time.

It was a lot of fun using the LD-11 during this activation and I certainly plan to put it in rotation from now on. Wherever Dobri is now, I like to think he’ll feel those LD-11 signals running through the ether!

Any other LD-11, SKY-SDR, or ALT-512 owners out there?  Please comment!

Antennas, Field Reports, Morse Code, News, Portable, POTA, QRP

POTA Field Report: Pairing the Icom IC-705 with the Elecraft AX1 pocket antenna

3 Comments

I think I’ve said before that I don’t like doing things the easy way. At least, I’m coming to that conclusion.

This Saturday (Jan 30, 2021), I had a small window of opportunity to perform a Parks On The Air (POTA) activation.  My park options were limited because I needed to stay near my home and a store where I was scheduled to do a curbside pickup.

The only viable option–since time was a factor–was my reliable quick hit park.

The Blue Ridge Parkway (K-3378)

I plotted a quick trip to the Blue Ridge Parkway Folk Art Center which is centrally-located and, this time of year, there are few visitors.

But what radio take? It had been a couple of weeks since I used the IC-705 in the field, so I decided to take it and rely only on its supplied BP-272 battery pack.

My buddy Mike (K8RAT) had warned me only a few minutes before my departure that propagation was pretty much in the dumps. I’d also read numerous posts from QRPers trying to participate in the Winter Field Day event and finding conditions quite challenging.

Saturday was the sort of day that I should’ve deployed a resonant wire antenna and made the most of my meager five watts thus collect my required 10 contacts in short order.

And that’s exactly what I didn’t do.

You see, a really bad idea popped into my head that morning: I had a hankering to pair the IC-705 with my Elecraft AX1 super compact vertical antenna.

This made absolutely no sense.

I tried to get the idea out of my head, but the idea won. I suppose, at the end of the day, I’m not about taking the easy path (and I’m obviously a glutton for punishment).

I was also very curious if the mAT-705 Plus external ATU could tune the AX1 on 40 meters. More on that later…

Gear:

I arrived on site a few minutes before noon. Setup was fast–that’s the big positive about using the AX1.

Normally, I deploy the AX1 antenna with my KX2 or KX3 and simply attach it to the BNC connector on the side of the transceiver. The AX1 Bipod gives the antenna acceptable stability during operation.

The IC-705 also has a side-mounted BNC connector, but it’s much higher than that of the KX3 or KX2. I’m not entirely sure I could manipulate the Bipod legs to support the antenna without modification.

That and the AX1 needs an ATU to match 40 meters (where I planned to spend most of the activation). Since the IC-705 doesn’t have an internal ATU, mounting it to the side of the transceiver really wasn’t an option.

I employed my AX1 tripod mount for the first time. On the way out the door, I grabbed an old (heavy) tripod my father-in-law gave me some time ago and knew it would easily accommodate the super lightweight AX1.

On The Air

I first tried using the Mat-Tuner mAT-705 Plus ATU to tune the AX1 on 40 meters.

No go.

I tried both the phone and CW portions of the 40 meter band, but the mAT-705 Plus simply couldn’t find a match. SWR was north of 7:1 – 9:1.

Instead of grabbing the Chameleon MPAS Lite or 2.0 from the car, I decided instead to see if the Elecraft T1 ATU could tune 40 meters.

It did.

In short, I logged my ten contacts to have a valid activation, but it was slow-going. All but two of my contacts were on 40 meters CW. The last two logged were on 20 meters CW.

It was a challenge, but I really enjoyed it! And, frankly, considering the propagation, 5 watts of power only using the IC-705 battery pack, and the inherent inefficiencies using a loaded compact vertical antenna and ATU? I was impressed.

Here’s a QSOmap of my 10 contacts:

I bet my effective radiated power was closer to 2-3 watts.

Typically, the AX1 antenna acts almost like an NVIS antenna on 40 meters, but Saturday it favored Mid-Atlantic and the states of IN, OH, and PA. Normally, I would expect more of a showing from the states surrounding North Carolina.

My last two contacts on 20 meters were with KE5XV in Texas and KB0VXN in Minnesota. Not a bad hop!

It took longer to collect my ten contacts than I had hoped and I ran nearly 25 minutes late to my curbside appointment. I’m a punctual guy, but there was no way I was leaving without my ten! 🙂

Here’s a video of the entire activation. Hint: it’s the perfect remedy for insomnia:

Next time I try to pair the IC-705 with the AX1 antenna, I think I’ll try adding a couple more ground radials and see if the mAT-705 Plus can more easily find a match.

One thing I know for sure: the T1 is a brilliant little ATU. While the mAT-705 Plus was never designed to do this sort of match, it’s comforting to know the T1 can.

I’m very curious if anyone else has paired the Elecraft AX1 with the Icom IC-705 or other QRP transceivers. If so, what was your experience? Please comment!

Field Reports, News, Portable, QRP

POTA Field Report: Activating Lake James State Park (K-2739) with the Yaesu FT-817ND

4 Comments

One question that often faces newcomers to the hobby is: “Should I buy a QRP or a 100W transceiver as my first rig?”

That is a very deep topic, actually, and one to explore in a future post. A 100 watt transceiver will certainly give you more options as they can often pump out 100W or be turned down to 1 watt. If you’re a phone operator only, that’s got some serious appeal. Then again, if you’re operating POTA or SOTA where you are the DX, power–while still important–is much less so than, say, if you were at home trying to work DX.

Again, a deep topic for another post because there is no right or wrong answer.

One of our readers (Phillip) reached out to me a couple weeks ago and asked if the Yaesu FT-818 would make for a good first HF rig. He liked the portability factor, the build quality, the HF/VHF/UHF multi-mode coverage, and the overall flexibility of the rig as a field radio. His goal was to do POTA activations.

We had quite a few emails back and forth about the pros and cons and I decided it might make more sense to simply take my Yaesu FT-817ND (which is nearly identical to the FT-818) to the field and activate a park in both SSB and CW. Since I knew he wouldn’t necessarily have an external antenna tuner from day one, I paired the FT-817 with my resonant 40/20/10 meter end-fed antenna.

Lake James State Park (K-2739)

On January 17, 2021, I pulled into my favorite part of Lake James State park and quickly set up my station. I only had about one hour to complete my activation, so knew this would be a very brief excursion. Since I actually had a minimal amount of gear, it was a quick setup.

Gear:

Since I deployed a resonant antenna, there was no tuning or matching involved which not only makes the most of your 5 watts (in that it’s more efficient), but also saves a bit of time in set up and tuning up.

You might note in the video below that my FT-817 has an accessory board attached to the top: G7UHN’s 817 Buddy Board prototype.

I’m testing this prototype at the moment, but didn’t need to employ it at Lake James since it’s really useful when the rig is on your lap or on on the ground. It essentially gives you top-mounted controls and a larger display to read front panel information from above–incredibly useful for SOTA and proper in-the-field activations. Andy’s v3 board will include a memory keyer–I can’t wait for that one!

Since I had Internet access at this park, I used my Microsoft Surface Go logging tablet to spot myself to the POTA network. I started calling CQ on 40 meters phone (SSB) and within six minutes logged eight stations. Not bad for 5 watts and a wire!

Next, I moved to CW on 40 meters and started calling CQ POTA. The POTA spots page auto-spotted me via the Reverse Beacon Network in short order. In eight minutes, I worked six more stations.

I then moved to twenty meters which was essentially dead, so I called it quits a bit early. I needed to pack up and head to my next destination.

Here’s a QSOMap of this short activation (red polylines are SSB and green CW):

I also made one of my real-time real-life no edit videos during this activation if you’re interested:

Truth is, each time I use the FT-817, I love it more. Sure it’s only 5 watts, has no ATU, has a small display, a clicky T/R relay, and questionable ergonomics, but it is a keeper for sure. Even after 20 years of being in production, it still holds its own and is an incredibly popular radio for good reason.

As I told Phillip, the 817/818 is the Toyota Corolla of the QRP radio world.

Antennas, Field Reports, News, POTA

Mistakes and miscalculations might make us better field radio operators

3 Comments

I don’t know about you, but part of the fun of playing radio in the field are the inevitable frustrations.

It might not feel like it in the moment, but when I eventually overcome the challenges of a mistake, I feel like I’ve truly accomplished something.

That was my little epiphany this morning: making mistakes has perhaps made me a better radio operator. Less-than-efficient field deployments have honed my skills and had a major influence on the gear I pack.

If you’ve read some of my (rather rambling) field reports in the past, you’ll note that I rarely do field activations with the exact same gear combinations each time. I feel fortunate enough that I can pair different radios with different antennas and different accessories.  I get a small thrill out of not knowing exactly how well a combination will work, especially if I’m not activating a rare all-time new park or tough summit for that matter. In cases where getting to the site is a challenge in and of itself, I want to use a trusted combo of gear.

It’s that wee bit of mystery that attracts me to the field.

If I approached POTA more like a contest–where activation and contact numbers were my focus–I would have installed a mobile HF rig in my car a long time ago. I could rack up way more parks and contacts that way. It especially simplifies multi-site activation days since it effectively eliminates the time involved in setting up and later packing up gear.  Mobile operating is the most efficient way to hit number goals: drive up to a site, start calling CQ, work your stations, then move on.

K-6937 & K-4510

(Photo credit: K4TLI)

Yesterday, I did a last minute “two-fer” activation of Pisgah National Forest and Pisgah Game Land. I had not planned to do an activation that day–temps never rose above 29F (-2C) at the QTH day and it also snowed and flurried all day long. Winds were very gusty as well, so it effectively felt much colder on the skin.

I wanted to hike up to the ridge line behind my QTH and do the activation but I knew up there temps would be lower and (worse) winds much stronger. Cold doesn’t really bother me, but strong winds do. This was also the first weekend my ankle felt almost normal after twisting it badly last month. It’s healing and I hope will be in shape for a long hike from my QTH to a six point SOTA summit next weekend with my daughter (K4TLI).

All of those factors combined pointed toward simply staying at home, drinking coffee, and reading a book.

Hazel was ready for some field radio fun, though. (Photo credit: K4TLI)

But I really wanted some outdoor time. And I really wanted to make an activation with my Elecraft KX1, so I decided that instead of hiking up in elevation 800 feet, I’d drive down about 900-1,000 feet to a forest trailhead. That would get me on the air in a protected valley with less wind,  less snow, possibly warmer temps, and much less hiking which would be easier on my ankle.

The Last-Minute Antenna

When I use the KX1 in the field, I typically pack a very simple antenna: one length of radiator wire and one length of counterpoise wire–connected to a BNC binding post adapter, I let the built-in ATU sort out the match.

When I owned my first KX1, I had a magic length of radiator wire (the length of which I can no longer remember) that seemed to work amazingly well  on 40, 30, and 20 meters.

My new-to-me KX1 came with two lengths of wire: one 23′ and one about 20′. Although I made a fun and successful activation with this setup, the radiator was simply too short for the KX1 to find a decent match on 40M.

On the way out the door, I decided to cut a new radiator and counterpoise out of scrap wire I use for antenna experiments.

Being a bit stubborn and also in a hurry to beat sunset, I did no Internet research to sort out the ideal lengths for 40 meters.  I simply cut a 17′ length for the counterpoise and about 27.5′ for the radiator.

In the Field

After arriving on site, I deployed the antenna and tried finding a match on 40 meters with the KX1’s internal ATU.

No go.

I tried a few times hoping maybe the ATU would find something even semi-reasonable in terms of a match, but there simply wasn’t enough radiator to make it work. That was a shame because forty meters would have been the ideal band for yielding quick contacts this time of the afternoon.

I had options, but I wanted to make what I had work.

The activation took time and patience. The 30 meter band was now my best bet and it’s where I logged all ten contacts for a valid activation. I tried 20 meters where I had a 1:1 match, but the band was dead.

At one point, I switched out the KX1 with my KX2 that I also packed. I tried to find a 40 meter match with the superior KX2 ATU, but physics got in the way again. 🙂

40 meters was an option

Let’s be clear here: I could have easily cut 4′ off of the counterpoise and attached it to the radiator and I bet I would have gotten a match on 40M. Since the counterpoise was lying on the ground, its length was less crucial.

The EFT Trail-Friendly end fed antenna was also in my pack.

I also had a perfectly capable 40/20/10 en-fed antenna in my pack. Switching out the antenna would have only taken four minutes.

I bet I could have easily yielded 20 additional contacts on 40 meters because the band was in great shape. Almost without fail, 40 meters is my most productive band.

Working with limitations

Thing is, I’m starting to understand that I like working with self-imposed limitations.

Perhaps this is why I love QRP and low-power radio so much: I get a little thrill out of doing more with less.

Yesterday, even after I realized it would be a struggle to log my final three contacts on 30 meters, I persisted. One motivation was I’ve never completed a full activation using only 30 meters. With a little patience, I knew I could snag my ten contacts.

The only things making it a challenge were the facts that temps were dropping rapidly, winds were picking up, and the sun was setting. Hazel (the POTA dog) who so eagerly jumped in the car when she saw me put on my hiking boots earlier, was also starting to shiver.

Fortunately, after trying another short stint on 20 meters, I returned to 30 and worked two more stations in quick succession giving me a total of nine contacts.

It started to get darker, so I hunted and found an operator calling CQ  on 30 and simply made contact with him. He wasn’t a POTA station, just a general CQ call. He kindly gave me his details for the logs.

Lessons learned

I made a video of most of this activation and will upload it when I have a little bandwidth to do so. I’ll embed it in a shorter field report here on QRPer since I’ve described so much already.

Even though it was a challenge making ten contacts to accomplish a valid field activation with my time constraints, I’ll admit that I really enjoyed the challenge.

Next time I head to the field with the KX1, I’ll actually test the antenna prior to leaving the QTH.

In fact, I’m planning to make two radiators: one at an ideal length for 40 meters and above, and another–much longer–for 80 meters and above. Any advice and personal experience from KX1 owners would be much appreciated.

Perhaps most importantly, it’s only now dawned on me how much I enjoy making the most with self-imposed limitations or “trying to make lemonade with lemons.”

Do you feel the same? I’d love to hear your comments.

Field Reports, News, POTA, QRP

POTA Field Report: Pairing the Mission RGO One with the Chameleon Emcomm III Portable Antenna

Leave a comment

While I tend to use small, field-portable transceivers on many of my Parks On The Air (POTA) activations, I also love using  tabletop transceivers when I have a picnic table available or decide to use my portable table. Tabletop radios often provide more power output when needed and better audio from their built-in speakers.

Although I have an Icom IC-756 Pro transceiver, and an Elecraft KXPA100 amplifier that I can pair with my KX2 and KX3 (or any QRP transceiver for that matter), my favorite tabletop fiel;d radio at present is the Mission RGO One 50 watt transceiver.

If you’re not familiar with the Mission RGO One, I’d encourage you to read my comprehensive review over on the SWLing Post.

In short: it’s a brilliant, simple, tabletop transceiver that’s very happy in the field and a pleasure to operate. My RGO One has the optional built-in antenna tuner (ATU). The rig designer is allowing me to keep this unit on extended loan as I help him evaluate and test updates and upgrades.

While I’ve used the RGO One on numerous POTA activations, I don’t believe I’ve ever made a video of it in use, so I decided to change that last week with another one of my real-time, real-life, unedited (lengthy!) videos of this activation (see video below).

Lake Norman State Park (K-2740)

As I’ve mentioned before, I love activating Lake Norman State Park because it has numerous spots for setting up my gear. While I actually prefer activations that require a bit of hiking, it’s nice from time-to-time to activate a state park that has so many widely-spaced picnic tables under tall trees.  That, and my right ankle is still healing after I twisted it in December, so I’m avoiding any proper trail hiking until it is better.

I made this activation of K-2740 on January 4, 2021.

Gear:

On the Air

This was my first activation of 2021!

Since I have Internet access at Lake Norman, I can check out the  POTA spots page on my phone or tablet and self-spot as well as see spots of other activators.

When I have Internet coverage like this–and I’m not pressed for time–I try to work as many Park-To-Park contacts as I can before I start calling CQ POTA myself.

As I mention in the video, one of my 2021 goals is to obtain a valid activation of each park with only five watts or less. This means that each time I start an activation, at least my first ten stations logged will be with a max of five watts of power. I would actually make the goal for all of my 2021 activations to be 100% QRP, but I evaluate gear regularly and part of that process is to push wattage limits so it’s simply not realistic.

This isn’t actually a crazy goal because a number of my transceivers max out at five watts or less, and I know it won’t be an impediment as I activate parks in CW.

In SSB, though? It makes it a bit more challenging, but certainly not impossible and I’m always up for a challenge!

So I started this activation by trying to work a few Park-To-Park contacts but first cranked the RGO One power down to five watts. Trying to be heard over other hunters in SSB was difficult, but CW was much easier.

After working a few P2P stations, I started calling CQ on the 40 meter band in SSB. I worked about four stations, then switched to CW and worked seven more on 40 meters.

Since I’d snagged my ten contacts for a valid activation, I moved up to 20 meters phone (SSB), cranked up the power to over 40 watts, and started calling CQ POTA and racked up an additional 11 contacts for a total of 26 contacts logged at this activation.

Here’s my QSOmap:

Click to enlarge

Note that I left the callsign labels off the map this time to make it a little easier to see the geo location of the stations I worked.

Real-Time Video

I made a video of the entire activation and posted it on my YouTube channel. As with my other videos, there are no edits and no ads. It’s all real-time and includes my many goof-ups! But hey–mistakes are all a part of a real activation!

Again, if you’d like to know more about the Mission RGO One, you might check out my review on the SWLing Post.

Feel free to comment with your thoughts or questions and thank you for reading QRPer.com!

Field Reports, News, POTA

POTA 2020: Taking a look at my stats

6 Comments

A few days ago, I checked out the leaderboard statistics on the POTA website to see exactly how many parks I activated and hunted in 2020.

This was one of the first times I’d checked my numbers in weeks. At the end of the day, I’m not a competitive guy, and perhaps one of the reasons I like POTA is it’s more an activity, less a contest.

National Parks On The Air (NPOTA) in 2016 was not a contest either, per the ARRL, but it felt more like one since it was a one year event. I definitely caught the NPOTA bug that year and mostly within the space of 5 months activated over 90 parks. It helped that my girls’ school bordered a national park.

One of my first NPOTA activations in 2016 with buddy Eric (WD8RIF).

Don’t get me wrong, NPOTA was AMAZING fun, but I had some serious withdrawal by the end of the event and even felt a touch of burn-out.

Turns out, so many NPOTA participants had withdrawal, that they formed POTA and even turned it into a non-profit organization.

POTA is a multi-year activity and is also international unlike NPOTA.

I do believe POTA has injected some much-needed life into amateur radio and has given operators a reason to take their radios to the field.

Back to the numbers

With all of that said, I was eager to see what my numbers looked like for 2020, so I checked out my entry on the leaderboard:

Activations

Here’s a breakdown of my activation numbers:

  • 86 Activations
  • 37 Unique Parks
  • 1721 total contacts:
    • 999 CW
    • 0 Data
    • 722 Phone

I found these numbers very interesting.

First of all, had I worked one more CW station, I would have made 1,000 contacts! Still: I like the ring of 999.

These numbers show me that CW has, indeed, become my favorite mode. I’ve only been activating in CW since July 2020 and it still overtook my total number of phone contacts.

The venerable Mountain Topper MTR-3B

To be clear, though: I love SSB and CW equally.

Thing is, I have come to appreciate how effective CW is when operating at QRP levels. Also, it’s much easier to find a clear spot on the dial to call CQ in CW–SSB, some weekends, it can be a real challenge

In addition, as long as I schedule my activation in advance, the POTA spots page will auto-spot me by pulling my details from the reverse beacon network (RBN). This is HUGE for me since a good 60% of the parks I activate have no mobile internet connectivity.

SSB, however, has much greater numbers in terms of operators. I’d be willing to bet there are seven SSB-only operators to every one operator who uses CW.

Phone activators sometimes amass DXpedition-like pile-ups. It’s pretty amazing.

No doubt, if you want to really pump up your POTA numbers, the best plan is to use both phone and CW.

Hunter Stats

I’m a very casual POTA hunter, still the numbers were less modest than I had assumed:

  • 281 Unique Parks
  • 337 Total Contacts
    • 203 CW
    • 1 Data
    • 133 Phone

POTA 2021

As with 2020, I won’t pay a lot of attention to my numbers. I do have a few goals, though:

  • Achieve all of my activations with five watts or less
  • Get my daughter K4TLI in on the POTA action (she’s close to taking her General test)
  • Make at least one data mode activation
  • Go to at least 20 new parks
  • Continue to have fun!
K4TLI logging for me like a champ

To be clear about my five watt challenge: I will use more than 5 watts in the field (indeed, I did yesterday). I often test transceivers and antennas during POTA activations, so need to push the power settings from time to time.

My goal is to work my first 10 contacts (thus achieving the required amount for a valid activation) of each activation with 5 watts or less.

How about you?

If you’re a POTA activator or hunter, have you looked at your numbers recently? What are your goals for 2020? If you’re new to POTA, do you plan to join in on the fun this year? If so, what equipment do you plan to use?

Please comment!

Antennas, Field Reports, Grab And Go, News, Portable, POTA, QRP

POTA Field Report: Pairing the Elecraft KX3 with the AX1 antenna and seeking distant stations

16 Comments

Although I’m a huge fan of wire antennas in the field, since I started using CW during my Parks On The Air (POTA) activations, I’ve really enjoyed experimenting with compromised portable antennas.

Typically, there’s a trade off with field antennas:

High-performance antennas tend to take more time to install. Some of my highest performance antennas are dipoles, doublets, delta loops, and end fed wire antennas. All of them require support from a tree if I want maximum height off the ground. Some (like the dipole) require multiple supports. While I actually enjoy installing wire antennas in trees, it typically takes me at least 10 minutes to install a wire antenna if it only needs one support and one counterpoise.

Compromised or low-profile antennas may lack performance and efficiency, but are often much quicker and easier to deploy.

In my opinion, field operators should keep both types of antennas in their arsenal because sometimes the site itself will dictate which antenna they use. I’ve activated many sites where wire antennas simply aren’t an option.

That was not the case last Tuesday, however.

Tuttle Educational State Forest (K-4861)

On Tuesday, December 29, 2020, I stopped by Tuttle Educational State Forest (K-4861)–one of my favorite local state parks–for a quick, impromptu activation.

I had no less than four antennas in my car that day and Tuttle is the type of site where I can install pretty much anything: they’ve a spacious picnic area with large tables, tall trees, and parking is close by. Tuttle is the perfect place to deploy not only a large wire antenna, but a large radio if you wish since you don’t have to lug it far from the car.

But en route to Tuttle I decided to take a completely different approach. One of the four antennas I had in the car that day was the Elecraft AX1 antenna.

Without a doubt, the AX1 is the most portable antenna I own. It’s so compact, I can carry it in my pocket if I wish.

When I first purchased the AX1, I was very skeptical and assumed it would only work when “the stars aligned”–days with better-than-average propagation and lots of POTA hunters/chasers looking for me.

The first time I used the AX1 in the field, it impressed me (understatement alert).

The second time, same thing.

In all of my AX1 activations, however, I had only operated on the 40 meter band where the antenna’s footprint looked more like a NVIS antenna than a vertical. Meaning, most of my contacts were in neighboring states like Tennessee, South Carolina, Virginia, and Georgia (typically, those states are in my 40 meter skip zone).

The reason I hadn’t tried 20 or 17 meters with the AX1 is because I would start an activation on the 40 meter band and accumulate enough contacts to achieve a valid activation. Since I’m often pressed for time, I simply didn’t bother configuring the antenna for the higher bands.

Time for that to change!

The question I wanted answered at Tuttle: could the AX1 antenna work “DX” stations? By DX, I mean POTA DX, so distant states and provinces primarily–not necessarily other countries.

Gear:

On the air

I paired the Elecraft KX3 with the AX1 at Tuttle. This was the first time I’d ever tried this particular transceiver/antenna combo.

After setting up, I started on the 20 meter band and called CQ for a few minutes.

The first two stations I worked were in Texas (KF9RX and K5RX).

The third station (W6LEN) was in California.

California!?!

Honestly, it was/is hard for me to fathom how in the world 10 watts into a tabletop telescoping whip antenna could work a station exactly 2,083 miles (3,352 km)–and three time zones away–from my picnic table. I’m sure W6LEN has a great antenna on the other end, but I bet he would be surprised to learn that my 10 watt signal was being radiated by such a wee antenna.

 

 

I then worked stations in Florida (K2WO), Minnesota (N0UR), and New Hampshire (W2NR) and decided to move to 17 meters.

On 17 meters I worked W2NR in New Hampshire once again.

I should note here that each time you work a station on a different band or with a different mode, it counts as a separate contact in POTA. In other words, my contacts with W2NR on 20 meters and 17 meters counts as two logged contacts toward my overall QSO count. I’m very appreciative of hunters who go out of their way to work me on different bands and modes: those extra contacts help me achieve a valid activation in short order.

I then moved to 40 meters and worked stations from Tennessee, West Virginia, Ohio, and Michigan.

Video

Here’s a video of the entire activation. It’s a long video as it starts at set-up and continues until my last contact. There are no edits in this video–it’s a real-time, real-life deal and contains all of my bloopers:

Note that in the video I had the KX3’s volume maxed out so that it could be picked up by my iPhone microphone. The KX3’s wee internal speaker was vibrating the chassis ever so slightly. On the 40 meter band, it resonated enough that it moved the encoder slightly. Next time, I’ll plan to bring a portable external speaker (if you have any suggestions of good ones, let me know).

And here’s a QSOmap of the activation:

Click to enlarge.

Bioenno 3aH LiFePo battery

I should also add that I’m very pleased with my new Bioenno 3aH LiFePo 12V battery. You can see it in the photo above–it’s slim, lightweight, and very compact.

I purchased it during Bioenno’s Black Friday sale. I was a little concerned it might not have enough capacity to carry me through multiple activations–my other LiFePo batteries re 4.5 and 15 aH–but that does not seem to be the case at all! Not only did it provide nearly an hour of intense use on this activation, but it also powered three activations the previous day–all four activations on one charge! Brilliant!

Radio magic

As I mentioned in a previous post, this was one of those activations that reminded me of the magic of low-power radio. It was incredibly fun!

For all of those phone/SSB operators out there, I will eventually see how successful I can be doing a phone-only activation with the AX1 antenna. I’ll plan to make a video of it as well. I’ll need to plan this for a day when I have more time to spend on the air and at a site where I know I’ll have internet access to spot myself to the POTA network.  SSB isn’t quite as effective as CW when operating with a setup this modest. Still–it can be done! It just requires a little more patience. Please let me know if this sort of thing would interest you.

Until then, Happy New Year and 73s to everyone!

Cheers,

Thomas (K4SWL)