Last Tuesday (March 2, 2021), I needed to make a quick trip to south Asheville and pick up some gear I had ordered from REI. Of course, I had a hankering to fit in a Parks On The Air activation. I contacted my buddies Eric (WD8RIF) and Mike (K8RAT) and mentioned I might make a visit to the Blue Ridge Parkway [it’s always a good idea to have others look for you in case your unable to spot yourself on the bands].
By the time I jumped in the car, though, I talked myself out of doing the activation. Propagation was poor and I had a maximum of 30 minutes to fit in a valid activation.
After picking up my gear at REI, I realized, though, that a 30 minute limit made for an awfully fun challenge.
I had to pass by the parkway to go home, so why not? Right?
I did a quick check and, yes(!) I had the Elecraft KX2 and CHA MPAS Lite antenna in the car.
Before leaving REI, I scheduled my activation on the POTA website so that the site would know to auto-spot me if the Reverse Beacon Network picked me up.
Blue Ridge Parkway (K-3378)
I arrived at the parkway in very short order. I decided to do the activation at the Blue Ridge Parkway Visitor’s Center and Headquarters. Normally, I avoid this location because it’s busy and the best spots to set up a radio are in the path of visitors walking around the perimeter of the grounds.
It was a cold, overcast Tuesday morning so, as I expected, I almost had the place to myself.
I deployed the CHA MPAS Lite vertical in very short order–perhaps 3 minutes. Since I had also packed my Pixel 3 camera/phone and tripod in the car, I even recorded a video of the full activation (see below).
In short? I snagged my 10 contacts in about 19 minutes on the air–all on 40 meters CW. Not too bad for a Tuesday morning with five watts and a vertical.
Here’s a QSOmap of the contacts I made:
I also had a first at this activation! I worked ND9M/MM. To my knowledge, I’ve never worked a maritime mobile station at a park activation–certainly not in CW! The map above omits this contact since the location was unknown.
When I submitted my log to Bill DeLoach (our regional contact for POTA logs) said I really need a “Wham Bam!” award for this quick activation. Ha ha!
I’ll let you in on a little secret. Don’t tell anyone, but I held off making my first Summits On The Air (SOTA) activation until the stars aligned and I could activate one particular summit completely on foot from my QTH.
Last Thursday (February 25, 2021), my daughter and I hiked to Lane Pinnacle (W4C/CM-018) and performed my first Summits On The Air (SOTA) activation.
Why did I wait so long?
We live in the mountains of western North Carolina where (obviously) there are numerous SOTA summits to activate.
But I wanted Lane Pinnacle to be the first.
Why? Well, it’s the one summit I can hike to directly from my house with my daughter Geneva (K4TLI) and enjoy a proper father/daughter day hike.
I had planned to do this hike last year, but I injured my ankle and let’s just say that the hike to Pinnacle isn’t a beginner’s run. I knew my ankle would need to properly heal before the journey.
This is also more of a late fall to very early spring hike due to the amount of thick foliage we knew we would have to mitigate. It’s so much easier to keep your bearings when there are no leaves on the trees nor on the green briar!
Last Thursday, I felt confident that my ankle was up to the task. We had a break in the weather as well with moderate temps and lots of sunshine (this, after several days of rain). We knew things could be muddy and slippery, but we also knew that with my busy schedule this might be our last chance to hit the summit before the mountains green up.
So we packed a lunch, plenty of water, radio gear, and (of course) emergency/first-aid kits while trying to keep our backpacks as light as possible.
Hitting the trail!
The first part of the hike requires trailblazing to a ridge line. The distance is short, but the ascent is steep (about 800 feet). We hike this portion regularly, so knew how to pick our path and avoid the steeper, slippery bits.
K4TLI lead the way!
On the ridge line, we intersected an established single track trail and enjoyed the hike across a couple of smaller summits until we intersected the Blue Ridge Parkway.
If I’m being honest, I had some serious concerns that the trailhead to Lane Pinnacle would be closed. This portion of Blue Ridge Parkway is currently closed to motor vehicles (for the winter season) and I had noticed a number of “trail closed” signs on other portions of the parkway.
Guessing this may be a type of shelf fungus?
If the trail was closed, I planned to simply activate the parkway and Pisgah National Forest for the POTA program. I never hike on trails that have been closed by the park service because I like to obey the rules and I certainly don’t want to paint SOTA activators in a bad light.
When we crossed the parkway, we were incredibly pleased to see that the trailhead was open.
The ascent from the parkway to Lane Pinnacle is about 1,000 feet (305 meters) of elevation gain over a pretty short distance. The trail we were taking–turns out–was primitive. It basically lead us straight up the slope (no switch backs following lines of elevation, for example) and simply fizzled out about one third of the way up. We could tell it isn’t traveled often at all (although we did find a massive fresh bear track in the mud on the trail!).
Obligatory SOTA report “foot in snow” photo. 🙂
I bushwhacked our way to the top–at times, the slope was about 45 degrees and slippery, but we easily found our way to the summit where our goat path intersected the Mountains To Sea trail.
We found an amazing overlook and took in views of the Bee Tree Reservoir as we ate our lunches.
Geneva grabbed her dual-band HT and made the first summit contact with our friend, Vlado (N3CZ) on 2 meters FM.
On the Air
I knew there would be short trees on the summit of Lane Pinnacle, but I also knew that I wanted to get on the air as soon as possible to allow extra time for our hike home.
I did pack a super compact wire antenna, but opted instead for the Chameleon CHA MPAS Lite vertical. I paired it with my Elecraft KX2.
The great thing about the CHA MPAS Lite is how quick it is to deploy–it might have taken me all of three minutes.
Since it was noon, I decided to start on the 20 meter band. I found a clear frequency, started calling “CQ SOTA” with the KX2 memory keyer, and spotted myself to the SOTA network via the excellent SOTA Goat app on my phone.
I had also scheduled my activation on the POTA website in advance because Lane Pinnacle is in Pisgah National Forest (K-4510). My buddies Mike (K8RAT) and Eric (WD8RIF) were also helping to spot me in the unlikely event I wouldn’t have cell phone service on the summit.
Within 20 seconds of submitting the spot to the SOTA network I had a CW pileup.
In all of my hundreds of field activations, I can’t think of a single time that I generated a CW pileup on 20 meters in such short order with five watts and a vertical.
The first station I logged was N1AIA in Maine. The second station was F4WBN in France. The race was on!
It took every bit of CW skill I had to pull apart the stations on 20 meters. It was so much fun!
I eventually worked Spain and all of the west coast states (WA, OR, and CA) and numerous stations throughout the Rockies and Midwest.
I then moved to 40 meters where I worked stations in the Mid-Atlantic, Ohio Valley, and in the Southeast.
In the end, I had to keep my total time on the air short because I wanted to take my time finding a path from the summit back down to the Blue Ridge Parkway.
In 30 minutes I worked 30 stations. I’m not a seasoned CW operator, so this was quite the accomplishment.
Here’s a QSOmap of my contacts:
I was chuffed! What a fabulous activation to kick off my SOTA adventures.
Video
This time, I did not make a video of the actual activation. For one thing, I didn’t want to carry a folding tripod for the camera and I didn’t want to ask my daughter to film it either. I wanted to keep things as simple as possible to make the most of the airtime I had.
I did, however, make a short video before and after. You can check it out on my YouTube channel:
Hiking home
I really wish we could have stayed on the summit for an hour longer making contacts, but I knew it would be wise to allow extra time to descend Lane Pinnacle especially since I knew a front was moving through later that day.
I decided it would be easier to do my own bushwhacking back down the mountain rather than try to retrace our previous steps. We took our time and I followed elevation lines to make it slightly less steep. Since I took a more south westerly descent, when we reached the parkway, we had to hike north to reach the original trailhead.
The rest of the hike was totally uneventful and incredibly fun. The weather held and we took in the views, the wildlife, and invaluable father/daughter time.
That was the first strenuous hike I had done in months due to my ankle, so let’s just say I was feeling “spent” after our 6.5 hour adventure taking in 2,000 feet (610 meters) of elevation to the summit.
I knew it was bad when I even dreaded walking upstairs to take a shower. I think I remember telling my wife, “I’m never building a house with stairs again!”
More SOTA!
Now that I’ve got Lane Pinnacle in the books, I’m ready to start hitting the summits! I’ve got a lot of pent up SOTA energy!
My goal is to activate a total of ten this year. That may sound like a modest number, but since at this point I’m less interested in “drive-up” summits, it’s more difficult to fit SOTA summits into my schedule than, say, typical POTA/WWFF parks.
In fact, I’ve already plotted my next SOTA activation and hope to do it within the next couple of weeks. It’s also a meaningful (to me) summit.
How about you?
Are you a SOTA activator or are you planning your first SOTA activation soon? Please comment!
Last week, I squeezed in two activations on the afternoon of February 17, 2021 to test out the MFJ-1984LP end fed half wave antenna that MFJ sent me to evaluate.
The first park was Lake James State Park where I paired the MFJ-1984LP with my Icom IC-705 (click here to read the report and watch the video). The second was South Mountains Game Land where I paired it with the Elecraft KX2.
In both instances, I did not use an ATU because the EFHW is resonant on the bands where I operated. I bypassed the internal ATU in my KX2 and, of course, the IC-705 has no ATU.
I’ve got a very busy few days ahead including a presentation tomorrow at the Virtual Winter SWL Fest (the topic being QRP transceivers). In lieu of writing a full field report, I’ll simply share the (partial) video I made at the activation.
I’ll admit it, I was not on my “A Game” at that activation. Not only did I forgot to press the start button on the camera, but I also struggled copying CW more than I usually do. I had a lot on my mind that afternoon, though, and really felt pressed for time.
I don’t mind sharing this experience, however, because we all have days like these.
For the past four days here at my mountain QTH in North Carolina, I haven’t seen the sun. The cloud ceiling has been low and our house has been in the middle of it. It’s been rainy and foggy with temps floating a few degrees above freezing.
Last Tuesday (February 9, 2021), however, we had one day with glorious weather and I’m so pleased I carved out 90 minutes to perform a park activation on my way back home from a short trip.
I picked Lake James State State Park (K-2739) because it’s such a short detour and has numerous spots where I could set up my gear.
The temperature was a truly balmy 60F/15.5C–possibly even a tad higher.
Lake James State State Park (K-2739)
On my way to Lake James, I knew I’d use my Elecraft KX2 (it was the only transceiver I had on this trip) but debated what antenna to deploy. I chose the Chameleon MPAS 2.0 vertical antenna because, to my knowledge, I had never paired it with the KX2 and I enjoy shaking up my transceiver and antenna combos.
The brilliant thing about antennas like the CHA MPAS 2.0 is how quick they are to deploy: it takes me all of three minutes or so.
On the air
Since the Elecraft KX2 has a built-in battery and built-in ATU, I basically connected the radio directly to the antenna and was on the air in moments.
The CHA MPAS 2.0 is the vertical equivalent of a random wire antenna: it’s not resonant on any one frequency and requires an antenna tuner to achieve a good SWR.
As I mentioned in the video (below) I always keep my expectations low when deploying a vertical antenna in areas like western North Carolina where ground conductivity is poor.
Maybe the antenna decided to prove me wrong, because I hopped on 20 meters CW and logged a number of stations across the country including Washington state and British Columbia with a measly five watts.
It also happened that my buddy and fellow POTA activator, Steve (KC5F), was just down the road activating another site in the same county. It’s rare that Steve and I can work each other because, typically, we’re too close for skywave propagation and too far for ground wave. Not this time! We were close enough for ground wave on multiple bands–it was great fun working him park-to-park on every band I tuned.
I moved from 20 meters to 17 meters, to 30 meters, 40 meters and back up to 20 meters SSB.
The great thing about using the MPAS 2.0 is how incredibly easy it is to pick up and move from band-to-band–there’s no manually tuning a coil or changing links on a multi-band diplole. In fact, the MPAS 2.0 covers 160-6 meters, so I’ve lots of options if band conditions are wonky.
Video
Here’s an unedited video of the entire activation:
In the end, here’s how my QSOmap looked with 32 stations logged:
I look back at activations like this and am reminded of the magic of HF radio. It’s truly phenomenal, in my mind, that with less power than it takes to light an LED bulb, I can make contacts across the continent pretty effortlessly–CW or SSB–even during the solar doldrums! Good fun!
In other news, my ankle is healing nicely and once this cycle of nasty weather clears, I’m looking forward to putting some SOTA sites on the air!
How about you? Do you have any field radio plans? Has the weather or C-19 lockdowns gotten in the way? Please comment!
Some of my most enjoyable field activations are those involving the least amount of equipment and accessories. Maybe it’s my “less is more” mentality, but it is amazing when all I need to get on the air is one radio, a feedline, logging notebook, and a simple antenna.
That was my set-up earlier this week (February 8, 2021) when I activated Kerr Scott State Game Land–a site I hadn’t visited since last summer.
Kerr Scott State Game Land (K-6918)
I was the first person to activate Kerr Scott State Game Land back in June of 2020.
I vividly remember that activation because, as I noted in my field report on the SWLing Post, it was Kerr Scott that taught me an invaluable lesson:
“[I]f you don’t have a “spot” of your activation on the POTA site, it’s like you don’t exist.”
This was truly a tipping point that lead me down the path of doing CW activations in order to benefit from auto-spotting via the Reverse Beacon Network (RBN). Only a couple weeks after this activation, I made my first CW activation and the rest is history. While I still use SSB during activations, CW has become my favorite mode even though I’m still not that great of an operator.
I speak about this a bit more in my activation video below.
Once I arrived on site, I deployed my EFT Trail-Friendly 40/20/10 meter end-fed resonant antenna.
The last few times I deployed this antenna in the field, it hasn’t been resonant on 40 meters and I suspect this is due to damage to the coil near the end of the radiator. I decided I’d give it one last test by suspending it in an overhanging tree branch about 50 feet high so it would not touch other branches.
When I turned on the KX2, I set the internal ATU to “bypass” and tested SWR. Sadly, it was unacceptable, so I re-activated the ATU to get a good match.
My buddy and fellow POTA activator, Steve (KC5F), reminded me recently that the radiator on this antenna can be replaced with enough wire to make a simple end fed half wave. That’s probably what I’ll do because, frankly, this antenna has served me so well for five years and over 150 park activations I’m not ready to simply toss it. I will need to order some proper wire for the EFHW, though!
On The Air
Since I have no mobile phone/Internet service at this site, I decided to make this a CW only activation, hopefully taking full advantage of auto-spotting to the POTA spots page.
I started on 40 meters because I had pre-arranged with my buddies Mike (K8RAT) and Eric (WD8RIF) to listen for me on 7063 kHz. I did this in case auto-spotting wasn’t working, which does happen from time-to-time. It’s always important to have a back-up if possible especially for sites (like this one) that carry significant travel time.
I hopped on 40 meters, called CQ POTA and within 29 minutes, I logged 26 stations. That’s about as much activity as I could possibly expect during a Monday morning activation!
Next, I moved to 20 meters and started calling CQ. The first station I worked was CU3BL in the Azores, then WD5GRW in Texas, AB6QM in California, then IK4IDF in Italy, and finally KH2TJ in California.
I then moved to 30 meters and worked N5GW in Mississippi before going QRT with a total of 32 stations logged.
Not at all bad using 5-10 watts!
Here’s a QSOmap of this activation (click to enlarge):
Activation Video
I made a real-time, real-life, no edit, no advertisements video of this activation. Feel free to check it out if you like:
One of the things I rarely mention in my videos and field reports is how much I love the trips to/from an activation site. I’m a traveler at heart and while I’ve been fortunate enough to travel to and live in some pretty amazing countries and cities, I still have a deep appreciation for simply driving through the countryside and taking in the scenery. I appreciate the mundane as much as I do the majestic. It’s a beautiful drive.
Kerr Scott Game Land is located in the little farming community of Boomer, NC which, I understand, was named after its first postmaster, Ed “Boomer” Matheson.
Warrior Creek, next to my activation site at Kerr Scott
Before it was called Boomer, the community was known as Warrior Creek–the very creek running through Kerr Scott Game Land.
Even though I know there’s no connection, when I hear the name Boomer I can’t help but think of the incredibly cute and cheeky red squirrel that we WNC natives call “Boomers.”
Last week, I activated Pisgah Game Land and Pisgah National Forest (K-6937 & K-4510)–things didn’t exactly go according to plan. I still achieved a valid activations–meaning, I logged ten contacts–but I cut my antenna too short.
In short: I cut my wire antenna too short and my KX1 and KX2 ATUs couldn’t find an acceptable impedance match on the 40 meter band. This pretty much forced me to make do with 30 meters and above unless I modified or switched antennas.
The 40 meter band tends to be my most productive band, particularly on days like last Saturday when I’m operating in the latter part of the afternoon.
Maybe it was stubbornness, but I was determined to make a valid activation with that four-feet-too-short antenna.
I first hopped on the air with my Elecraft KX1 (above) and logged a few contacts on 30 meters. I then tried 20 meters, but the band was dead.
Eventually, I pulled the Elecraft KX2 out of the bag with the hope it might actually find a match on 40 meters, but as I said in my previous post, that darn physics stuff got in the way.
That’s okay, though. Although the sun was starting to set and I didn’t want to pack up in the dark, I took my time and eventually logged ten contacts for a valid activation. I actually enjoyed the challenge.
I complain about my wire antenna, but in the end, it made the most of my three watts by snagging stations from New Hampshire, Ontario, Illinois, Arkansas and several states in between.
Against my better judgement, I made a video of this activation. As with all of my videos, they’re real-time, real-life, and have no edits. (They also have no ads.)
A few readers and subscribers had asked me to include the odd video where I actually do a full station set up including the installation of a wire antenna–that’s what you’ll see in this video:
At the end of the day, this was still an incredibly fun activation.
This was the first time I’ve ever completed a valid activation only using the 30 meter band.
Next time, though, you’d better believe I’ll cut my antenna to be the ideal length for 40 meters and above!
How long?
If you use a similar antenna with your KX1, KX2, KX3, or other transceiver, I’m curious what lengths you find work best for 40 meters an above. Bonus points for 80 meters. Please comment!
I don’t know about you, but part of the fun of playing radio in the field are the inevitable frustrations.
It might not feel like it in the moment, but when I eventually overcome the challenges of a mistake, I feel like I’ve truly accomplished something.
That was my little epiphany this morning: making mistakes has perhaps made me a better radio operator. Less-than-efficient field deployments have honed my skills and had a major influence on the gear I pack.
If you’ve read some of my (rather rambling) field reports in the past, you’ll note that I rarely do field activations with the exact same gear combinations each time. I feel fortunate enough that I can pair different radios with different antennas and different accessories. I get a small thrill out of not knowing exactly how well a combination will work, especially if I’m not activating a rare all-time new park or tough summit for that matter. In cases where getting to the site is a challenge in and of itself, I want to use a trusted combo of gear.
It’s that wee bit of mystery that attracts me to the field.
If I approached POTA more like a contest–where activation and contact numbers were my focus–I would have installed a mobile HF rig in my car a long time ago. I could rack up way more parks and contacts that way. It especially simplifies multi-site activation days since it effectively eliminates the time involved in setting up and later packing up gear. Mobile operating is the most efficient way to hit number goals: drive up to a site, start calling CQ, work your stations, then move on.
K-6937 & K-4510
(Photo credit: K4TLI)
Yesterday, I did a last minute “two-fer” activation of Pisgah National Forest and Pisgah Game Land. I had not planned to do an activation that day–temps never rose above 29F (-2C) at the QTH day and it also snowed and flurried all day long. Winds were very gusty as well, so it effectively felt much colder on the skin.
I wanted to hike up to the ridge line behind my QTH and do the activation but I knew up there temps would be lower and (worse) winds much stronger. Cold doesn’t really bother me, but strong winds do. This was also the first weekend my ankle felt almost normal after twisting it badly last month. It’s healing and I hope will be in shape for a long hike from my QTH to a six point SOTA summit next weekend with my daughter (K4TLI).
All of those factors combined pointed toward simply staying at home, drinking coffee, and reading a book.
Hazel was ready for some field radio fun, though. (Photo credit: K4TLI)
But I really wanted some outdoor time. And I really wanted to make an activation with my Elecraft KX1, so I decided that instead of hiking up in elevation 800 feet, I’d drive down about 900-1,000 feet to a forest trailhead. That would get me on the air in a protected valley with less wind, less snow, possibly warmer temps, and much less hiking which would be easier on my ankle.
The Last-Minute Antenna
When I use the KX1 in the field, I typically pack a very simple antenna: one length of radiator wire and one length of counterpoise wire–connected to a BNC binding post adapter, I let the built-in ATU sort out the match.
When I owned my first KX1, I had a magic length of radiator wire (the length of which I can no longer remember) that seemed to work amazingly well on 40, 30, and 20 meters.
My new-to-me KX1 came with two lengths of wire: one 23′ and one about 20′. Although I made a fun and successful activation with this setup, the radiator was simply too short for the KX1 to find a decent match on 40M.
On the way out the door, I decided to cut a new radiator and counterpoise out of scrap wire I use for antenna experiments.
Being a bit stubborn and also in a hurry to beat sunset, I did no Internet research to sort out the ideal lengths for 40 meters. I simply cut a 17′ length for the counterpoise and about 27.5′ for the radiator.
In the Field
After arriving on site, I deployed the antenna and tried finding a match on 40 meters with the KX1’s internal ATU.
No go.
I tried a few times hoping maybe the ATU would find something even semi-reasonable in terms of a match, but there simply wasn’t enough radiator to make it work. That was a shame because forty meters would have been the ideal band for yielding quick contacts this time of the afternoon.
I had options, but I wanted to make what I had work.
The activation took time and patience. The 30 meter band was now my best bet and it’s where I logged all ten contacts for a valid activation. I tried 20 meters where I had a 1:1 match, but the band was dead.
At one point, I switched out the KX1 with my KX2 that I also packed. I tried to find a 40 meter match with the superior KX2 ATU, but physics got in the way again. 🙂
40 meters was an option
Let’s be clear here: I could have easily cut 4′ off of the counterpoise and attached it to the radiator and I bet I would have gotten a match on 40M. Since the counterpoise was lying on the ground, its length was less crucial.
The EFT Trail-Friendly end fed antenna was also in my pack.
I also had a perfectly capable 40/20/10 en-fed antenna in my pack. Switching out the antenna would have only taken four minutes.
I bet I could have easily yielded 20 additional contacts on 40 meters because the band was in great shape. Almost without fail, 40 meters is my most productive band.
Working with limitations
Thing is, I’m starting to understand that I like working with self-imposed limitations.
Perhaps this is why I love QRP and low-power radio so much: I get a little thrill out of doing more with less.
Yesterday, even after I realized it would be a struggle to log my final three contacts on 30 meters, I persisted. One motivation was I’ve never completed a full activation using only 30 meters. With a little patience, I knew I could snag my ten contacts.
The only things making it a challenge were the facts that temps were dropping rapidly, winds were picking up, and the sun was setting. Hazel (the POTA dog) who so eagerly jumped in the car when she saw me put on my hiking boots earlier, was also starting to shiver.
Fortunately, after trying another short stint on 20 meters, I returned to 30 and worked two more stations in quick succession giving me a total of nine contacts.
It started to get darker, so I hunted and found an operator calling CQ on 30 and simply made contact with him. He wasn’t a POTA station, just a general CQ call. He kindly gave me his details for the logs.
Lessons learned
I made a video of most of this activation and will upload it when I have a little bandwidth to do so. I’ll embed it in a shorter field report here on QRPer since I’ve described so much already.
Even though it was a challenge making ten contacts to accomplish a valid field activation with my time constraints, I’ll admit that I really enjoyed the challenge.
Next time I head to the field with the KX1, I’ll actually test the antenna prior to leaving the QTH.
In fact, I’m planning to make two radiators: one at an ideal length for 40 meters and above, and another–much longer–for 80 meters and above. Any advice and personal experience from KX1 owners would be much appreciated.
Perhaps most importantly, it’s only now dawned on me how much I enjoy making the most with self-imposed limitations or “trying to make lemonade with lemons.”
Do you feel the same? I’d love to hear your comments.
Tuesday last week (December 8, 2020), I was still on a much-needed weeklong vacation near Charleston, South Carolina with my family. We had the day wide-open to enjoy the outdoors and my wife suggested we find a nice park where I could play radio and we could enjoy a picnic.
I looked on the POTA map and chose the Bonneau Ferry Wildlife Management Area (K-3888) primarily because I thought it would be fun to spend some time near a lake.
The drive there was over an hour from where we were staying on John’s Island, but well worth it!
Turns out, it was pretty chilly and windy that day due to a front that had moved through the area during the night. After exploring the area a bit, my wife and daughters decided to enjoy their picnic in the car while I did the activation!
On the air
The spot we found near one of the lakes was ideal for a POTA activation. Although there were numerous large trees that were perfect for wire antennas, I deployed my CHA Emcomm Lite vertical knowing it would also perform well (and it did!)
Because the CHA MPAS Lite is so easy to deploy, I was on the air in a matter of minutes. I decided to stake it in the ground next to the water about 50 feet from my operating position under a tree. You can see it in the photo above (it’s rather stealthy!).
I’m not at all bothered by cold weather, but it was windy enough that my hands did get cold.
I started calling CQ around 17:55 UTC and by 18:34 I had logged a total of 21 stations on both 40 and 30 meters.
POTA hunters will often thank me for activating a park. I always tell them “it’s my pleasure.” Because it is! Just check out the view from my shack!
This is why I love POTA and SOTA so much. I’m a firm believer that radios and their operators are meant to be outdoors!
When I operate outdoors, I tune out everything else in the world and just enjoy the radio time and the outdoors. It’s bliss.
I kept my total time on site less than one hour so my family and I could continue exploring the area and even get a long walk on the beach before sunset.
Here’s a map of the stations I worked with 5-10 watts. Since I discovered this park had never been activated in CW, I made it a CW-only activation:
If you find yourself in the Charleston, SC area, I highly recommend a trip to Bonneau Ferry WMA for some Parks On The Air fun!
One of the great things about Parks On The Air (POTA) is it provides a brilliant excuse to discover public lands that might otherwise go unnoticed while on vacation.
I’m currently taking a little vacation time with the family on the coast of South Carolina and Saturday, December 5, 2020, we decided to explore a nearby park and activate it. I happened upon the ACE Basin Project on the POTA website and thought it sounded intriguing. Our plan was to go to the park, perform a quick activation, perhaps hike a bit, then go to the coast for a beach walk.
I’ve been to wildlife management areas and game lands that have been very basic perhaps only featuring a parking area and a trail or two– which is fine, frankly.
But sometimes you happen upon gems like the Ernest F. Hollings ACE Basin National Wildlife Refuge that are so much more!
Let’s activate!
Our walk to the main house and visitor center.
The visitor’s center and the main gates to the house were closed, but the grounds were still open to the public. We parked in the area just outside the main gates.
Since I had no idea what to expect on site, I grabbed my Red Oxx Micro Manager field kit that had the Elecraft KX2 and AX1 antenna packed inside.
On this vacation, space in the family car was extremely limited, so I only packed the AX1 and the Chameleon CHA MPAS Lite vertical antennas to pair with the KX2. I left the CHA MPAS Lite vertical in the car assuming I might actually perform the activation back at the parking area once we walked around the main house.
The KX2/AX1 travel kit is incredibly portable and lightweight. That’s the whole kit in the bag in the photo above.
On the air
Turns out, we pretty much had the entire campus to ourselves that day and, as a bonus, there was even an excellent picnic area where I could easily set up the KX2 and AX1 antenna.
I hopped on the air around noon and started calling CQ. I had no internet access on site, but could tell the Reverse Beacon Network and POTA spots page had auto-spotted me because I worked about three stations on CW within the first few minutes.
I started on 40 meters CW, but quickly moved over to phone before converting the AX1 antenna for 20 and 17 meters.
A friend spotted me on the POTA site and I worked a couple more stations on SSB.
After only 15 or 20 minutes on the air, my wife suggested we stay put for a couple of hours. We were all loving the gorgeous weather, wildlife, and beautiful scenery by the pond. She asked our daughters to hike back to the car and grab our picnic lunch. I decided to accompany them and grab the CHA MPAS Lite vertical knowing it would be a much more effective antenna for a longer activation.
The hike was about 30 minutes round-trip (that’s a long plantation driveway!).
After I got back to the site, I installed the MPAS Lite which took all of four minutes. A friend, once again, spotted me on the POTA network and I started calling CQ on 20 meters phone.
I quickly worked stations from Texas, Missouri, Indiana, Massachusetts, New Hampshire, and Ontario.
I wanted to hop back to CW mode though, because I discovered K-0520 (this park) had never been activated in CW before and wanted to give CW hunters a chance to put it in the logs.
I worked stations across the US on 20 meters CW from Tennessee to Kansas, from Arizona, to Alaska, and from Iowa to Ontario. Major fun!
I also decided to head further up the band and work AD1C in Colorado on 15 meters (there were no takers on 12 and 10 meters, but I tried–!).
I started around 17:00 UTC and wrapped things up around 19:15 UTC with 34 logged. That may seem like a low QSO count for over two hours, but a good 45-50 minutes of that time I was off air while hiking back to the car and grabbing the MPAS Lite, setting it up, and enjoying a quick picnic with the family.
All in all it was a very memorable day at the ACE Basic WMA. If you’re ever in the low country of South Carolina, I highly recommend a visit. It’s a stunning site with lots of flora, fauna, hikes, and, of course, a great spot for a little field radio fun!
Note: If I worked you during this activation, it may not show up on the POTA website until I’m home from vacation and can create an ADIF file to submit the logs!
A few weeks ago, I posted a report about doing my first park activation with the Elecraft AX1 super compact antenna. If anything, I felt the activation almost went *too* well using such a small antenna. I didn’t want to give others the impression this is all the antenna you’ll ever need–it’s just a brilliant compact antenna designed for convenience and accessibility. It’s a fun field companion and can be used pretty much anywhere.
Yesterday morning, I had a number of errands to run on the south side of Asheville and had not planned to do a POTA activation. While I was waiting on a curbside delivery, however, I was admiring the nice weather and thinking that I might venture out later in the day to do a Parks On The Air (POTA) activation. Part of me knew, though, that if I returned home, I’d get involved with projects and never make it back out to the field.
I always carry a transceiver and antenna in my car, so I opened the trunk and found my Elecraft KX2 transceiver field kit which included the Elecraft AX1 antenna. Technically, that’s a whole station! Why not give it a go–? I’m always up for a challenge.
Since I would be passing by the Blue Ridge Parkway on the way home, I quickly scheduled an activation on the POTA website via my phone so that the spotting system would know to grab my information from the Reverse Beacon Network (RBN) when I started calling CQ.
Blue Ridge Parkway (K-3378)
I knew this might not be an “easy” activation: I would be using a super compact field antenna that’s quite a compromise in terms of performance, propagation wasn’t exactly stellar, and I was activating a popular (hence somewhat stagnant) park on a Monday morning. Not necessarily ideal ingredients for a successful activation.
I also discovered my phone tripod in the trunk of the car, so decided to make one of my real-time, real-life, no edit videos of the entire successful or failed activation. (Hint: It turned out to be a success.)
If you’d like to accompany me on this park activation, check out my video on YouTube:
At the end of the day, the AX1 continues to impress me. It is a compromise? Yes. Does it perform as well as a resonant wire antenna? No. Can it activate a park as well as my other antennas? Yes.
AX1 QSO Map
Click to enlarge
No doubt, part of my success with the AX1 is because I’m primarily using CW instead of SSB to complete activations. I’ve made SSB contacts with the AX1, but I’ve never completed full park activations with it yet–in truth, though, I’ve never tried.
In fact, perhaps it’s just a lucky streak, but so far the AX1 has been as effective as many of my wire antennas in terms of simply completing valid park activations in less than an hour. My signal reports aren’t as strong as they would be with, say, my EFT-MTR resonant antenna or Emcomm III Portable random wire antenna, but it’s enough to get the job done.
If nothing else, I’ll admit that the AX1 reminds me of the magic of low-power radio each time I use it. When I log stations hundreds of miles away, with such a modest station, I feel like I’ve accomplished something.
In short? It’s fun to use.
Black Friday Sale
FYI: I just received Elecraft’s latest Black Friday 2020 ad and noticed that the AX1 antenna package (which doesn’t include the 40M extension) is on sale. Click here to check it out.
QRP radios, product announcements, reviews, news and more. Low power amateur radio fun!
Please support QRPer by adding us to your whitelist in your ad blocker. Ads are what helps us stay online. All of our ads are ham radio related--no junk, we promise! Thank you!
Last Tuesday (March 2, 2021), I needed to make a quick trip to south Asheville and pick up some gear I had ordered from REI. Of course, I had a hankering to fit in a Parks On The Air activation. I contacted my buddies Eric (WD8RIF) and Mike (K8RAT) and mentioned I might make a visit to the Blue Ridge Parkway [it’s always a good idea to have others look for you in case your unable to spot yourself on the bands].
I also had a first at this activation! I worked ND9M/MM. To my knowledge, I’ve never worked a maritime mobile station at a park activation–certainly not in CW! The map above omits this contact since the location was unknown.
