I carved out a little time on Tuesday, August 24, 2021, to play POTA and take a hike at Tuttle Educational State Forest (K-4861).
Being August in the Piedmont of North Carolina, it was a very humid and warm day. That wasn’t really a problem, though, because Tuttle has so many well-shaded picnic tables.
Once I arrived on-site, I decided to deploy the Chameleon CHA Tactical Delta Loop (TDL) antenna for a few reasons: I thought it might make for some good daytime NVIS action, perhaps even a little fun on the 20M band, and it’s so darn quick to deploy.
With the state of propagation the way it is these days, though, I never know what to expect on the air despite the antenna or my wishes!
Many thanks to Carolanne (N0RNM) who shares the following guest post:
A Booty Boss Micro Radio Kit
by Carolanne Fisher N0RNM
I am a bit of a tinkerer and an aspiring POTA activator, so when I received my Elecraft KX2 a couple of weeks ago with its way-too-big carry bag, I immediately started to think about ways I could keep the KX2 protected on the trail in a much lower-profile, light-weight, and easy-to-carry kit that would always be ready to go. The trick was to find a case of just the right size, with plenty of built-in organization and flexibility to build the kit around. I found what I hoped would be exactly what I was looking for from the excellent Red Oxx Manufacturing company (redoxx.com) — a soft-sided compact bag they call the Booty Boss Waist Pack. At least the specs looked good…
My Booty Boss Micro Radio Kit, packed up and ready to roll. The color isn’t exactly “low-profile,” but I figure there is more than enough black and gray in the world.
I am certain that whoever designed this bag did it specifically with the KX2 in mind. It is small enough to take anywhere, yet it fits my entire setup, including the radio, an extra battery pack, an AX1 antenna, complete with its 40 meter extension coil, 2 counterpoises, along with other necessities perfectly. I printed and spiral-bound a small note pad, shoved in a few accessories, and I was ready to rock and roll. The bag is even lightly padded for a bit of peace of mind. I am a CW-only kind of op so a mic is not a concern, especially since if I absolutely needed to use phone, the KX2’s built in mic would serve perfectly fine.
A peek into the top of the fully packed bag. I replaced the carrying strap that came with the bag with a Red Oxx Claw Non-Slip strap to make a more secure carry.
I tested the bag during several “back-porch activations” and everything seemed to work great. That is until I tried to use it under more realistic conditions — without the shaded picnic table to deploy on and the comfortable chair to sit on. Sitting on a rock while balancing the radio on my knee with its floppy AX1 antenna, and note pad while actually tying to send code proved to be a bit more than I could handle. It was clear that something like a clipboard was necessary to complete the micro radio kit, but a normal-sized clipboard would completely break the one-tiny-bag ethos.
A couple of years ago I designed and 3D printed a portable folding easel to support my sketchbook, watercolors, water etc. when out and about nature journaling or urban sketching. It worked great for that so I made a smaller version, added a recess for the radio and made sure it had room for the notepad. In order to fit in the bag, the size, even when opened to its full 8” x 9.5” size is a bit cramped, but with the addition of a leg strap, like a pilot’s lap desk, it it does the trick.
The complete current contents of my micro radio kit. Total weight: 4.3 Pounds
Here is everything currently in the bag and how it all gets stowed:
Front zip pocket
13’ and 33’ counterpoises for use with the AX1
An extra 28.5’ random wire antenna with 50’ of mini throw line attached (fly fishing backer line with two 1 oz. fishing weights) along with a 17’ counterpoise
Front main compartment
Folded radio desk
Note pad
Pencil
Two small interior pockets
Binder post
Spare KX2 Battery
Interior zip pocket
Spare set of paddles w/ KX2 attachment and cord (by Peter GM0EUL)
Spare pencil
Copy of my radio license
Rear main compartment
Ax1 antenna (whip, 20 and 40 meter coils) lying the bottom
KX2 (fits in the bag with the KXPD2 paddle attached)
Large slip pocket
Ear phones
Kit fully deployed with the KX2 on the custom radio desk.
The KX2 fits flat on its back or up on its kick stand in its custom sized recess. A sticky gel pad (from Amazon) placed in the recess pretty much “glues” the rig to the desk until you want to remove it.
Although I don’t use it all that often, the AX1 is my all-purpose, quick-to-set-up and a snap-to-put-away antenna. I mount the bipod inboard to the radio (over the BNC connection) so it fits on the desk to provide support. I wedge the bipod out from the rig with a spare pencil or a stick from the trail placed between the rig and the front leg to take some of the twist pressure off the BNC connector.
Although the micro radio kit holds everything I need to make contacts, there are plenty of times that I like to have a more luxurious set up — a folding chair and table, my Alex Loop antenna, tripod, lunch, iPad, etc. Or perhaps I’m off for a multi-day and need an external battery, a solar charging system, food, shelter, etc. This scenario is precisely where the micro radio kit really comes into its own. It is tiny enough to slip into just about any bigger bag or placed on the waist belt of a backpack. No more wondering if you remembered this or that bit of radio kit or loosing track of things you borrowed from another kit. If you actually did forget something extra you thought you packed, not to worry, the micro radio kit has everything you need right inside to make contacts.
As a tiny everything necessary, nothing extra radio bag, the Booty Boss micro radio kit is, well, the BOSS!
– Carolanne (N0RNM)
Thank you so much for sharing this, Carolanne! As you know, I’m a massive fan of Red Oxx gear and also own the Booty Boss. It’s simply brilliant that you can even pack a folding radio desk inside! Thank you so much for sharing your field radio kit with us.
As I’ve mentioned a number of times on QRPer and on the SWLing Post, I’m a pack geek. I enjoy organizing and packing my gear for field radio activities and travel.
Last week, I made a very quick overnight trip to visit my parents. My time during this trip was very limited and I did not plan to fit in an activation, but Monday morning, I was able to knock out an errand very early and that freed up a couple of hours in the early afternoon. Fortunately, prior to leaving my QTH, I decided to pack a few travel items in my GoRuck GR1 pack along with a field radio kit built around my Elecraft KX2.
I never leave home without a field radio kit because I never know when an opportunity to play radio might happen.
On the way home Tuesday, I popped Lake Jame State Park and fit in a quick, last minute activation. Moments before arriving at the lake, I received a request from one of my YouTube subscribers asking if I would make the occasional video showing what’s in my radio packs and field kits.
I’ve been meaning to make these videos but, frankly, often forget when I arrive at a park or summit because I’m just a little too focused on starting my activation.
Since I had some overnight items in my pack, it wasn’t a typical SOTA or POTA field kit, but I decided to make the video anyway. After all, I love watching videos about how others pack and organize their radio and travel kits. But then again, I’m a pack geek. I did mention this right–?
Although I’m not always the neatest person (my wife is probably chuckling at this gross understatement), I’m a meticulous and very organized pack geek. What you see in the video is exactly how I pack when no one is looking. 🙂
I’ll add here that if you’re interested in field radio kits and packs, I’d encourage you to check out my Anatomy of a Field Radio Kit series; Part 1 has already been published and Part 2 will be posted later this week. In Part 2, I take a much deeper dive into safety gear I take on SOTA activations.
Gear
In the video, I mention that I would attempt to link to all of the items in my pack. I spent time sorting out links this morning; many links go straight to the pack manufacturer because the packs I use typically have no distributors other than the manufacturer, I have also purchased a lot of the smaller items on Amazon, but many can be found in big box stores like Walmart, Target, Canadian Tire, etc.
If I missed something, let me know in the comments.
Video
Like all my videos, this one us unscripted, made in one take (unedited), and also has no ads:
Out of order…
So this video was made prior to an activation at Lake James last week. I’ve mentioned before that my Internet speeds at the QTH are worse than dismal, but since this pack video was relatively short, I was able to upload it ahead of the activation video (it took 1.5 days to upload this 2GB file).
The activation video will be published in another week or so depending on my access to some proper broadband service.
Any other pack geeks out there?
I would love to share photos, descriptions, and/or a video of how and what you pack for field activations. If you’re interested in submitting a guest post, please do so!
Also, I’d love to hear about your favorite packs and how well they’ve held up with time.
Feel free to comment and thank you once again for hanging out here at QRPer.com!
Many thanks to Pete (WB9FLW) who shares the following announcement from Sunil Lakhan (VU3SUA):
We have a new stock for easy bitx kits. This kit is much improved and has no wiring. The kit is very compact and portable too.
Check out in our store .. Colors available . Black . Black with white panels . Blue with white panels . Add a note for preferred color: https://amateurradiokits.in
Recently, I found myself in an embarrassing situation: I was being interviewed on the Ham Radio YouTube channel Red Summit RF, when someone in the chatroom asked how many HF QRP radios I currently own?
How many…? It dawned on me suddenly that I didn’t know the answer.
Throughout my life as a radio hobbyist, I’ve owned a number of transceivers, but I’ve never owned so many at once as I do currently. Since I was licensed in 1997, I’ve owned up to two or three transceivers at once. But things really started changing for me in 2020. And I blame the Covid-19 pandemic.
Our family loves to travel––but during the pandemic, we were essentially grounded. I keenly missed the travel. So, as I’ve mentioned in previous articles, I turned my attention to more regional destinations––and often took the family along––by activating local parks through the Parks On The Air (POTA) program and local summits through the Summits On The Air (SOTA) program.
As a result of this activity, I also began reviewing and evaluating more and more QRP transceivers––and, if I liked them (as I all too often do) purchased them following the review period.
Fact is, I thoroughly enjoy trying out radios, putting them through their paces and engaging all their bells and whistles; I enjoy shaking up my field activations by employing different radios with different antennas and accessories on each outing . I also enjoy writing up field reports and including activation videos on my blog, QRPer.com. Altogether, radio activation gives me a great deal of satisfaction, as does encouraging others to give it a go.
If you’d like to participate in a contest that balances the playing field between fixed, high-power stations and QRP portable stations, you might take a look at the 2nd annual Portable Operations Challenge.
The POC will take place September 4-5 during three, 4 hour periods. The exchange is very simple: your 4 character Maidenhead Grid Square. You can even combine this event with a scheduled summit or park activation.
This contest even includes prizes for the winners.
The Fox Mike Hotel Portable Operations Challenge is designed to optimize equal operating conditions for portable operating during a contest involving non-portable stations. The scoring allows and encourages regular home-based station operations to take part while offering a handicap-style scoring algorithm to be more equalized for portable stations. The approach is akin to the handicap index in the sport of golf. More difficult courses are scored with a higher slope value, indicating a greater challenge to achieve a normal par score of 72 on that course with a handicap of subtracting strokes for golfers who do not typically shoot as low a score as other golfers. A number of factors go into deriving the slope rating for a golf course but they represent the challenge that the course presents to each participant golfer and the golfer’s capability for playing the course.
The POC aims to make portable operations “on par” with more typical fixed-based operations while preserving the enjoyment of being in a new operating environment. Moreover, fixed-based operators can also easily participate in the action, challenging the handicapped-scoring for portable ops. Can the Super Station contester best the Little Pistol portable operation? If we use a scoring metric that reduces the advantages of fixed stations to that of pure radio sport operating, is there a chance that an efficient portable operator or team can come out ahead of the current winning contest station operators? That’s why this is called the Portable Operations Challenge!
Frank K4FMH
THEORY OF THE CONTEST SCORING FACTORS
Several aspects of fixed (permanent)-station contesting can be stacked in the operator(s) favor when compared to most portable operations. One is the use of greater RF power output. Another is a permanent tower with directional, gain producing beams. A third is that it is easier to have multiple transceivers and operators, allowing for a “per-transmitter production” that yields superior scores. A fourth is the mutual attractiveness for fixed-station ops to work other fixed-station ops and ignore the weaker (especially QRP) signals. The addition of having the full force of Internet communications (when allowed), spotting sources, better ergonomics for operating positions, food/drink conveniences, and climate-controlled shelter all add-up to give “course advantages.”
While some portable operations (an example can be some large Field Day teams) can meet or exceed the advantages to contesting identified above, the vast majority do not.
Our scoring metric equalizes some of these advantages. Four factors are used in scoring each contest operation submission. These are the same regardless of whether it is a single operator or a team of operators, unassisted or assisted through the use of operation spotting. These include:
a. Kilometers-per-watt (KPW). Using the Maidenhead Grid Square, the distance in miles divided by the reported power output in watts for the reporting contest participant.
b. Fixed (permanent) vs Portable operation (favoring portable).
c. Mode of contact: Phone vs. CW vs. Digital (favoring phone over CW over digital)
d. Number of transmitters in use (points X 1/t where t = # transmitters)
The logic underlying this metric is as follows:
The KPW metric will tend to equalize power used as well as antenna gain. The km-per-watt is computed per-contact using the centroid lat-lon of the Maidenhead grid square exchanged during the contact. Favor goes to the greater miles-per-watt which equalizes to some degree the antenna gain, power, and point-to-point propagation conditions. The MPW is the basic contact score. Fixed (permanent) station operators have their resident setup which gives an advantage over portable ops, although a team could replicate a Field Day setting with portable crank-up towers, amps, generators, and so forth. Favor goes to the portable operator. The amount of this multiplier can be adjusted much as a competitive “tuning parameter” in future contests.
All things being equal in a QSO, phone is most challenging, followed by CW and then digital (especially weak signal modes like FT8). Favor goes to phone first, CW second, and digital third.
The more transmitters shape the number of contacts so more transmitters get increasing decrements in the points awarded, regardless of the number of ops. This emphasizes the per-transmitter production rather than just the amount of equipment and number of operators. We are experimenting with what seems appropriate discounts for the number of transmitters in simultaneous so as to render a more equitable competition, favoring sport over equipment.
POC DATES
SEPTEMBER 4-5, 2021
CONTEST OBJECTIVE:
For portable and fixed stations to work as many other portable and fixed stations as possible during the contest
period.
CONTEST PERIOD:
The contest consists of three individual and separate 4-hour periods on September 4 & 5, 2021 UTC.
The sessions are:
Session 1: 0800 – 1159 September 4, 2021 UTC
Session 2: 1600 – 1959 September 4, 2021 UTC
Session 3: 0000 – 0359 September 5, 2021 UTC
Stations may be worked once per band and mode by session for a maximum of 15 contacts between stations per session. Duplicate contacts will be removed without penalty. Scoring will be done by each individual session. Participants may operate one, two or all three sessions. Overall champion will be determined by aggregating scores from the three separate sessions. The Individual with the highest aggregated score will be crowned Grand Champion. The single station with the longest distance in KM per watt will be the Distance Champion.
BANDS:
80, 40, 20, 15 and 10 meters
MODES:
CW, Phone (SSB), and Digital
Digital mode is any data mode that can transmit the required contest exchange. Cross mode contacts are not permitted.
EXCHANGE:
4-character Maidenhead grid square
SCORING:
Total score for the session is the sum of all QSO Values.
I have been a fan of QRP operating since I got licensed in 1983. The sticker in the picture is a joke a good friend who is not into CW or QRP, so I include it in my field pictures.
My interest in ham radio had reached a point I was getting away from the hobby. In 2020, I learned about Parks on the Air (POTA) and Summits on the Air (SOTA). I got hooked on activating parks and summits, and now I mostly do QRP CW, much like Thomas Witherspoon, K4SWL does.
Over the past year, I’ve been refining my antennas and radios in the field. I have different radios and antennas for different reasons, and to just mix it up a bit. Occasionally, I will take my IC-7100 or IC-7300 out into the field with my Bioenno 20aH battery, if I’m not planning to hike or go far from the parking lot, or if the bands are just not cooperating.
Back in November 2020 I had my left knee replaced so I had lots of down time and made an important purchase for field activities – an IC-705. It is fantastic and does everything I want it to do without a lot of wires. I’ve also owned and sold within the past 18 months a Yaesu FT-891 (which I sold when I got the IC-705) and had both the Xiegu G90 and X5105. I would expect one day to get another FT-891 as it has amazing filtering and pulls in weak CW signals better than any radio I’ve owned. The G90 and X5105 are okay, however I was not impressed with the G90 from the start for out in the field. There were just too many wires in order to set up and use with my portable laptop computer if I was taking that along.
The X5105, which I had high expectations for, disappointed me in the fact that storing and using CW memory keying is not user friendly. The nice thing about that radio is, no microphone, no problem, I had some success using the 5105 and got great audio reports.
I’ve been looking ahead to my projected retirement and hopes of through hiking the Appalachian Trail in 2026. Although the IC-705 is an excellent field radio, all mode, VHF/UHF/D-Star/HF/6 meters, I already know for a 7 month hike from Georgia to Maine, it will just be too bulky in my backpack. I have heard really good things about the QCX-mini, however I’m an appliance operator and not good with kit building and soldering.
I saw there are options to purchase an assembled QCX-mini, so I decided to check out a 40 meter radio. It took about 2-1/2 weeks before it arrived at my QTH on Saturday afternoon. I hooked it up to one of my HF antennas in my yard used for my IC-7300 that was resonant on 40 meters. I had to use my Heil headset in order to hear the audio, plugged into the 3.5 mm jack. I used my CWMorse paddle and tuned around the band. I called CQ several times before finally I heard WA0USA in Palm Beach, FL calling CQ. I called him and got a 579 report and he was a solid 599. We chatted for about 10 minutes, and he was running a kW while I was using 5 watts. It felt good to know that I was being heard.
Sunday morning I had time to go activate a local park (K-1418) before some afternoon commitments. I had also recently purchased a link dipole for 20/30/40 meters off eBay from N9SAB. I had tested this antenna out a couple of times last week, so I wanted to pair it with the QCX-mini. I went with little expectations about the little mini, so I also packed my IC 705 just in case I needed it to complete my 10 contacts to have a successful activation. To my surprise, I spotted myself on the POTA page, and in 45 minutes I had a total of 26 QSOs in my HAMRS log! It was amazing and I think I found the perfect combination for true lightweight, portable operations.
I was so impressed with this activation that last night I ordered the 20 meter QCX-mini! These can be ordered from qrp-labs.com and they have a lot of other kits available as well. The kit itself is $55, and I opted to have it assembled ($45) and purchased the enclosure ($20).
This little radio is very user-friendly. I was able to easily access the menus, customize it to my liking, including the paddle, preset frequencies, several stored CW memories, and was on the air calling CQ Saturday evening without seeking out the instructions.
I had mentioned previously about my disappointment with the Xiegu X5105 and not being able to easily store and recall memories. Not a problem at all with this little radio. I enabled the decoder feature just to test it out, and it decodes better than the G90 or X5105, including very weak signals. The size is a fraction of the size of the X5105 and total weight for everything, including the Bioenno 12v 3aH battery is less than 2 pounds and it all stores very nice.
These quick videos were taken this evening before storms hit; that’s why you will hear lawnmowers in the background. I wanted to first show a demo of the receive decoder and how well it decodes even weaker signals:
My biggest complaint about the X5105 was how the memory was next to impossible to use. I do a quick demo how to access a stored message and send it over the air. I also have it set to repeat every 6 seconds:
I did make a couple of changes to the radio setup. I did not like having to use the headset, so I went on Amazon and purchased a mini portable 3 watt mobile phone speaker line-in speaker with 3.5mm audio interface (affiliate link). That cost under $15 and works extremely well. It has a built in charger that plugs into a micro-USB to charge the battery when not in use. I also have a cell phone holder that fits perfectly on my Neewer stand I purchased several months ago for my IC 705, and it sits nice and firm on the table. I may not take that to the field if I’m doing a lot of hiking.
Here are some other details about the QCX-mini from their website:
The Optional enclosure is black anodized extruded aluminium, very sturdy and elegant. The enclosure size is 95 x 63 x 25mm without protrusions. The top and side panels are drilled and cut to match the QCX-mini with laser-etched lettering. The enclosure includes four self-adhesive feet.
Special portable-friendly features:
Small size: 95 x 63 x 25mm enclosure (plus protusions)
Low current consumption (for example 58mA receive current, with 12V supply and display backlight off)
Low weight, 202 grams
Sturdy extruded aluminium enclousre
All-metal BNC short connector, bolted to enclosure
List of features:
Easy to build, two-board design, board with main circuit and connectors, display panel board with LCD; all-controls board-mounted on a press-out sub-board. No wiring, all controls and connectors are board-mounted
Professional quality double-sided, through-hole plated, silk-screen printed PCBs
Choice of single band, 80, 60, 40, 30, 20 or 17m
Approximately 3-5W CW output (depending on supply voltage)
High performance receiver with at least 50dB of unwanted sideband cancellation
200Hz CW filter with no ringing
Si5351A Synthesized VFO with rotary encoder tuning
16 x 2 yellow/green LCD screen
Iambic keyer or straight key option included in the firmware
Simple Digital Signal Processing assisted CW decoder, displayed real-time on-screen
On-screen S-meter
On-screen real time clock (not battery backed up)
Full or semi QSK operation using fast solid-state transmit/receive switching
Frequency presets, VFO A/B Split operation, RIT, configurable CW Offset
Configurable sidetone frequency and volume
Connectors: 2.1mm power barrel connector, 3.5mm keyer jack, 3.5mm stereo earphone jack, 3.5mm stereo jack for PTT, 3.5mm stereo jack for CAT control, BNC RF output
Built-in test signal generator and alignment tools to complete simple set-up adjustments
Built-in test equipment: voltmeter, RF power meter, frequency counter, signal generator
Beacon mode, supporting automatic CW, FSKCW or WSPR operation
GPS interface for reference frequency calibration and time-keeping (for WSPR beacon)
CAT control interface
Optional 50W PA kit
Optional aluminium extruded cut/drilled/laser-etched black anodized enclosure
Just a quick note on the link dipole. It is well made and I had a 1:1 SWR on the CW part of the band, which is perfect. I did put the IC 705 to work when I attempted to work a couple of SSB stations on POTA, and at 7.235 the SWR was only about 1.3:1, so minimal loss. Check out the N9SAB antennas on his eBay site. His shipping is very quick. I took a picture of the balun with the included choke in the package I purchased, and the second picture is the link between the 20 and 40 meters. It works great.
I mentioned my goal about hiking the Appalachian Trail in 2026. I’m sure there will be other multi band mini size radios available by then and I’m hopeful QCX will have one in 5 years for me to use. My goal is to activate summits along the way while taking breaks from the hiking, or at night before calling it an evening. Since I’ll be on the A.T. I’ll also have lots of opportunity to activate POTA as well. Most thru hikers are not hams and they are always concerned about no cell phone coverage. I won’t have that issue and I’m confident I’ll be able to be in touch with other hams throughout the journey.
Thank you once again Tom for allowing me to post on QRPer. I think I finally have a QRP radio that you have not tested or purchased yet. I hope your readers find this short article useful.
73
Scott – KN3A
Scott Lithgow (KN3A) is a regular contributor on QRPer.com. Click here to check out his previous posts.
It’s funny: when I started my POTA journey in earnest during February 2020, I plotted out all of the state parks in the part of western North Carolina where I travel the most.
At the time, POTA had only a wee fraction of the community it does now and many of the parks and game lands were still ATNOs (All-Time New Ones)–parks that had never been activated. Fort Dobbs was still one, in fact, and I had marked it on my POTA game plan spreadsheet.
My mission back then was to rack up unique-to-me parks as I explored the region; in doing so, I ticked off quite a few ATNOs. It was fun!
I focused on parks a little further afield first. This provided me with a sense of adventure and travel during the first round of Covid-19 lockdowns.
At the end of 2020, I realized I had never activated Ft. Dobbs State Historic site which was, ironically, one of the lowest hanging fruit sites around. It’s only, perhaps, 30 minutes from where I travel each week.
I suppose Fort Dobbs has been “out of sight, out of mind” until I saw a tweet from Andrew (N4LAZ) who activated Dobbs on August 6, 2021. I mistakenly assumed that the only spots to set up on site were around the periphery of the parking lot. This time of year, in the middle of the hot and humid summer? I’m less enthusiastic about open parking lot activations.
Andrew mentioned that the site actually has an excellent covered picnic area where he was allowed to perform his activation.
That’s all I needed to know!
Fort Dobbs State Historic Site (K-6839)
On Tuesday, August 10, 2021, I traveled to Fort Dobbs State Historic Site and quickly found the covered picnic area Andrew had mentioned. It was, indeed, ideal for POTA!
Firstly, I must say that I really do enjoy reading the postings on your website!
I wonder if you or any of you colleagues can help me with the connections for the mAT-40 ATU?
It comes with connecting control cables for Yaesu, ICOM, etc but I want to control it manually, remotely, with home built QRP transmitters. I want to make a small control box similar to that with the CG-3000 auto ATU ( the great advantage of the mAT-40 is that it will tune with less than 1 watt input)
Many thanks in anticipation 73 John G1AWJ
Readers, if you have any advice for John, please comment! Unfortunately, I’ve no experience with the mAT-40. Click here to comment!
As I mentioned in a previous post, I do love rotating out radios I take to the field. Shuffling radios not only helps me remember a radio’s features and menu system, but it helps me understand any advantages one radio might have over another.
One radio I use at the QTH a lot is the Mission RGO One. I reviewed this radio for The Spectrum Monitor magazine, and later posted the review on The SWLing Post. It has been a few months since I posted a field report and video using this rig yet it’s one readers ask about all the time because this is a small production run radio.
Before heading out to Lake Norman State Park on August 9, 2021, I grabbed the Mission RGO One, the Chameleon CHA LEFS sloper, and my 15Ah Bioenno LiFePo4 battery. I knew this combo would serve me well as propagation that day was in the dumps!
Lake Norman State Park (K-2740)
Lake Norman is such an effortless park to activate. They’ve a huge picnic area, large trees (for both antenna support and shade!), and are typically not incredibly busy during the week. I love Lake Norman because they also have a very nice Lake Shore Trail I enjoy hiking post-activation.
That Monday morning, as I drove to the park, it was approaching lunch time and I did worry that some of my favorite picnic spots might be taken, but when I arrived, I was happy to see I pretty much had the place to myself!
Setting up the CHA LEFS sloper antenna takes a couple minutes longer than a standard end fed antenna only because the feed point is elevated and the radiator slopes down from the feed point. Since I typically do activations on my own (with no extra hands to help), I find that a little extra antenna prep equates to a quicker overall deployment.
My procedure for deploying the CHA LEFS
The CHA LEFS sloper
First thing I do is identify a good tree limb at least 45′ or so high and also identify an unobstructed path for the sloping radiator to travel.
Prior to hoisting the antenna, I stretch out the radiator and attach it to a tree or support (using the supplied paracord) in the direction I want the slope to follow.
I then use my arborist throw line to snag the desired tree limb and I connect the end of the throw line directly to the CHA LEFS’ feed point. Chameleon provides Paracord for hoisting the antenna, but the great thing about the arborist throw line is that it’s more than strong enough to handle this job. It saves the extra step of pulling paracord through the tree.
Next, I attach a 50′ length of coax (PL-259s on both ends) and stretch the coax out in the opposite direction of the CHA LEFS radiator. Doing this keeps the antenna from spinning and tangling the radiator and coax as it’s hoisted into the tree.
Finally, I simply pull the throw line and raise the antenna feedpoint to the desired height. Again, I like a height of at least 40-45′, but lower will still work. As I raise the antenna, I do put a little tension on the coax feedline just to keep it from swinging around the throw line or radiator.
Of course, if you have two people, one person can simply stretch the coax as you’re raising the antenna feedpoint which will also keep it from tangling.
That’s all!
In truth, the amount of extra time to deploy the CHA LEFS as opposed to, say, an end-fed half wave is maybe three minutes.
I picked the Mission RGO One because it has an amazingly quiet receiver and handles QRN like a champ. Plus, being a tabletop radio, it also sports a proper speaker, large controls, and up to 50 watts of output power if needed.
Although I’m a QRPer, on days with horrible propagation, I have been known to increase the power beyond 5 watts if operating SSB especially. This year, I set out to validate all of my park and summit activations with 5 watts or less, so at least my first ten contacts at a park will be QRP.
I thought I’d start by calling CQ on the 40 meter band in CW. Within 15 minutes, I snagged the ten contacts needed for a valid POTA activation. I was very pleased with this.
Since I had mobile phone service, I checked the POTA spots and worked AA3K (Park To Park) then moved to the phone portion of the 40 meter band.
During the exchange with AA3K, I did pump the power up to a cloud-scorching 20 watts! A proper rarity for me.
I then worked an additional five contacts in about 8 minutes in SSB. Very satisfying!
QSO Map
Here’s my QSO map of the entire activation. The red polylines represent SSB contact, the green are CW:
I was very pleased with the results especially after reading reports from other activators that same day who really struggled to get their ten.
Video
Of course, I made one of my real-time, real-life, no-edit videos of the entire activation. If you’ve never seen one of my videos before and have a strong dislike of professional, well-polished YouTube channels, you’re in for a treat! 🙂
Post-activation–and despite the heat and humidity–I hiked the length of the Lake Shore Trail; roughly six miles. I highly recommend this trail if you can fit it into your schedule.
Thank you!
As always, thank you for reading this report and thank you to those who are supporting the site and channel through Patreon and the Coffee Fund. While certainly not a requirement–my content is always free–I really appreciate the support.
Here’s wishing everyone a little radio fun this week!
QRP radios, product announcements, reviews, news and more. Low power amateur radio fun!
Please support QRPer by adding us to your whitelist in your ad blocker. Ads are what helps us stay online. All of our ads are ham radio related--no junk, we promise! Thank you!
I carved out a little time on Tuesday, August 24, 2021, to play POTA and take a hike at Tuttle Educational State Forest (K-4861).
