On Monday, October 4, 2021, I was set to have a lunch with my good friend, Taiyo, who happened to be in town from Japan. We decided to grab some take-out and meet at a picnic area halfway between my QTH and where he would be staying during his visit. Turns out, the Vance Birthplace (K-6856) fit the bill perfectly–especially since rain showers were in the forecast all day and Vance has a covered picnic area.
I didn’t have an activation in mind that Monday because my focus was on spending time with a friend I hadn’t seen in years, but I brought the KX2 field kit with the AX1 antenna…you know...just in case.
Radio time!
After running a number of errands in town and grabbing some take-out lunch from Whole Foods market, I still ended up arriving at Vance about an hour early, so I pulled the KX2 and AX1 out of the car.
On Monday, September 27, 2021, I had just enough time to stop by the Blue Ridge Parkway on my way back from Asheville, NC and fit in a short activation.
I had my Xiegu X5105 along for the ride and decided to pair it with the MFJ-1984LP EFHW since I knew propagation was going to be rough.
That day, Earth was being pounded by CMEs and, frankly, I didn’t know how pleasant it would be on the air.
I picked one of my favorite spots along the Blue Ridge Parkway: a grassy hill I’ve used numerous times in the past. I love this particular site because it’s incredibly rare that anyone else parks or walks there, so I can set up larger wire antennas and not have to worry about others walking into the radiator or tripping over the counterpoise.
On the morning of Thursday, September 23, 2021, I had one thing on my mind: SOTA!
It had been well over a month since my last SOTA activation and I was eager to hike to a summit and play radio.
It had been raining for a few days but overnight, a front moved into the area that swept out all of the clouds. We were finally feeling proper fall weather.
It was gorgeous outside and I made up my mind I’d fit in a summit activation.
I was visiting my parents in Hickory, NC, so I knew I’d have to drive a bit to activate a unique (to me) summit. On top of that, I knew I’d be alone and trails would be very muddy after days of rain. I decided to stick with an easy hike, so picked Flat Top Mountain (W4C/EM-026) off of the Blue Ridge Parkway.
I announced my activation via the SOTA website and drove about one hour to the trailhead of Flat Top Mountain.
Aborted!
As I drove up US321 to Blowing Rock I noticed that clouds were hangin over the mountains. In the foothills, it was blissful: clear skies, sunshine, dry air, and quite cool. As I drove up the Blue Ridge escarpment, it started getting a little gusty outside–I realized that the mountains were still on the edge of the cold front. Continue reading SOTA Plan B: An aborted activation followed by an amazing (although gusty) alternative!→
Many thanks to Steve (MW0SAW) who shares the following video of DL1DN making a very enthusiastic contact with VK5MAZ–Germany to Australia–QRP SSB pedestrian mobile:
What an amazing accomplishment! I think I felt as excited as David did in his video. The reception of VK5MAZ was simply phenomenal, too!
uSDR clones
David (DL1DN) mentions at the end of his video that he had been in touch with Manuel (DL2MAN) who is the designer of the incredibly affordable uSDR transceiver project. David had featured a Chinese clone version of the uSDR in some of his previous videos. These days, it’s difficult to know if you’re ordering a clone or the original item because often the clone so closely mimics the original.
As I understand it, the uSDR is completely open source and, at least at time of posting, there is no comprehensive kit version available. However, all of the information needed for gathering parts and building the uSDR are public and free.
Manuel (DL2MAN) made the uSDR project open source with the condition that it cannot be used for commercial purposes (in other words, produced by another party and sold as a product). Of course, it was very quickly cloned by manufacturers in China and is now available on eBay.
David shared a link to Manuel’s recent video speaking about the differences between the two units:
You’ll note that I try to steer clear of clones on QRPer.com. I do this mainly because I like supporting the original developers and designers of radios and kits when possible. I feel like by doing this, I’m supporting the innovators in our community as opposed to taking money away from them.
On that note, I’m in the market for an M0NKA mcHF transceiver!
UPDATE 09 (Oct 2021): Larry (N0SA) informs me that he sold all of his SOTA Paddle inventory as of last night. In other words, very quickly. If he produces another run of them, I’ll post it here on QRPer.com!
A couple weeks ago, Larry (N0SA) reached out to me and asked if I’d like to evaluate a new set of precision field paddles he’s designed. Having purchased a set of 3D-printed paddles from N0SA last year, I didn’t hesitate.
Larry simply calls this model the SOTA Paddle. An appropriate name because this paddles is incredibly compact, lightweight, and perfect for hiking and backpacking. They also have a short Allen wrench cleverly stowed within the paddle body for any adjustments in the field. The Allen wrench is locked in in such a way, there’s no possibility it’ll fall out either. Clever!
They come with a high quality three foot cloth braid cord with molded 1/8” plug.
Over the past week, I’ve taken these paddles to two different park activations with the Elecraft KX2 and AX1 antenna.
My activation videos and field reports are perhaps a week down the road yet, but I couldn’t help but post my initial impressions.
So how would I describe N0SA’s new SOTA Paddles–?
The Bee’s Knees!
I love them.
These truly feel like precision paddles. They’re entirely constructed of aluminum and stainless steel parts.
Although the body/frame of the paddles are open, they feel incredibly sturdy. No doubt, they’ll survive the environment inside a backpack or field kit.
They’re very compact, yet feel perfect in the hand.
Larry also includes 6 pieces of 3M dual lock for mounting the paddles on a clipboard, radio, or any other surface.
As readers know, I love my CW Morse Paddles–they represent an amazing amount of quality at such an affordable price.
If you’re in the market for a compact precision aluminum key, however, I can recommend these without hesitation.
Here’s the deal as I understand it: Larry may only make a couple small production runs of these. He does this as a fun side hibby, not for scaled-up production and distribution. I believe he may have as many as 20 units available soon.
Again, you’ll see the SOTA Paddles in action in upcoming videos, but I wanted to mention it here on QRPer so that–if this sort of thing interests you–you might have a chance to place an order before the first and/or second production runs are spoken for.
The price is $125.00 US (each) plus $15.00 for priority mail shipping. You’ll have to inquire if located outside the US (I’m not certain if he ships internationally).
Payment can be made via PayPal to his email address which is his callsign @att.net. (You can also check out his contact details on QRZ.com.)
Email him with questions and to check availability in advance.
Larry is a long-time reader of QRPer.com, so he might add notes in the comments section.
Speaking of which, thank you so much, Larry, for sending me these paddles. They are simply amazing.
On September 20, 2021, I had a full day planned in town. It was one of those days where my few errands and appointments were spread out across the day in such a way that driving back home between appointments made no sense. I knew I might have a bit of time to kill.
The big appointment holding me in town was recall service work on my Subaru that would take most of the day. The dealership reserved a loaner car for me.
That morning, I cleaned out my car (removing a couple of radios and antennas) and I packed a backpack with the supplies I’d need for the day; water, sandwich, laptop, and (fortunately) my Elecraft KX2 and AX1 antenna.
I would take this pack with me in the loaner car as I ran my other errands. I remember thinking that there was likely no possibility of doing an activation–it was rainy and I knew even getting set up at the service center might take an hour. I packed the Elecraft gear nonetheless. (Never leave home without a radio, I say!)
That morning, I drove to the Subaru dealership and–long story short–the service work had to be cancelled. While I wasn’t happy that I’d made the early morning trip to the dealership for nothing, this did essentially free up a good portion of my morning to play radio. Even though I had my own car for the day, I had completely emptied it of radio gear, so the KX2 and AX1 were truly all I had. Continue reading Elecraft KX2 and AX1: Seriously…how effectively can such a compact field kit work?→
The Blue Ridge Parkway is one of the easiest POTA sites for me to activate when I’m at the QTH.
Pretty much anytime I head into Asheville from home, I’m going to cross the parkway. The BRP is such a refuge, I often take it to avoid hitting the Interstate or a busy highways. It takes longer, but it’s orders of magnitude more peaceful and pleasant than, say, Interstate 40.
On Monday, September 13, 2021, I had a small opening in my schedule in the afternoon and decided to pop by the Folk Art Center for a quick picnic table activation since I was passing by.
The Folk Art Center is a site where I typically deploy smaller, lower-profile antennas to keep from interfering with others who are enjoying the park. I try to keep my antennas very close to my operating spot and my counterpoises on the ground in a space where others aren’t likely to tread.
In the past, I’ve used the Wolf River Coils TIA, the Elecraft AX1, Chameleon MPAS Lite & MPAS 2.0, and once, a Packtenna 9:1 UNUN random wire. I avoid anything that slopes so that I don’t inadvertently “clothesline” unsuspecting vacationers!
One of the closest parks to my parents’ home in Hickory, North Carolina (where I travel most weeks) is South Mountains State Park.
Despite its convenient location, I haven’t activated South Mountains many times and, in fact, the times I have activated it, I’ve always found it a struggle to log the ten contacts needed for a valid park activation. I suspect it’s had less to do with the physical location of my operating spot (which has admittedly been in a bit of a “bowl” surrounded by hills) and much more to do with the fact that propagation has been crappy on the days I tried to activate.
Ironically, I’ve activated the adjoining South Mountains Game Land numerous times with wonderful success. It’s funny how that works.
South Mountains State Park (K-2753)
Max (WG4Z) set up the CHA TDL.
I had a good reason to hit South Mountains on September 9, 2021. My buddy Max (WG4Z) had just purchased an Elecraft KX3 at the Shelby Hamfest (at an incredible deal, I might add). He plans to pair it with a Chameleon CHA TDL (Tactical Delta Loop) he has on order.
Sometimes we do things that take us outside of our comfort zone.
That’s exactly what I did on September 8, 2021 at Tuttle Educational State Forest (K-4861).
My friend, Jérôme, asked I would consider doing a POTA activation video in French!
Jérôme lives in France and wants to do a POTA activation there eventually, but had a number of questions about what to do in the field (spotting, logging, etc.). He’s been watching my videos for a while but admits that while he can understand written English (with the aid of Google Translate), he doesn’t understand spoken English.
Although I regularly listen to news and YouTube videos in French, it’s been ages since I’ve spoken French for any extended period of time.
Jérôme has been bugging me about the French video for some time, actually, but I’d put it off because there were a number of radio terms I simply never learned when I lived in France (well before I was a ham radio operator).
When he very diplomatically asked me again via email on the morning of September 8, I thought, “Why keep waiting? Just do it!”
After completing a successful activation at Fort Dobbs State Historic Site on Wednesday, August 25, 2021, I decided to fit in one more activation that day. I thought about heading out to one of the game lands I hadn’t hit in a while, but frankly, I needed a park a little closer to home due to my time constraints that day, so Lake Norman State Park it was!
Lake Norman State Park (K-2740)
Lake Norman is such an effortless park to activate. Their main picnic area has numerous tables (including two large covered areas), and tall trees providing support for antennas and much needed shade from the NC summer sun!
One thing I had not decided upon was what antenna I’d use at Lake Norman. Earlier, I used my trusty speaker wire antenna at Fort Dobbs, but I like to shake things up. I checked the trunk of my car and found the Chameleon MPAS Lite. Seeing how propagation plummeted after my previous activation, I decided that I wanted a large wire antenna deployed rather than a vertical.
The MPAS Lite can be configured as a wire antenna, of course: instead of attaching the 17′ whip to the “Hybrid Micro” transformer, you attach the 60′ wire that might normally be used as a counterpoise.
Setting it up was quite easy, in fact. I used my arborist throw line to snag a tree branch about 45′ high, then attached the throw line to the floating dielectric ring on the Chameleon wire spool. I stretched the entire length of wire out, attached the end to a tree, then hoisted up the center, forming an inverted vee shape.
Wire antennas are so low-profile and simply disappear in trees.
Even thought the 50′ coax shield would act as a counterpoise, I really wanted another ground wire attached, so I pulled one of the wires off of my speaker wire antenna and attached it to the grounding post of the MPAS Lite’s stainless spike. I figured a little extra counterpoise wouldn’t hurt.
Although I’d never used the CHA MPAS Lite quite like this, I was pretty confident my Elecraft T1 would find a match. The Chameleon transformer (the Hybrid Micro) brings most any (but not all) lengths of wire within reasonable matching range of an ATU.
I started on 40 meters and found that, without employing the ATU, I had a match that was slightly below 2:1. Not terribly surprising since I had a good 60′ of wire in the tree. Still, I hit the tune button on the T1 and easily achieved a 1:1 match.
I will add here, though, that perfect 1:1 matches are not that important–especially at QRP levels. I’m certain the TX-500 would plug along with a match of 2.5:1 or higher and still radiate perfectly fine. I’ve known hams that truly equate that 1:1 match with an antenna that’s performing efficiently, but that’s not always the case. Keep in mind a dummy load will give you a 1:1 match but is hardly efficient. The ATU’s job isn’t to make the antenna radiate better–it’s to match impedance.
The CHA MPAS Lite will get you within matching range across the HF bands and, many times, it’s close enough that an ATU isn’t really needed.
I started calling CQ POTA on 40 meters and within 28 minutes had logged the ten contacts needed for a valid park activation–all with 5 watts, of course. I was very pleased with these results because, as I had suspected, the bands were still pretty darn rough.
I then moved up to the 30 meter band where I worked a couple of stations and then, for fun, found a match on 80 meters and worked one NC station (possibly on ground wave!).
Here’s a screenshot of my logs from the POTA website:
I must say that I do love using the Discovery TX-500. It’s such a brilliant little field radio. I’m just itching to take it on another SOTA activation soon!
I’m also loving the TX-500 field kit that I built around a Red Oxx Micro Manager pack.
I used the same bag (different color) for my KX2 NPOTA field kit in 2016. It’s such a great size and can even easily hold my arborist throw line along with all of the station accessories and rig, of course. I’ve made a short video showing how I pack it and will upload that video when I have a little bandwidth!
Video
I did make a real-time, no-edit video of my entire Lake Norman activation. Feel free to check it out below or via this YouTube link. No need to worry about ads popping up–my videos have no YouTube ads!
A Brief Public Service Announcement…
If I have a little advice for you this week, it’s this: don’t wait to play radio because someone says you don’t have the right gear for the job.
I received an email this morning from a ham that’s new to field operation and just received an antenna he had ordered. He was upset because a YouTuber claimed his antenna was basically a dummy load. To add insult to injury, he also found a blogger or YouTuber was also highly critical of his recently-acquired Yaesu FT-818. [Note that the FT-817ND–the 818’s predecessor–is one of my favorite field rigs.]
Keep in mind that many of these YouTubers are trying to produce “click bait” videos that will stir up a reaction and, thus, increase their readership numbers which will have a direct and positive impact on their ad revenue. It’s a red flag when someone doesn’t have real-world examples and comparisons proving their points and typically a sign that they’ve never even used the products in question.
I’ve been told antennas I use don’t work, yet I’ve snagged some incredible QRP DX with them. I’ve been told that some radios I use are junk, yet I’ve hundreds of successful field activations with them. And funniest of all are those who tell me that QRP is ineffective and–quoting from an actual message recently–“a complete waste of time.”
My advice is to simply ignore these folks. The proof is in the pudding! Get out there and play radio! In the words of Admiral Farragut, “Damn the torpedoes. Full speed ahead!”
Thank you!
As always, thank you for reading this field report and a special thanks to those of you who are supporting the site and channel through Patreon and the Coffee Fund. While certainly not a requirement–my content is always free–I really appreciate the support.
Connecting an international community through low-power field radio adventures.
Please support QRPer by adding us to your whitelist in your ad blocker. Ads are what helps us stay online. All of our ads are ham radio related--no junk, we promise! Thank you!
On Monday, October 4, 2021, I was set to have a lunch with my good friend, Taiyo, who happened to be in town from Japan. We decided to grab some take-out and meet at a picnic area halfway between my QTH and where he would be staying during his visit. Turns out, the Vance Birthplace (K-6856) fit the bill perfectly–especially since rain showers were in the forecast all day and Vance has a covered picnic area.
