Category Archives: QRP

Speaker Wire SOTA & POTA: Another rendezvous with Rendezvous Mountain!

I get a little thrill out of checking out new parks and summits.

When going to a new-to-me site, I typically do quite a bit of research in advance. With parks, I look up directions to the entrance, hiking trails, park boundaries, and try to sort out the best potential activation sites on a map. With a summit, it can be much more complicated, but reading previous activator notes really saves a lot of headache. That’s especially the case here in the States where many summits are on private/gated land and/or could require bushwhacking off trail with no mobile phone service.

Then again, returning to a site I’ve been to before is also quite nice. I know what to expect and that often opens up the door to more confidence with time planning, antenna choices, and what to pack in terms of gear.

 

On Friday, March 25, 2022, I re-visited a site I hadn’t been to in nearly a year: Rendezvous Mountain Educational State Forest.

 

What’s great about Rendezvous is that it’s both a POTA and SOTA site.

On top of that (no pun intended) the activation zone of SOTA summit 2543 (W4C/EM-082) is on a road where Rendezvous Mountain Educational State Forest (K-4859), and Rendezvous Mountain State Game Land (K-6941) overlap. One activation yields two parks and one summit!

Last year, it took a bit of research to make this discovery. I studied both the park and game land maps, then compared those with a Cal Topo map. If interested, check out that field report here.

Rendezvous Mountain

I arrived on site around 12:45 local. The park was void of visitors–I almost felt like I’d arrived on a day when the gates should have been closed.

As I grabbed my SOTA backpack out of the back of the car, a ranger pulled up in his truck and  asked if I was planning to hike. I told him about my plans and asked if it was okay that I hike the forest service road to the summit. He said, “Sure. But when you reach the prison crew doing brush cutting on the road, make sure one of the guards sees you before you attempt to pass them.”

Okay then.

I thanked him and double checked that it was actually not a problem to hike the road and he said, “Go for it!” Continue reading Speaker Wire SOTA & POTA: Another rendezvous with Rendezvous Mountain!

Brooks’ first Parks On The Air (POTA) activation

A few weeks ago, I received an email from Brooks (KO4QCC), a newly-minted  ham radio operator who asked to tag along on one of my POTA field activations. 

Brooks, it turns out, lives within spitting distance of a number of parks I regularly activate here in western North Carolina. He mentioned he was interested in observing an activation to learn a bit about deploying a field radio kit and, of course, to learn what it’s like to be on the air.

Brooks was also plotting the purchase of his first field radio kit and was very interested in the Icom IC-705 and MFJ-1988LP End-Fed Half-Wave (EFHW) antenna. 

Of course, I welcomed him to join me but since we both have busy family lives–and my schedule especially took some twists and turns in March–it took a few weeks before our schedules aligned.

I asked Brooks if he would consider actually doing the activation himself instead of simply observing or tag-teaming it.  I’m a big believer in hands-on radio time.

Brooks loved the idea!

On Sunday, March 27, 2022, a window of opportunity opened in our schedules and we agreed to meet at Tuttle Educational State Forest (K-4861). I packed my:

As I’ve mentioned before, I’m not really a “YouTuber” so I’m not actually inclined to capture every moment on video, but it struck me that others may appreciate experiencing (vicariously) what it’s like to do a park activation for the first time.

Prior to meeting, I asked Brooks if it would be okay if I made a video of his activation adding that there was absolutely no pressure to do so–just a thought. I’ll be the first to admit that if I were in his shoes, I’m not sure if I’d want a camera capturing my first activation jitters for all to see. 

Brooks loved the idea–as he, too, saw value in this sort of video–so I brought my camera along for the ride.

In the same spirit, I asked Brooks if he would write up the field report and he wholeheartedly agreed, so I’ll turn it over to him now: Continue reading Brooks’ first Parks On The Air (POTA) activation

Guest Post: Fraser Activates Ben Newe Despite the Winter Weather

Last week, while browsing Twitter, I scrolled past a short note and photos from Fraser (MM0EFI) describing his recent activation of Ben Newes in NE Scotland. I’m not sure if it was the snow, the KX2, or his vintage Land Rover (or all of these) but I wanted to know more about this activation.

Fraser kindly agreed to share the following field report for us here on QRPer.com: 


Ben Newe SOTA Mini-adventure

by Fraser Wenseth (MM0EFI)

Introduction

I’ve lived on the eastern edge of the Cairngorms National Park in north east Scotland for around six years. I’ve always climbed the hills, winter and summer, enjoyed rock & ice but now just love being outdoors. I’ve held an amateur radio licence for 18 years but have to admit that until I discovered Summits on the Air (SOTA), my licence was under utilised!

SOTA has allowed me to discover local hills that I had previously driven by on countless occasions on my way to bigger adventures, or so I thought, because it’s possible to have amazing adventure on smaller hills just by picking the time of day, season, or even choice of radio gear. Sometimes I’ll just carry VHF gear, which is always a challenge in a rural area! Of course I still love a big day out in the mountains, but todays story concerns a little hill just 7 miles from my home in Royal Deeside.

It’s called Ben Newe and its’ SOTA reference is GM/ES-053. It stands 565m or 1853’ above Strathdon in Aberdeenshire. I’d planned on climbing it after work. Generally I work a really early shift one day a week and the motivation for getting out of bed at 0340 is knowing that I’ll generally be on a summit around 12 hours later.

I left for work at 0400 (British Summer Time, UTC+1) and that’s when the snow started falling. It actually didn’t stop until 1900 that evening. We’d had an unusual winter, with little snow. Here we were in April and it had snowed for over 12 hours! I really wanted to get out for a SOTA activation and the snow was only going to enhance my adventure. I spent some time (probably too much time) thinking of suitable peaks to climb whilst at work that day. Ben Newe fitted the bill perfectly. Continue reading Guest Post: Fraser Activates Ben Newe Despite the Winter Weather

SOTA Field Report: How long will Pale Blue Li-Ion rechargeable batteries power the Elecraft KX1?

February and March 2022 were a crazy couple of months for me.

So crazy, that I wasn’t able to fit in one single POTA or SOTA activation for a nearly 4 week period. I’m not sure I’ve ever been that long without an activation since I started POTA in earnest.

Between home projects, wacky weather, timing/logistics, and even a brush with Covid, I had my hands full.

Thankfully, on Friday, March 19, 2022, the stars aligned and I was able to fit in an activation of Bakers Mountain for the Summits On The Air (SOTA) program.

It was so nice hitting the field again!

Pale Blue AA Battery Field Test

I like shaking up my activations and trying new transceiver/antenna pairings. On this particular activation, I had a special test in mind.

A few months ago–almost as an impulse purchase–I ordered a set of eight Pale Blue AA Li-Ion rechargeable batteries. I didn’t check the specifications, but I did watch this somewhat promising assessment on The Tech Prepper YouTube channel.

My hope was that these little Li-Ion cells might power my Elecraft KX1 long enough to complete a field activation.

The KX1 is a marvel of QRP engineering, in my humble opinion, and it was the first super portable transceiver I owned that could be powered by internal batteries.

When the KX1 was first introduced, Elecraft recommended using non-rechargeable Advanced Lithium AA cells from Energizer and Duracell. These batteries sported a rather flat discharge curve and could power the KX1 for quite a while. Of course, the downside is they’re single-use and expensive. Six of those cells would often set me back nearly $9 or $10. Before I started doing POTA and SOTA, I kept a set of advanced lithium cells in my KX1 for casual, impromptu QRP in the field.

Doing frequent field activations–which tend to have much more transmitting time than casual Qs–it’s just not sustainable to purchase these cells, so I tend to power the KX1 with an external battery.

I couldn’t resist the thought that I could use USB rechargeable batteries in the KX1, so I forked out $60 (mild gasp!) for a set of eight AA batteries (these are purchased in packages of 4).

The cool thing about the Pale Blue batteries is that they can be directly charged from any 5V USB power source. Each battery sports a Micro USB port and its own internal battery/charge management system.

I was well aware these batteries would not power the KX1 for hours at a time, but I was hoping they could for at least 30-45 minutes.

The only way to really find out was to do a real-life field test. A SOTA activation would be ideal! Continue reading SOTA Field Report: How long will Pale Blue Li-Ion rechargeable batteries power the Elecraft KX1?

Scott’s Icom IC-705 manpack built on a Condor MCR3 chest plate

Many thanks to Scott (KA9P) who writes:

Here’s a MOLLE-related [piece of field kit] you may not have seen yet.

My summer 2022 QRP /PM rig is built around a Condor chest plate – not really a pack although there is a plate carrier compartment that thinner things store in easily enough. And I often have a small accessory pouch in the chest plate.

The key ingredient is the IC-705 adapter plate, made from scrap 0.06 inch thick aluminum scrap.

The four tines that fit the chest plate MOLLE webbing are spaced per the MOOLE/PALS standard of every 1 1/2 inches, but the tines themselves are 3/4 inch wide rather than 1 inch to make them easier to insert in the chest plate.

 

The plate is attached to the 705 with M4 by 10 socket head screws. I first used a single quick disconnect 1/4-20 photographer’s knob, and it worked, but eventually would loosen enough that the radio would start to swivel.

The orange strap that retains the adapter plate at the top of the chest plate is riveted to the adapter plate with plastic POM rivets. The chest plate is a Condor MCR3, about 26 bucks on eBay.

The radio goes in and out of the chest plate in less than a minute, and the adapter plate can be removed in a minute or two. The radio is very stable and easy to operate.

As a bonus, the loops also hold a Buddistick mast section, then a Versatee with a Buddistick.

With the antenna in front, I can change bands and adjust the whip and coil while standing. The antenna also goes in and out of the chest plate quickly.

I’m finding it’s great fun to listen and operate on the way to and from my operating destination. Definitely the easiest /PM set I’ve had. Every control and jack, and the battery, is easily accessed with the radio attached to the plate.

It’s like the 705 was intended to be used this way!

72, keep up the great work.

Scott ka9p

Absolutely fantastic pedestrian mobile setup, Scott! I love how the custom IC-705 mounting plate makes such a stable surface for the IC-705 to be suspended as you operate. As you say, you also have very easy access to all of the station components.  Brilliant!

Thank you for sharing your design notes and photos!

POTA Field Report: Gazebo QRV & Gusty Winds with the Elecraft KX1 and K6ARK EFHW

One of the things I love about our state and national parks is that no matter how often I visit, there’s almost always something new to discover.

This is especially the case as the seasons change from winter to spring.

On March 20, 2022, I carved out enough time in my afternoon to fit in a quick activation of Tuttle Educational State Forest. My main goal, in truth, was fitting in a nice hike–the weather was beautiful, although it was rather gusty.

I needed a little “radio therapy” that day as I had been spending time in the hospital with my mom who had a nasty case of pneumonia. This was a few weeks ago and she’s feeling much better now, thankfully, but those hospital weeks in March were pretty stressful for all of us.

Field activations are such an effective way for me to get in a little exercise, a little radio time, and clear my mind; again, proper “radio therapy.”

Tuttle Educational State Forest (K-4861)

For this trip, I packed the Elecraft KX1 field kit which included my K6ARK EFHW antenna since that was the last pairing I’d used int he field (click here to read that report). I did, however, transfer the KX1 to my new Pelican 1060 waterproof case.

I actually have a solid yellow Pelican 1060 case for the KX1, but after reading about Leo’s QCX-mini field kit built in a clear-topped Peli 1060, I realized how much I missed having a clear lid on the 1060. I checked Amazon and discovered that their blue one was on sale, so I grabbed one. This was a total impulse purchase, by the way.

And for the record: I’m accused of being a radio enabler on a daily basis, but in my defence I promise the enabling works both ways! I’ve bought so many things based on reader recommendations. 🙂 Continue reading POTA Field Report: Gazebo QRV & Gusty Winds with the Elecraft KX1 and K6ARK EFHW

CW saves Leo’s POTA activation during a low battery warning!

Many thanks to Leo (DL2COM) who writes:

Thomas,

Today was crazy: when I woke up I thought it would be a good idea to attempt a first activation of DA-0171 in central Berlin after dropping off the kids at day care. So I grabbed my KX2 bag and jumped on my bike.

Shortly later I arrived at the park and pulled up my 40-10m EFHW and started calling CQ on SSB 40m.

It took me about 30 mins to realize that the KX2 was regulating the power down to 5W since both the internal and the external 4Ah battery I took with me were nearly dead.

I had one QSO with a German station and felt I wasn’t really heard anywhere. Then my KX2 started showing “low batt”.

It’s funny because attempting an activation isn’t really what one would call a very important thing, but I do develop quite an ambition if I have decided to get it done. So my only chance was using CW even though I am all but ready for that.

Having read your article about auto-spotting and watched many of your videos including POTA QSO style I didn’t think long and started calling CQ POTA on 20m.

OMG what followed was just amazing!

Fortunately I didn’t run into a classic pileup which would have been super overwhelming for me, but instead about every 2 minutes someone would reply to my call and in a very patient fashion – including one P2P QSO with an operator from Italy.

So all in all I completed 13 QSOs on a “low batt” warning of my KX2.

CW literally saved by butt and I am a very happy person. Without your work for the ham radio community this would not have been possible. So many thanks again.

On a different note: Last weekend (kit building seminar with the club) I had my first DX QSO. It was K3LU who picked up my call from my KX2 and a random wire 9:1 Unun antenna (L-Shape on a mast) with 28 and 17ft legs. I had to sit down and open a beer not able to do anything for about an hour but smile. Such a motivating event and I am happy he was such a great operator instantly QRSing with me and repeating his call. I am in touch with him and looking forward to receive his QSL card which will probably go in a frame.

I also finished the TR-35 and must say I am super impressed. It runs very quietly and the reduced concept is something I really appreciate. When will you take it into the field?

All the best & 73s de Leo (DL2COM)

Oh wow, Leo! I love this–thank you so much for taking the time to share your experience.

First of all, thank you for the kind comments–I’m honored to have even played a minor role in your CW activation. In truth, this is all chalked up to your determination and bravery! I’m guessing what you discovered is what I discovered during my first CW activation: not only is it not as bad as I had imagined, but it was actually fun and got the adrenaline pumping! 🙂 

I’m now happy to know that when I hit the Low Battery warning on my KX2, I still have some time left! In truth, the KX2 is so efficient, I’ve made six individual CW 5 watt activations on one charge of the internal battery without even hitting the low battery warning. 

Again, this story just makes my day. CW is such a fabulous, efficient, and magical mode! Good on you for diving in, OM!

I also think it’s brilliant that you worked Ulis (K3LU). You couldn’t have worked a better op for your first CW contact–he’s the real deal and a wonderful fellow. Not only that, but he has some amazing QSL cards!

And the TR-35? I couldn’t agree with you more. I did an activation with the TR-35 last Friday so a video and field report is forthcoming!

Thank you again, Leo! I hope others share their experience hitting CW for the first time (hint, hint!). 

Video: Taking the new (tr)uSDX QRP transceiver on a CW POTA activation!

As I mentioned in a post published three days ago, I’m now the proud owner of a (tr)uSDX QRP transceiver.

The (tr)uSDX has been a much-anticipated QRP transceiver for those of us who love playing radio in the field.

What’s not to love? It sports:

  • Up to 5 watts output power
  • CW, SSB, FM, and AM modes
  • A built-in microphone
  • Five bands: 80, 60, 40, 30, and 20 meters
  • A super compact and lightweight form factor
  • An open-source hardware and software design
  • Super low current consumption in receive
  • A super low price of roughly $89 US in kit form and $143 US factory assembled (via AliExpress, but there are numerous other group buys and retailers)

Frankly speaking, this sort of feature set in such an affordable package is truly a game-changer. Back when I was first licensed in 1997, I could have never imagined a day when a general coverage QRP transceiver could be purchased for under $150 US. The price is almost unbelievable.

My initial impressions

On Wednesday, March 30, 2022, I took the (tr)uSDX to the field to attempt a Parks On The Air (POTA) activation. I had only taken delivery of the (tr)uSDX about 15 hours beforehand and had only had it powered up for a total of 30 minutes the previous day. Most of that time, in fact, was checking the power output at various voltage settings into a dummy load. I did make one totally random SSB POTA contact shortly after hooking the radio up to my QTH antenna.

I knew that taking the (tr)uSDX to the field and making an activation video might not be the best idea having had so little time to play with the radio and get to know it in advance, but then again, I was simply too eager to see how it might perform.  That and I always believe there’s value in sharing first experiences with a radio. Continue reading Video: Taking the new (tr)uSDX QRP transceiver on a CW POTA activation!

The (tr)uSDX QRP transceiver: My initial impressions after a CW POTA activation

I mentioned in a previous post that I placed an order for a (tr)uSDX kit with roWaves in February. My order was placed for a third production run kit and I assumed I would receive it sometime in March 2022.

Later that month, I discovered that DL2MAN announced AliExpress would sell both kits and fully-assembled versions of the (tr)uSDX. I used the link from DL2MAN’s website and ordered a fully-assembled unit.

My thinking was that I would receive the kit first, build it, then test the performance by comparing it with the factory-assembled unit. These units are so dang affordable I felt like I could splurge for both.

roWaves order on hold

I recently discovered that my (tr)uSDX kit had been placed on hold due to issues that popped up in the first and second kit group buys via roWaves.

Evidently–and someone can correct me if I’m wrong here–the first and second production runs kits had a component issue that equated to lower output power. In addition, Josh (KI6NAZ), reports that the early group orders had no boot loaded and the MCU was DOA.

I’ll patiently wait for roWaves to sort this out. I’m not in a huge hurry at this point because, frankly, my available time to build a kit has come and gone. The next few months, I’ve a lot of plans, travels, and projects to work through.

Fully-assembled (tr)uSDX

Much to my surprise, the assembled (tr)uSDX arrived Monday and I picked it up when I was at home on Tuesday of this week.

I was only home one night, but managed to do some quick testing.

I soldered Anderson Powerpole connectors on the supplied power cable pigtails. Next, I hooked the (tr)uSDX up to my variable power supply and a dummy load.

A quick test showed that I was getting about 3 watts of output power with about 13-13.2 volts, 3.25 watts at 13.8 volts, and 2 watts of power with 9-10 volts. This is lower than the expected 5 watts of output power @ 13.8 volts. The current consumption in receive however was about 60 mA even at 9 volts. That’s slightly below the published specs.

I honestly had no time that evening to play radio, but I took a moment to hook up the (tr)uSDX to my skyloop antenna just to check the audio quality in SSB.

As luck would have it, the first station I heard on 40 meters was a POTA activator in Ohio. He was calling CQ, so I couldn’t help but reply. I pressed the PTT button on the (tr)uSDX, spoke into the internal mic,  and he came back immediately with a 5×8 report. My meter was showing a max of 2 watts output power–the heavy lifting, of course, was done by the antenna.

This gave me a very good initial impression!

(tr)uSDX POTA Activation

The following morning, after running a few errands and carting my kids to some appointments, I left the QTH for a couple nights of travel.

I just couldn’t help but pack the (tr)uSDX and attempt a park activation en route. My goal was to see if it had enough positive receiver characteristics to be a proper POTA/SOTA portable rig–the feature set is comprehensive for a $135 radio.

I stopped by South Mountains State Park and paired the (tr)uSDX to an EFHW my buddy Steve (MW0SAW) kindly built and sent me. [Steve–I’m loving this antenna! Thanks again, OM!]

I made a video of the entire activation and will soon post the field report. I’ll push this video to the front of the line, but with my internet bandwidth, it might still be a few days before I can post it. Because of this, I thought I’d go ahead and share some of my experience with the (tr)uSDX in case you’ve been thinking of purchasing one.

(tr)uSDX pros

This little radio design has a lot going for it.

The chassis is very compact–perhaps the size of two Altoids tins stacked on top of each other. The encoder does protrude–in fact, it’s nearly as deep as the radio chassis. It’s not that the encoder is particularly tall, it’s just that the (tr)uSDX is so wee.

The radio has all of the CW adjustments you’d typically find in a compact field transceiver and even sports QSK (there’s also a semi QSK setting) with no relay noise. I assume it uses PIN diode switching.

(tr)uSDX Cons

Unfortunately, I did find a few negatives. The reviewer in me automatically gives the (tr)uSDX wide berth and a lot of forgiveness: we’re talking about a $135 transceiver here. I don’t think anyone is under the impression this would be a stellar performer.

In my opinion, the biggest negative is the (tr)uSDX audio. This little rig has a very high noise floor–perhaps S5 or S6.

The internal speaker is very modest and mine is incapable of producing audio at a level that is workable in the field where there are ambient noises like wind, water, conversations, birds, etc. The audio sounds decent when working a strong station, but weak stations are extremely hard to hear. If you turn up the volume on my unit beyond level 14, the audio simply squeals. I need to tinker with the volume control more.

Since the audio was so weak, I hooked up my Sony digital audio recorder to the (tr)uSDX headphone jack and made a separate audio recording for the upcoming activation video.

The headphone audio is louder, but there’s also a lot of noise in the audio amplification chain–again placing the (tr)uSDX noise floor around S5 or S6.

I was fully expecting the (tr)uSDX receiver to overload and it does. The variable filter helps and narrowing it makes the audio sound more pleasant in CW, but it doesn’t stop adjacent signals from bleeding through. Honestly, though? I could live with this and just use the filter between my ears if the audio was simply cleaner.

I also discovered that my unit needs alignment: the frequency display is off by 1.6 kHz in CW mode on 40 meters. I’ve put this on my to-do list–after all, this is a project radio meant for hands-on tweaking. I’m good with that.

One final point and minor quibble: the OLED display is very difficult to read outdoors. It’s superb indoors, but outside any sunlight or reflection simply wipes it out. To read the display I had to cover it with my hand.

The activation was a success: I worked 11 stations in 20 minutes or less, but I’m sure there were weaker signals out there I missed because they were simply buried in the (tr)uSDX’s noise floor.

I liked the (tr)uSDX keying, and I love the form factor, but I’m not sure I’ll ever use this radio again–configured as it is now–during an activation. For casual contacts, it could still be fun.

A little (tr)uSDX grace

I mean…$135 right?!?

The (tr)uSDX is an open source project and truly pushes the boundaries of what one can achieve for $135–again, even much less for the kit version. Frankly, I’m in absolute awe that any transceiver can be made below the $150 price point; especially a multiband, multimode transceiver.

The (tr)uSDX is an experimenter’s radio and I plan to dig into this little unit and see if there’s anything I can do to lower that noise floor. My hope is that the CPU or display may simply need better grounding or isolation. My time is limited at the moment, but I will open into this radio in the next few weeks.

In fact, eventually completing the kit build will give me an opportunity to explore the components and connections in much better detail.

I do know that my unit also seems to have the power output issue that some of the roWaves kits have. I can’t achieve anything better than 3.25 or 3.5 watts output at 13.8 volts. It should be about 5 watts at 13.8 V.

I would welcome your suggestions especially if you’ve built the (tr)uSDX kit or if you’ve put your assembled (tr)uSDX on the air and found that it had much better audio characteristics.

Antenna Challenge #2: K6ARK End-Fed Half-Wave paired with the Elecraft KX1

I mentioned in a previous post that my personal Activation Challenge for 2022 was “to build a new antenna each month and deploy it at least once that month during a field activation.”

In January, I built a doublet with a military fixture/winder.

For February, I decided to purchase and build a counterpoise-less end-fed half-wave kit from from Adam (K6ARK).  This kit is available on Amazon.com for a mere $19.95 (affiliate link).

The build itself is pretty straight-forward and not terribly complicated. With that said, you do need a fine soldering iron tip and a little dexterity to manipulate these super tiny components. Adam includes instructions for building an EFHW with a counterpoise, without a counterpoise, or a random wire antenna. The coil can be configured as a a 49:1 Unun, 9:1 Unun, or 1:1 Balun.

If you choose the EFHW route you will need to solder one surface-mount capacitor on the board. If you’ve never worked with surface mount components before, take your time and use a good magnifying glass.

Blue Ridge Parkway (K-3378 NC)

On Monday, February 21, 2022, on my way back from town, I hopped on the Blue Ridge Parkway and drove to one of my favorite roadside spots on a grassy hill surrounded by trees.

Since I configured the K6ARK kit as a counterpoise-less EFHW, I wasn’t entirely sure how stable the SWR would be in the field. For this reason, I was a wee bit nervous pairing it with my MTR-3B since that little radio lacks an SWR meter and really needs a good match.

I decided, instead, to pair the K6ARK antenna with my Elecraft KX1 which has a built-in ATU that can both monitor the SWR and find an impedance match if needed. Of course, I turned off the internal ATU for the activation, but if I needed it, I knew I could engage and use it. Continue reading Antenna Challenge #2: K6ARK End-Fed Half-Wave paired with the Elecraft KX1