Antennas, News, Portable, QRP

Notes from new Elecraft AX1/AX2 owners

11 Comments

After posting my latest field reports using the Elecraft AX1 antenna, I’ve received a number of messages from new AX1 owners. All of the following have kindly allowed me to share them here with you.

AX1 Patio DXing

From Michael (K1ETA):

Thomas,

I am a subscriber and an avid follower. [L]ike you, I do a lot of portable ops with various antenna setups and radios. I was recently offered an AX1 and I was told it was basically a dummy load. Having seen your videos and proof of success I accepted it and I can’t say how much fun I have with it. Yesterday, I made 22 DX contacts throughout Europe in the ARRL World Wide CW contest from my patio in my back yard with 5 watts, the AX1 and my KX2.

I would never have tried that with the AX1 had I not seen your videos. You see it is even good enough for contests if you don’t try to compete with the big guns. Listen, search and call back the stations without pileups!

Many thank for all you do and for making me an AX1 believer.

72

Michael Kenney (K1ETA)

Pairing the AX2 and Emtech ZM-2

From Michael (N7CCD):

Hi Thomas,

I just finished your video comparing the AX1 and AX2 and thought you might appreciate a solution I came up with for making my travel more compact.

I purchased the AX2 during the February sale and found it pairs well with the ZM-2 ATU for my IC-705 (wow what a mouthful of acronyms. No wonder my wife and daughter call me a nerd…). I didn’t get the tripod adapter in the sale, but found the AX2 sits perfectly on the ZM-2 which acts as a very stable stand. There is some body capacitance when tuning, but not too much. I was even able to easily tune it on 17M. I need to try other higher bands sometime.

I set it up in our breakfast nook just for kicks and sent a few JS8 and FT8 transmissions to see where I was being heard (I’ll include a screenshot). Was able to successfully send an APRS text message, and I even made an SSB contact into a special event station in Nevada!

I found a hard sided case I can store the tuner and AX2 in, which also had enough room to put in a “speaker wire” antenna as an option. Why not?

I think this may replace the AlexLoop for air travel since it’s so compact and versatile.

Hope all is well on your side of the country!

Michael – N7CCD

P.S. +16 into Michigan!

AX1 DXing

From Kevin (KD8IE):

Hi Tom,

After video about the AX1 recently, I decided to order one and it came last week.

The weather’s been kind of chilly up here. As a matter of fact, it was 41 when I decided to go out and do an activation then at Cuyahoga Valley National Park.

Well, suffice to say I made contacts with the antenna a lot farther than I expected it would be. The bands were really long. First station I worked was in New Brunswick. The last two stations were Italy and Slovenia.

73,
KD8IE

Many thanks to all of you for sharing your experience and tips using the AX series antennas!

As a reminder, Elecraft has a February promotion on an AX1 and AX2 packages that includes free shipping. There are a few days of this promotion left at time of posting.

Accessories, Antennas, How To, Portable, POTA, QRP

Jim’s “WD-PT-PB” AX1/AX2 table/bench clamp mount

10 Comments


Many thanks to Jim (N9EET) who writes:

Thomas:

I look forward to all your videos and am enjoying how you use the Elecraft AX-1 in the field.

I have built the “WD-PT-PB” attachment for my AX-1 antenna.

That is, it is for Windy Day-Picnic Table-Park Bench use. It can be set up horizontally or vertically on the edge of a picnic table or at any angle on the back of a park bench and is a secure attachment for the AX-1 off the radio.

[I] bought the bolts straight and put them thru a random C clamp secured with a nut or wing nut and then bent one in my vise. Loosen the wing nut and angle the bolt any way I want and tighten the wing nut.

The pictures show it better than paragraphs of a description.

73,
Jim Long
Madison, WI
N9EET

That’s brilliant, Jim! I love how versatile the clamp is and that it even fits in your Maxpedition pouch! No doubt, it’ll help the AX1 (or AX2, or any similar antenna) survive the windiest of deployments.

Thank you for sharing.

Antennas, Field Reports, Morse Code, News, Portable, POTA, QRP

Postcard Field Report: Pairing the Mission RGO One with the Elecraft AX1 at Lake James for some QRP DX

12 Comments

Welcome to my first Postcard Field Report!

If you’ve been following QRPer.com and my YouTube channel for long, you’ll notice that I typically post two field reports with videos per week when my free time allows. Each report takes about four hours to produce along with a video. I’ve currently got a small backlog of videos I need to post, so in order to squeeze them into my schedule, I’m going to use a slightly more abbreviated field report format: a “postcard” format!

My Postcard Field Reports will still be information-packed, just slightly more concise and distilled than my average field report. I’ll primarily post these for sites I visit frequently.

Speaking of which….

Lake James State Park (K-2739)

Thursday, February 2, 2023, was a rainy, dreary day so the perfect time to play a little POTA, right?  I made time in my morning to visit Lake James State Park (K-2739).

When I arrived at the Catawba River Access, the parking lot was empty. Not too surprising considering it was a Thursday morning on a chilly, rainy day.

Of course, I had the picnic shelter all to myself, so why not use it to stay dry? Continue reading Postcard Field Report: Pairing the Mission RGO One with the Elecraft AX1 at Lake James for some QRP DX →

Antennas, News, POTA, QRP, SOTA, Videos

Video: What are the differences between the Elecraft AX1 and AX2? Should you buy one?

15 Comments
The Elecraft AX1 paired with the KX2.

During the months of January and February 2023, I’ve given my Elecraft AX1 a thorough workout. As I mentioned in a previous post, I thought it might be fun to take the AX1 out on a good 30 days worth of activations.

Turns out, I’ve had such brief windows of opportunity to play radio recently, the AX1 and now AX2 have been valuable tools in my field kit. They are, no doubt, the quickest-to-deploy and most portable antennas in my collection.

The Elecraft AX2 paired with the KX2.

If I only have a 20 minute window to squeeze in a quick park activation, the AX1 and AX2 make a valid POTA activation–with 10 logged contacts– a reality.

I originally purchased my Elecraft AX1 in the spring of 2020 and have used it extensively since then. In January 2023, I finally caved in and purchased the most recent addition to the AX family, the mono-band AX2.

Elecraft AX1 vs. AX2

Since I’ve been publishing numerous field reports recently using the AX1 (with more to come) and since Elecraft has included both the AX1 and AX2 in their February 2023 Specials, I’ve received questions from readers asking:

  1. “Should I buy an AX1 or AX2–?”
  2. and “If so, which one should I buy? What are the differences?”

At first, I simply pointed readers to the concise comparison guide that Elecraft publishes on their website (linked below).

I realize, though, that there are characteristics of each antenna that you might only discover after actually using them in the field.

I decided to make am unedited video–based on a few notes–not only describing the differences and similarities of the AX1 and AX2, but also if either would potentially benefit you as a field operator or traveler.

One quick note about resonance…

One point I touch on in the video is that both the AX1 and AX2 antennas are designed to be mostly resonant on 20 meters.

Small verticals like the AX1 and AX2, that use coils to electrically “lengthen” the antenna, have a higher Q than, say, a large aperture quarter or half wave antenna. In practical terms, this means that the window of resonance is narrow and more fickle than, for example, an end-fed half-wave.

A lot of factors can affect the SWR on higher-Q antennas like the AX1/AX2 including:

  • the type of terrain,
  • height off the ground,
  • length of counterpoise,
  • configuration of counterpoise,
  • and, most notably, the operator’s own body capacitance.

You may find that the AX2, for example, is natively resonant on 20 meters at one location, but isn’t at another location. This is quite normal. It’s also the reason why Elecraft states that both antennas are designed to be used with an ATU.

If you are pairing the AX1 or AX2 with a radio that doesn’t have an ATU (or you can’t use an external one), then you might consider making a simple capacity hat. Check out this field report and video where I paired the AX1 with the IC-705 and used a capacity hat to sort out the SWR.

Video

As with all of my videos, this one is unedited and commercial-free. If you’d like to skip through the video to the parts you might find most relevant, simply hover your mouse over the YouTube time line and click on the chapter indicated:

Click here to view on YouTube.

Another note here: I have no affiliation with Elecraft, but pushed this article and video to the front of the line to help those who are consider taking advantage of Elecraft’s  AX1/AX2 February 2023 Package Deals.

I hope you find the video helpful. I’ll try to answer any other questions you might have in the comments of this post.

Resources

Thank you

I hope you enjoyed this comparison video.

I’d also like to send a special thanks to those of you who have been supporting the site and channel through Patreon and the Coffee Fund. While certainly not a requirement as my content will always be free, I really appreciate the support.

Cheers & 72,

Thomas (K4SWL)

Accessories, New Products, News

Elecraft’s KX2 Internal Battery Charger with RTC, the KXIBC2, is now shipping

19 Comments

Elecraft KX2 owners that follow Elecraft’s email discussion groups have heard that the new KX2 internal battery charger, the KXIBC2, has been tested and would soon be available for purchase.

I checked the Elecraft website this morning and the KXIBC2 has been added to the KX2 product page within the past 12 hours or so.

There are two model numbers:

  • KXIBC2-F: The “F” in the model number indicates that it will be factory installed with a new KX2 order.
  • KXIBC2: This is the part you would order if you already own a KX2 and plan to install it yourself. This one is referred to as the “Kit” version since the user installs it.

The price is $139.95 US plus shipping.

I just ordered the Kit version and paid a total of $149.30 US with shipping.

According to Elecraft, the kit version is actually very simple to install, but there’s an option to have the factory install it for you via an RMA. Elecraft notes:

Anyone with a modest amount of soldering experience should be able to do the KXIBC2 installation. Based on lots of feedback from field testers, we dramatically simplified the installation procedure. For field installation, we recommend “Method 1” (see the revision B2 instruction manual or later). There’s no need to do any disassembly other than removing and replacing the right side panel. And there are only two wires to solder. If after having a look at the instructions you feel that you’d rather let Elecraft to the job, we’ll be happy to. Simply contact [email protected] to obtain an RMA.

I’ve been looking forward to this particular KX2 upgrade.

While I don’t find removing the internal battery, charging it, then replacing it very cumbersome–I’ve literally done this hundreds of times–the new internal charger will make topping off the battery that much easier.

The KXIBC2 replaces the previous KXIO2 Real-Time-Clock optional module. If you have the KXIO2 installed, you’ll need to remove it and replace it with the KXIBC2.

The KXIBC2 retains the RTC (real-time-clock) function.

For more information about the KXIBC2 module, check out the product manual and installation guide here (PDF).

News

HRCC Livestream Saturday, February 18, 2023: We’re talking packs & bags!

2 Comments

Josh (KI6NAZ) over at Ham Radio Crash Course has (in what must have been a momentary lapse in judgement) invited me back on his Saturday Night Live Stream to talk packs, bags, and radios.

Of course, this being one of my favorite topics, I’m looking forward to it. That and Josh is a great host.

The live stream starts at 5:00PM PST/8:00PM EST on Saturday, February 18, 2023.

Click here to bookmark it.

Field Reports, Morse Code, News, Portable, POTA, QRP, QRP Radios, SSB, Videos

Taking the Xiegu G106 on its maiden POTA activation!

12 Comments

Last year (May, 2022), Xiegu announced a new compact field radio that would be added to their line of transceivers: the Xiegu G106.

As I was capping off my summer in Canada (August, 2022), Radioddity started shipping the G106. Radioddity had me on their list of folks to send a loaner G106 to, but I didn’t have time to even look at the radio I was so busy upon my return, so didn’t immediately request it.

I did watch, however, K8MRD’s initial review and updated review of the G106. It was less than stellar [understatement alert!] but more than relevant to me because Mike shipped his second unit to me on behalf of Radioddity.

I connected that G106 to a dummy load, checked the transmitted signal, and it simply didn’t look very clean. It looked worse than it did when Mike checked it only a couple weeks prior.

I shared my results with Radioddity, told them I didn’t feel comfortable putting it on the air for testing in the field, and they asked to have that unit returned and checked out.

Updated G106

Fast-forward to January 2023 when I was once again contacted by Radioddity to see if I would like to field test an updated G106. I was happy to do so, in fact, because I was curious if the whole G106 experience had improved.

In the spirit of full disclosure: keep in mind that Radioddity is a Xiegu retailer/distributor–they are not the manufacturer nor are they owned by Xiegu. They are a sponsor of QRPer.com, but have no say in what I post nor any sort of editorial input. Indeed, this is always a condition of sponsorship from day one.

To Radioddity’s credit, some of my most critical reviews have been of products they’ve sent me on loan (especially the GSOC).  They take criticism on the chin and keep on moving forward. This is why they are still a sponsor and I like working with them. They understand that I call it like it is and stand by what I publish.

This G106 has been sent to me on loan for a few weeks to review. I plan to take this unit on a number of activations and pair it with a variety of antennas and accessories.

Very early impressions

I will eventually publish a full review of the G106 (likely in The Spectrum Monitor magazine first) once I’ve put in a lot more field and shack hours with the G106. In the activation video, below, I do make a lot of comments about the radio–thinking out-loud–so if you’re considering purchasing the G106, you might at least listen to a few of my initial impressions.

I will say this: for a modern SDR-based transceiver, it’s pretty bare-bones. It lacks a number of features I assumed it might have despite the incredibly affordable $320 US price point:

  • No SWR meter
  • No Power meter
  • No CW or Voice message memories
  • No RF gain control
  • No AGC control
  • No dedicated headphone audio output

But, again, it has more features than many of the bare-bones CW-only QRP transceivers out there, so for the price perhaps expectations should simply be in check–?

Zebulon B. Vance Birthplace (K-6856)

On Tuesday, January 31, 2023, I took the G106 on its maiden POTA activation to K-6856.

The G106 doesn’t have a built-in ATU (which I would never expect at this price point) so I decided to pair it with a resonant antenna. Since it was a very rainy day and the area/ground where I tend to deploy my wire antennas at Vance was squishy and soft, I opted to deploy my Chelegance MC-750 next to the picnic shelter. Continue reading Taking the Xiegu G106 on its maiden POTA activation! →

News, QRP Radios

Last batch of new Yaesu FT-818NDs: List of retailers and pricing

27 Comments

Many thanks to a number of readers who’ve pointed out that some of their favorite ham radio retailers have now received their final batch of Yaesu FT-818NDs.

I’ll post a list of retailers below (in alphabetical order) who are showing stock at time of posting (Feb 16, 2023):

Should you bite the bullet?

If you’ve been considering a new-in-box, fully warranted FT-818ND, it might be worth purchasing one of these units.

As I mentioned in previous posts, I would certainly not panic-buy an FT-818ND because there are so many tens of thousands of these in the wild I think there are deals to be found on the used market. I do suspect there may be a temporary increase in prices on the used market, but in a few months they’ll go back down.

Other retailers with inventory?

Am I missing a retailer in the list above? Please comment with a link and I’ll add them.

Antennas, Field Reports, Guest Posts, News, POTA

VE6LK: Antenna tuning on Superb Owl Sunday

5 Comments

(This article is full of educational and fun links – click on as many as you wish)

Antenna tuning on Superb Owl Sunday

by Vince (VE6LK)

While many in North America were watching a number of Superb Owls move a pigskin around a playing field, I was off to play radio, successfully, for the first time in weeks. This is part of my goal to activate 200 CW POTA contacts per month this year.

During recent visit to Vancouver attempting to operate from within my hotel room, and utilizing the Edisonian Approach, I was shown -more than once- what did not work. This will no doubt be a discussion point on an upcoming Ham Radio Workbench Podcast. I was therefore in very bad need to get back on the air while operating portable. I was close to feeling twitchy and in need of some POTAXXIA (Hyperradio Moduzolium). A plan was needed!

My goals were to trim out a new-to-me EFHW (thanks VE6VID), and make some contacts while operating outdoors. The weather was forecast for 50F, but turned out to be unexpectedly windy. Also, when the wind comes off the Canadian Rockies in Southern Alberta, it cools the area where I’d be (downwind), so a choice of operating location was key. I love going to this park for the moment that you drive west along Highway 533 and come around the corner as you see here in this short video.

Chain Lakes Provincial Park (VE-1168) is located between the Porcupine Hills and the Rockies on Highway 22 (locally known as the Cowboy Trail) in Southern Alberta, about 90 minutes south of Calgary. It’s especially gorgeous at sunrise and sunsets. A campground, lake with boat launch and a day use area all adorn this park created for water management with an earthen dam. While it is in a valley, the wind can be howling on some days. On this day it would prove to be just above a nuisance, sort of like mosquitos in the spring -you can live with the nuisance, but only for so long before you blow a proverbial gasket.

Short video – beautiful site and babbling brook

I located a lovely spot below the dam -and the majority of the wind- however it was outside of cellular range. I’d need to rely on the Reverse Beacon Network to spot me. The RBN will, in turn, post your spot to the POTA website once it hears you if you schedule your activation in advance.

RBN showing spots on 30 to 10m
Overhead site view showing my two operating positions

The place I found would only be more perfect were it warmer than 45F and without wind. A babbling brook was by the picnic table, and a nearby footbridge had built-in supports for my painter’s pole that would serve as the far end support. I’m pretty sure that they weren’t intended for me specifically, but they were the perfect size to simply slide the pole into place and hold it firmly. By luck I parked the truck the correct distance away with it’s drive-on mount and 28′ Fibreglass Flagpole from Flagpoles-To-Go via Amazon. Continue reading VE6LK: Antenna tuning on Superb Owl Sunday →

How To, News, QRP, QRP Radios

Penntek TR-45L: Adjusting the sidetone level

13 Comments

Many thanks to David (KQ4CW) who writes:

I received my Penntek TR-45L on Friday.

Just for your info: if anyone wishes to adjust the sidetone level there is a way to do that:

TR-45L Internal Sidetone Adjustment

The sidetone level adjustment can be accessed by removing the front panel assembly from the rear case.

First, remove the six screws that secure the panel to the rear case half. Separate the panel assembly and lay it face down on the table. Be careful with the interconnecting cables.

While operating the unit, adjust the sidetone level pot (circled in red) for the level of your liking. Reassemble the panel to the case rear. You may need to squeeze hard on the corners to make the panel fit. Be careful with the dress of the internal cables.

Thank you so much for sharing this, David. This is a very simple procedure and shows, also, how WA3RNC designed the boards so that the pot is accessible without having to pull apart the two main boards!

QRP radios, product announcements, reviews, news and more. Low power amateur radio fun!