Field Reports, News, Portable, POTA, QRP, QRP Radios

POTA Field Report: Pairing the Xiegu X6100 and PackTenna Random Wire

5 Comments

I’ve had a lot of fun testing the Xiegu X6100 in the field. Each time I’ve taken this little shack-in-a-box radio outdoors, I’ve paired it with a different antenna.

I’ve paired it with the Elecraft AX1, an End-Fed Half-Wave, and my 28.5′ speaker wire antenna.

On January 10, 2022, I decided to try one more antenna: the PackTenna 9:1 UNUN random wire.

The Packtenna random wire is a brilliant little antenna to pair with radios like the X6100 that have built-in, wide-range ATUs. It’s such a small antenna and can easily find matches on my favorite POTA/SOTA bands:  40 meters and up. It’s also very compact and super durable.

I use te PackTenna random wire quite a lot in the field, so I was curious just how effectively it might pair with the X6100. Continue reading POTA Field Report: Pairing the Xiegu X6100 and PackTenna Random Wire →

Field Radio Kits, Grab And Go, News, Portable, POTA, QRP, QRP Radios, SOTA

My new MTR-3B Ultra-Compact Field Kit built in a Tom Bihn HLT2

12 Comments

I’m a bit obsessed with field radio kits (understatement alert).

If you don’t believe me, check out this episode of the Ham Radio Workbench podcast where they graciously allowed me to geek out about radio packs for a good two hours.

I should also note that I write, in detail, about my packing philosophy in this Anatomy of a Field Radio kit series.

There’s no cure for my pack obsession. I’m constantly in a state of assembling and testing the most efficient kits I can conjure up.

Since I rotate a fair amount of radios in my activations, the majority of my kits are modular; meaning, components like antennas, ATU’s, batteries, log/pen, and cables are packed in their own small pouches/pack. Before embarking on an activation, I simply assemble the components in a backpack along with the radio/s I might use that day. Over the years, I’ve developed a certain workflow with this process that ensures I don’t forget components or pack the wrong ones.

But by far, my favorite type of kit are those that are fully self-contained–proper grab-and-go kits that have everything I need inside to, for example, activate a summit.

Self-Contained Kits

Fully self-contained kits are reserved for the radios I use in the field most because, frankly, they’re stingy resource hogs: they  don’t share components with my other radios or kits. Continue reading My new MTR-3B Ultra-Compact Field Kit built in a Tom Bihn HLT2 →

Articles, Hacks and Hints, How To, QRP Radios

Rich builds a simple GX12 key/paddle adapter for the Discovery TX-500

7 Comments

Many thanks to Rich (KQ9L) who shares the following tutorial describing how to build a compact key/paddle GX12 connector for the lab599 Discovery TX-500:

This adapter is simple, compact, and eliminated the need for yet another wire extension.

How to build a Discovery TX-500 key adapter

I love my Lab599 Discovery TX-500 however I was frustrated with all the extra “wires” hanging from the connectors on the rig.

I took inspiration from Vlad Solovey (RA9QAT) who posted his design for a small and compact 3.5mm jack that allows you to connect your paddles directly into a GX12 connector. Continue reading Rich builds a simple GX12 key/paddle adapter for the Discovery TX-500 →

Antennas, Field Reports, News, Portable, POTA, QRP

Pairing the Xiegu X6100 with the Elecraft AX1 antenna…will it work?

16 Comments

If you’ve been reading QRPer for long, you’ll note that I’ve become quite a fan of the uber-compact Elecraft AX1 antenna.

Not only has the AX1 never let me down, but it can even outperform my other antennas in terms of snagging contacts during an activation. Yes, it can even work some DX as well.

Normally, I pair the AX1 antenna with my Elecraft KX2 (above) or KX3 (below).

I’ve even paired the AX1 directly to my Icom IC-705 using a homebrew simple capacity hat (thanks again for that idea LY2H!)

The AX1 needs a little help from an antenna tuner (ATU) to get a match across the 40, 20, and 17 meter bands. Of course, I could always mount the AX1 on a tripod and attach an in-line ATU, but I love the simplicity and speed of setup when paired directly to a transceiver that sports an internal ATU.  To be clear, the Icom IC-705 has no internal ATU, but I was able to get away with using a capacity hat to match impedance on 20 meters.

The new Xiegu X6100 (above) has an internal ATU–a good one at that! As soon as I took delivery of this loaner unit from Radioddity, I plotted hooking it up to my AX1 to see how it might shake out in the field!

The X6100 lacks only one thing that the KX2, KX3, and IC-705 have: a good, accessible grounding point on the chassis.  The AX1 needs a counterpoise to operate efficiently. Continue reading Pairing the Xiegu X6100 with the Elecraft AX1 antenna…will it work? →

Announcements, News, QRP Radios

New Xiegu X6100 V 1.1.2 firmware addresses a number of known issues

26 Comments

Yesterday, I received the following notification from Radioddity regarding a new firmware version for the X6100.

I mentioned that I’ve purchased an X6100 and it’s en route to me now. It was dispatched prior to this new firmware being made public.

It addresses a number of outstanding issues:

  • Improved battery management
  • Functional CW message memory keying (thanks for confirming, Scott!)
  • Improved noise reduction functionality in CW mode
  • CW decoding algorithm improvements
  • Added hand mic button functionality
  • Bluetooth connectivity improvements
  • Many more…

I’m looking forward to this improved functionality–especially CW message keying and battery management. Continue reading New Xiegu X6100 V 1.1.2 firmware addresses a number of known issues →

Announcements, Kits, Morse Code, New Products, News, QRP

The new WA3RNC TR-35 4-Band 5-Watt CW Transceiver Kit

9 Comments

Many thanks to Jim (N9EET) who notes that WA3RNC will soon be shipping his latest QRP transceiver kit: the TR-35.

According to the WA3RNC website, factory wired/assembled kits are available now for $379 US. The regular kits (with pre-wound toroids!) will be available for purchase January 24, 2022 for $279 US. If you’d like the pre-assembled version, simply click the checkbox that adds $100 for assembly in the WA3RNC store.

Here are a few TR-35 specs from the WA3RNC website:

    • Size 5 ½ X 3 ¼ X 1 ½ less protrusions, weight 10.6 Oz
    • 5 watts output on all bands at 12vdc input
    • Full coverage of 40, 30, 20, and 17 meters with extended RCVR  tuning above and below
    • RCVR modes for CW narrow and CW wideband, and for SSB reception
    • Optimized for operation from 3 series-connected 18650 Lithium cells
    • RIT tunes + and – 5KHz
    • Blue OLED display reads frequency to 10 Hz and RIT offset
    • Built in Iambic keyer is adjustable 5 to 45 WPM with front panel control
    • Separate jacks for straight key and paddles; Always ready for SKCC contacts
    • Operates on 9.5 to 14 volts, < 100 ma receive, about 1 Amp Xmitt at 10 volts
    • Selectable tuning resolution steps of 10, 100, and 1000Hz
    • Low battery indicator with internal adjustment 9.5 to 11.5 volts 
    • Front panel adjustable RF gain control
    • Front panel TX power control; Adjustable from 0 to full output
    • Rugged TO-220 FET RF amp has delivered 5 Watts key down for 5 minutes
    • Signal quality blue LED, RIT warning orange LED, Low battery red LED
    • Excellent receiver sensitivity with MDS of -125dBm
    • Very effective receive AGC prevents ear damage with strong signals
    • Transmitter harmonics and spurs -52dB, meets FCC specs
    • CW sidetone is the actual transmitter signal as heard by receiver
    • Match the received signal tone to the sidetone for perfect zero beating
    • Sharp IF filter; Better than 350 Hz at the -6dB point, plus 700 Hz audio filter
    • Over 250 machine placed SMT parts, and about 55 user installed parts
    • All critical circuits are factory pre-aligned and calibrated
    • No endless “back menus”; There is a control or switch for every function
    • Factory wired and tested option available
    • All torroids are factory wound and prepared

Resources

I love the simplicity of WA3RNC’s designs! I’m sure this will be a popular little kit!

Guest Posts, News, QRP Radios, Reviews

Guest Post: Erik’s Review of the Venus SW-3B

9 Comments

Many thanks to Erik (KE8OKM) who kindly shares the following guest post:

Venus SW-3B Review from a newbie SOTA/POTA activator’s viewpoint

by Erik (KE8OKM)

My journey into amateur radio is relatively short (approaching 2 years now) in this short time I have become enamored with “in the field” QRP operating. Particularly SOTA/POTA.

SW-3B in action Bearcave Lookout PA SOTA!

When I started studying for my tech license I kept coming across CW–what the heck is that? After I learned it’s a mode using Morse Code (a highly effective one at that) I thought, “not interested” and “they still do that?”

Much to my chagrin, I find myself loving CW and obsessed with all things Morse! The CW mode is both a skill and an art. I am still drawing with crayons but hope to paint someday…at least like Bob Ross…

The Venus SW-3B is a small 3 band transceiver operating on the highly effective 20/30/40m bands: the SOTA/POTA activator’s bread and butter bands. To date I have logged over 450 QSOs with this little “black box.” I often come across some disparaging remarks since the transceiver is built in China.

The SW-3B’s design and manufacturing is overseen by Dale (BA4TB). Now having 3 of these, I can say the quality is fine across the line. Product support is reported very good in the rare event it’s needed. Continue reading Guest Post: Erik’s Review of the Venus SW-3B →

Comparisons, News, QRP

The Xiegu X6100 or the Icom IC-705? Making a purchase decision…

27 Comments

Well before the new Xiegu X6100 transceiver was actually in production, I was already getting questions from readers and YouTube channel subscribers if they should plan to purchase the X6100 or the Icom IC-705.

The X6100 has been in the hands of early adopters now for about two months, so we have a good idea what the radio is capable of and how well it performs–at least, with the current firmware revision (January 18, 2022).

I’d planned to make a comparison video in a couple of weeks when the X6100 I purchased arrives, but as I was packing my loaner X6100 to ship to the next review last week, I got yet another email and made the decision to unpack the rig again and film a video comparison.

Not comparable?

Without fail, each time I do a radio comparison I get at least one email (often several)  stating in no uncertain terms: “Thomas, you can’t compare those two radios!” Continue reading The Xiegu X6100 or the Icom IC-705? Making a purchase decision… →

Hacks and Hints, Homebrew, How To, Kits, News

Xiegu X6100: Two effective ways of mitigating broadcast band interference and overloading

18 Comments

As I’ve previously mentioned, the Xiegu X6100–at least at time of posting (January 17, 2022)–has overloading issues. If you listened to the activation video I posted yesterday, you can hear a local AM broadcaster punching through the 40 meter band, especially noticeable before/after operating SSB.

Several subscribers asked if I tried using the attenuator and RF gain to mitigate the level of overloading.  Attenuators and RF gain can be an effective means of mitigating noise levels, but they essentially affect everything on the band–all signals somewhat equally.

A better approach is to use a BCI Filter.

BCI Filters

BCI filters reduce or notch out AM broadcast band signals so that they don’t overload your receiver.

BCI Filters are placed between the radio and the antenna. They can have a dramatically positive effect if you live near a broadcast station and/or if you have a radio that’s prone to overloading.

I see them as a more “surgical” approach to solving broadcast band interference.

BCI filters are simple, inexpensive, and effective. Here are two options shared by QRPer readers: Continue reading Xiegu X6100: Two effective ways of mitigating broadcast band interference and overloading →

Field Reports, News, POTA, QRP, Videos

Xiegu X6100: New compact throwline, POTA pileups & overloading in Pisgah National Forest

23 Comments

On Thursday, January 6, 2022, I woke up with one goal in mind: take the Xiegu X6100 out on a proper hike-in activation!

While I’d had this radio on loan from Radioddity since December 23rd, I hadn’t had an opportunity to truly hike it into an activation site. Between the weather and my tight schedule, I haven’t had an opportunity to plot out a proper Summits On The Air (SOTA) Activation. SOTA activations that involve hiking usually take a much bigger bite out of my day and, lately, I’ve been to busy to plot one.

I do live near a vast trail network, however, and it so happens that much of the trails run through overlapping public lands: Pisgah National Forest and Pisgah State Game Land.

So I packed my Spec-Ops EDC tactical pack, grabbed Hazel’s harness, and headed out the door.

“Let’s go, Daddy!”

Hazel knows me too well.

When she sees my pack and my hiking boots, she  waits in front of the door so there’s no possibility she’ll be left behind. Continue reading Xiegu X6100: New compact throwline, POTA pileups & overloading in Pisgah National Forest →

Connecting an international community through low-power field radio adventures.