Category Archives: Field Reports

“Three Watts and a Wire: Seizing a Last-Minute POTA Opportunity with the Elecraft KX1!

I woke up a little too early on the morning of Saturday, February 3, 2024.

The previous evening, we recorded a Ham Radio Workbench podcast episode with my dear friend Ara (N6ARA) as a guest. It was a load of fun, and we ran over time (no surprise there). Since we started recording at 18:00 Pacific Time, it means that it was 21:00 here in the Eastern time zone. By the time the episode ended, it was well after midnight my time.

For some reason, my body clock only allowed me to sleep for five hours, but I planned to sneak in a nap at some point during the day. Our plans were modest that Saturday (only to visit my father-in-law in the hospital), and I had no intention to fit in a POTA activation.

Around noon, my daughters asked if I’d drive them to watch one of their friends in a Shakespeare performance at 2:00 PM. We quickly sorted out plans, and I grabbed my GoRuck GR1 pack, which (due to a crazy January) had hardly been touched since my activation with Hazel nearly a month prior.

Pisgah National Forest (K-4510) and Game Land (K-6937)

As you’ll hear me mention in a number of my field reports, the venue where my daughters rehearse Shakespeare and perform is a short drive to Pisgah National Forest/Game Lands. In the past couple of months, I’ve enjoyed numerous activations in Pisgah.

The weather was perfect for playing radio outdoors. It was chilly, yes, but not so cold that I needed to wear gloves.

I was looking forward to putting the Elecraft KX1 on the air again. As I state near the end of my video below, it’s one of my all-time favorite QRP rigs.

My trusty GoRuck GR1

I decided to pair the KX1 with my KM4CFT end-fed half-wave that I built for 30 meters, with a linked 40-meter extension.

On this particular afternoon, I wanted to focus on 30 meters, so as I deployed the antenna, I unhooked the 40M link.

Gear:

Note: All Amazon, CW Morse, ABR, Chelegance, eBay, and Radioddity links are affiliate links that support QRPer.com at no cost to you.

On The Air

I started calling CQ POTA, and it didn’t take long for the RBN to spot me, and Evan (K2EJT) was the first to call (thanks, OM!). Continue reading “Three Watts and a Wire: Seizing a Last-Minute POTA Opportunity with the Elecraft KX1!

SOTA and POTA in Japan: Ara combines travel and radio with a little help from friends

Abroad in Japan: SOTA and POTA

by Ara (N6ARA)

Getting the License

Several months ago, my wife and I were planning our first trip to Japan, and I couldn’t help but look at all the nearby SOTA summits and POTA parks and entertain the idea of activating one of them. While stunned by the sheer number of high point summits and local parks (many of which are easily accessible via Japan’s incredible public transport system), I realized one question I hadn’t asked myself yet: Can I even operate in Japan?

I recalled the concept of a reciprocal licenses from the ham test, but never really looked into it. A quick Google search yielded the JARL (the ARRL equivalent in Japan) foreign amateur radio license website, which details the process for submitting your documents to obtain the license.

However, I quickly learned that the application must be submitted at least 60 days prior to the date of operation. Problem was… I was 58 days out.

Around this time, I let my friends, Waka-san (JG0AWE), Kazuhiro (7N1FRE), and Ted (JL1SDA), know that I would be visiting Japan. They leaped into action and helped me figure out if there would be a way to obtain my reciprocal license in time, and advised me on which summits and parks would be doable with my constraints.

Thankfully, Waka-san was very generous and offered to make an appointment with Japanese government to apply for the reciprocal license on my behalf. I was absolutely stunned by this. I struggle to make appointments at the DMV office for myself, let alone for someone else!

Two weeks later, I was surprised to learn that my license had arrived. I was now JJ0XMS in Japan. This news fittingly arrived around Christmas, making it easy to remember the “XMS” part of my call. The reciprocal license I received was classified as “1AM”, meaning 1st Amateur license for mobile. This meant I could operate on all bands at power levels below 50W, which is perfect since I tend to operate QRP most of the time anyway.

It helps to have friends around the world, but please learn from my mistake, submit your JARL-96-04 application at least 60 days (plus margin) prior to your trip and obtain your license the right way. If you have any questions about the form or the process, contact Mr. Ken Yamamoto (JA1CJP) via email at [email protected] 

Band Plan

With my license sorted, the next step was to familiarize myself with the Japanese Band Plan. After careful review, I learned it is entirely possible to accidentally transmit out of band or mode if you are not careful. For example, in the US the 2m band ends at 148 MHz, but in Japan the band ends at 146 MHz. So in theory, an operator with a US radio could accidentally transmit on a forbidden frequency.

It’s also important to note that the calling frequencies are different for all bands and that some bands have dedicated emergency communications frequencies. Thankfully, the translated Japanese Band Plan covers these extensively.

Planning the Activations

I started planning my activations by setting the goal of activating at least one SOTA summit and POTA park. I figured I’d gain the experience of doing both to see how they differ from what I’m used to in the US (and writing this blog post).

For this trip, we mainly stayed with our friend in Tokyo, so I was limited to the summits and parks near the city. To start, I figured I’d take a look at the POTA map since Tokyo is a flat city (read as, no SOTA summits to be found within the city itself), so worst case, I’d only do a POTA activation.

Much to my delight, I learned that Tokyo has 146 POTA parks within the city alone… and best of all… they are accessible via Tokyo’s public transportation system! Overwhelmed with all the options, I figured the best thing to do next is to try and see which nearby parks had the most space and activation count. I figured that would improve my odds of activating without any issues.

To be honest, my main concern was putting up an antenna in a park which I’m not allowed to in, or folks approaching me to ask what I’m doing, only to run into a language barrier issue. After looking through several options, I landed on Yoyogi Park JA-1255. The park was near where I was staying, fairly large, and had almost 100 activations. 

Next was planning the SOTA activation. Since there are no SOTA summits in the city proper, it meant I would have to travel a little to get to one.

Coming from Los Angeles, one of the most car-centric cities in the world, I did not expect to find that most Tokyo residents (including my friend) don’t own a car. Renting one is an option, but I figured it’s not worth the effort. Especially since Japan drives on the left hand side of the road – which I’m not used to. That meant driving to a trailhead was out of the question for this trip. Thankfully, that wasn’t as much of a problem as I initially thought.

Looking through the SOTA map, I found several trailheads to the east of the city that are easily accessible via train/bus and short walk. Again, I looked at the activation count to get a sense of what is attainable and found Mt. Arashiyama JA/KN-032. The summit had 84 activations with a relatively easy 762ft gain across 2.25mi and the trailhead is a 15 minute walk away from the train station. The only downside was that the train ride itself was about an hour and a half away from Tokyo. But as those who do SOTA know, the commute to the trailhead is part of the journey. (I think there’s something wrong with us.)

Packing

With a game plan settled, it was time to configure the kit. One important thing to note here is that when I submitted my paperwork to apply for the license, I forgot to include the radio make/model I planned to use (required for the application process). Thankfully, Waka-san registered the ICOM IC-705, an HF/UHF/VHF all mode transceiver (which I so happen to have). This afforded me the flexibility to work a wide range of bands and maximized my odds of having a successful activation.

With the radio figured out, I thought to pair it with a portable antenna that strikes a good balance between volume/mass and performance. My hope was to cover 10/15/20m for DX and 40m for working locals, so naturally I gravitated towards my trusted K6ARK End Fed Half Wave EFHW with an added load coil, making it resonant on 10/15/20/40m. I like to use this antenna in an inverted-V configuration using a 7.2m fishing pole. Since I had one shot at each activation, I figured it would be wise to pack a back up antenna just in case something broke mid-transport, so I also decided to pack my Elecraft AX1 vertical whip antenna and T1 tuner.

For CW paddles, I couldn’t resist packing my recently acquired Ashi Paddle 45 from Mr. Haraguchi 7L4WVU in Japan. Only seemed fitting! Finally, I thought to print out copies of my US and Japanese ham radio license, and a translated note describing ham radio, SOTA, and POTA just in case someone asked what I was doing.

Packing List:

[Note: All Amazon links are affiliate and support QRPer.com at no cost to you.]

Welcome to Japan

As soon as we landed in Japan and settle in at our friend’s apartment, we couldn’t help but go out for a nice bowl of warm ramen at Ichiran. It was a cold night, I was jet lagged, and this was exactly the “reset button” my body needed to adjust to the new timezone. I slept like a log that night. Highly recommend. 

Since this was my first time in the country, I tried my best to absorb as much of the food and culture as possible. From the Yakitori, to the Tonkatsu, to all the various Japanese curries, and Onigiri, I was glad to be walking around the city to burn off all the calories I was consuming. Everything we ate tasted incredible!

One of the first orders of business was to visit Akihabara, the electronic town I had heard so much about. Walking through shops, I found every possible component imaginable. Want a transformer? There’s a small shop that has every variant you can think of. LEDs? There’s a shop with a selection that will make you see floating dots when you close your eyes. It was like living in a Digi-Key or Mouser warehouse.

Walking through streets and multi-story markets, I was constantly running into small radio shops. Some selling commercial radios, many selling various ham radios and ham radio accessories. One golden nugget I found was a shop that sells home-brew radios, one of which was a 47.1GHz Transverter! Where else are you going to find something like that for sale in a shop?!

One last stop in Akihabara was Rocket Ham Radio, one of the largest ham radio shops in Japan (think HRO in the US). I couldn’t help myself from buying a 2m/70cm whip antenna for my IC-705 for portable VHF and UHF operations while in town. Would feel wrong leaving without buying *something*!

POTA Activation and Logging

POTA activation day was finally here, and much to my delight, Mr. Haraguchi (7L4WVU) reached out to say he was available to meet me at Yoyogi Park for a joint activation. Continue reading SOTA and POTA in Japan: Ara combines travel and radio with a little help from friends

Roadside POTA: Pedestrian Mobile with the Elecraft KH1 at Lewis Ocean Bay Heritage Preserve WMA

My family decided to take a short pre-Christmas break on the coast of South Carolina in mid-December.

It had been a hectic month, so we looked at our healthy hotel points balance and decided to burn up a few of those on an impromptu four-night getaway.

We decided to stay at the same Myrtle Beach hotel where I stayed only a couple of months prior to attend a family funeral in Georgetown, SC. You might recall my activations at Lee State Park, Myrtle Beach State Park, and Huntington Beach State Park during that particular trip.

In truth, we’re not big fans of Myrtle Beach—we prefer more secluded, less commercial spots along the coastal Carolinas. In the summer, Myrtle Beach is jam-packed with visitors—the traffic is a little insane—but in the winter, Myrtle Beach is relatively quiet. Getting around is a breeze, and accommodation is easy to find.

This trip was all about family time, so I didn’t pre-plan a single activation, and I didn’t pack several radios. In fact, the only radio I brought was my Elecraft KH1, which lives in my everyday carry backpack.

The KH1 is a constant companion these days. It was really fun to take it on one of the balconies of our room and hunt parks and summits. Despite a little QRM, I was able to make a number of contacts just using the KH1 whip and dangling the counterpoise.

I remember working my friend Alan (W2AEW) while he was activating a park in New Jersey. I sent him the photo above. What fun!

Lewis Ocean Bay Heritage Preserve Wildlife Management Area (K-3903)

On Wednesday, December 20, 2023, we decided to spend part of the morning and afternoon in Conway, South Carolina, which is about a 30-minute drive from Myrtle Beach.

My wife asked, “Surely, there’s a park you can activate along the way?” (She and my daughters fully support my POTA addiction.)

After a quick glance at the POTA Map, I determined that indeed there was!

Lewis Ocean Bay Heritage Preserve WMA was essentially on the way to Conway, and I could tell based on a quick Google Map search that one of the access points (a huge gravel parking lot) was conveniently located next to the highway. Score!

I grabbed my backpack and camera (of course I brought along the camera just in case!). We drove 25 minutes to the access point which was easy to find.

As luck would have it, as I parked, I noticed that a motor grader was resurfacing part of the parking lot and the main WMA access road. This wouldn’t affect my activation, of course, but it was incredibly loud—especially the constant back-up alert.

So that my KH1 audio would be audible over the grader noise and the highway noise, I connected it to my Zoom H1N recorder.

Setup was quick despite setting up the audio feed and arranging the camera position under the shade the open hatch of my Subaru provided.

Gear

Note: All Amazon, CW Morse, ABR, Chelegance, eBay, and Radioddity links are affiliate links that support QRPer.com at no cost to you.

On The Air

I started calling CQ POTA on the 20 meter band and it didn’t take long before hunters started calling back. Continue reading Roadside POTA: Pedestrian Mobile with the Elecraft KH1 at Lewis Ocean Bay Heritage Preserve WMA

The Georgia Wildlife Management Areas Continue to Deliver

After my last activation at Oliver Bridge Wildlife Management Area (K-3764), I considered heading to South Carolina for park #16 toward my 2024 goal of 60 new-to-me parks. However, after looking at the weather forecast, I reconsidered. I’d need to activate earlier in the day due to my schedule and, given the chilly weather, I’d prefer to sit in the car for the activation. That would not be a good option for the park I considered.

So, I began looking at more wildlife management (WMA) areas in Georgia not far from home. I chose Hiltonia WMA (K-8794) which is an hour’s drive for me. This WMA is 500 acres mostly of hardwood and long-leaf pines and is owned by the State of Georgia. The property offers hunting of deer, turkey, dove, and small game.

I did not know before my visit that longleaf pines existed on the property but figured it out when I discovered their needles while walking with Daisy after the activation. You know longleaf pine needles when you see them because they are much longer than other pine needles. In fact, they have the longest needles of the eastern pine species and can grow up to 18”. The needles I found were 14” in length!

Longleaf pine forests are special because they are rich in bio-diversity and provide habitat for the threatened gopher tortoise, a keystone species because it provides burrows in which other species, like the threatened Indigo snake, live or shelter. The endangered red-cockaded woodpecker is another species that benefits from longleaf pine forests because it lives in the cavities of mature longleaf pine trees. The species dwindled when many of the old-growth longleaf pine forests were felled and/or replaced with commercial forests of loblolly or slash pine in the southeastern US.

Gopher Tortoise. Source: https://www.aces.edu/blog/topics/forestry-wildlife/celebrating-the-gopher-tortoise/
Indigo Snake. Source: https://www.oriannesociety.org/priority-species/eastern-indigo-snake/?v=400b9db48e62
Red-cockaded woodpecker. Source: https://ebird.org/species/recwoo

You access the Hiltonia WMA via a dirt road in the middle of nowhere. The property has an information kiosk right near the entrance with a map giving you the lay of the land. I usually look at whatever maps are available online from the state of Georgia or Google beforehand. For Google maps, I usually use the topographic layer as this is the default and shows me roads to access the property. But before this trip, I played with the layers setting and discovered the imagery layer will give me a better idea of what is forested and not. Hence I could easily locate an open area to set up my antenna.

The dirt road to the park
https://gadnrwrd.maps.arcgis.com/
Google Maps – imagery view

Just past the information kiosk is a dove field and it was there my Subaru Crosstrek Kai and I set up shop. What a gorgeous day! Crisp air under clear, blue skies. Daisy explored and sniffed to her heart’s content while I installed the Tufteln EFRW antenna in the perfect pine with one toss!

The perfect pine tree!

It was not long before Daisy and I were installed in Kai and ready to get the party started. And what a party it turned out to be! Not long after I called CQ on 20 meters, Joseph KB1WCK responded. After we finished our QSO, I was buried under a massive pile-up. However, pile-ups do not intimidate this POTA Babe! I did the best I could to pick up bits and pieces and work through it. Did I make mistakes? Sure I did, but there are no CW police and this is how we learn, through challenges. Continue reading The Georgia Wildlife Management Areas Continue to Deliver

Pairing the KX2 & AX1 for my first POTA activation in weeks!

On Thursday, February 1, 2024, I managed my first POTA activation in weeks.

As I mentioned here on QRPer, January was a crazy month. Not only did I lack the time to activate parks, but I also wasn’t in the right frame of mind to make activation videos.

However, on February 1, things were looking up, and a nice little POTA activation was just what the doctor ordered!

I grabbed my KX2/AX1 pack as I headed out the door.

On the way into Asheville, I stopped by the Folk Art Center on the Blue Ridge Parkway (K-3378)–my go-to site for convenient activations. I had a one-hour window of time to fit in an activation.

BRP & MST Two-Fer

You might recall that in my last field report (from January 5, 2024), Hazel and I hiked the Mountains-to-Sea Trail (K-8313) and found a trailside spot that was also within the Blue Ridge Parkway (K-3378) property boundary. The activation counted as a two-fer!

You don’t have to hike the Mountains-to-Sea Trail (MST), however, in order to activate it and the parkway at the same time.

In the activation video, below, I show where one of the picnic tables at the Folk Art Center is close enough to where the MST passes that it counts. Makes for an easy drive-up, two-fer activation.

New Tufteln Cover!

A few weeks ago, my friend Joshua (N5FY) sent me a new protective cover for my Elecraft KX2. He’s now made these covers a part of his product line at Tufteln.com.

Like my Tufteln KX1 cover, the KX2 cover locks onto the front of the radio with rare earth magnets. It only requires that you replace the stock screws around the KX2 display with the ones Joshua provides. His replacement screws have a slightly higher profile, which allows the cover to attach magnetically.

What I love about Joshua’s covers is that they do a brilliant job of protecting all of the controls of the KX2 without taking up as much space as, say, the stock clear cover that came with my side panels.

Also, it fits the KX2 perfectly whether you have side panels or not!

Setting up

Of course, the glory of the KX2/AX1 combo is that it takes almost no time to set up in the field.

Within a minute or two, my gear was deployed, and I was on the air seeking a clear frequency.

I opted to use my Begali Traveler (over my KXPD2) key since it was also packed in my GoRuck GR1.

Gear:

Note: All Amazon, CW Morse, ABR, Chelegance, eBay, and Radioddity links are affiliate links that support QRPer.com at no cost to you.

On The Air

On this occasion, I decided to work the lower bands of the Elecraft AX1 antenna.

I started calling CQ POTA on 40 meters and, fortunately, the band was alive. Continue reading Pairing the KX2 & AX1 for my first POTA activation in weeks!

Exploring the Mountains-to-Sea Trail: QRP POTA with Hazel and a New KX1 Kneeboard!

On Friday, January 5, 2024, I looked at Hazel and could tell that, despite the chilly temps, she wanted to go on a late afternoon hike. I did, too, for that matter and why not combine the hike with a POTA activation?

In addition, we were expecting a winter storm to move in that night, so hitting the trail in advance of the snow and ice seemed to make sense.

Before I could get my boots on, Hazel was waiting by the car door to jump in.

Mountains-to-Sea State Trail (K-8313)

One of the closest long trails near my QTH is the Mountains-to-Sea Trail (MST).

At 1175 miles long, the MST stretches from the Outer Banks of North Carolina to the Great Smoky Mountains (see map above).

I can actually hike to the MST from my QTH, but it takes a good hour and half to do so. It’s much easier to drive to one of the numerous nearby trailheads, and that’s exactly what Hazel and I did. I drove to one of my favorite Blue Ridge Parkway POTA spots where a short manway connects to the MST.

Hazel was so excited to hit the trail. (I was, too.)

At the end of the day (because, it was nearing the end of the day) we couldn’t hike for long if I planned to also complete a POTA activation. Sunset was at 5:29 PM local and I didn’t want to pack up and hike back in the dark.

That said, if I needed to hike back in the dark, I could have because I never go on a POTA or SOTA activation without a fully-charged headlamp. FYI: I was packing a NiteCore NU25 (affiliate link).

I started my action camera and captured the last bit of hike before Hazel and I found a great spot to set up. There were enough trees around to deploy a 40 meter EFHW and a relatively flat spot to set up my Helinox chair and KX1 station.

Since much of this section of the MST is on the Blue Ridge Parkway grounds, I checked quickly to make sure my operating site would qualify as a two-fer with K-3378.

I opened the Parceled App on my iPhone to confirm that my site was indeed on Blue Ridge Parkway property..

A KX1 Kneeboard!

If I’m being perfectly honest, I had an ulterior motive with this trailside activation: I was eager to finally put my new KX1 kneeboard into use! Continue reading Exploring the Mountains-to-Sea Trail: QRP POTA with Hazel and a New KX1 Kneeboard!

Matt’s Weekend POTA Roundup!

Many thanks to Matt (W6CSN) who shares the following post from his blog at W6CSN.Blog:


Weekend POTA Roundup

by Matt (W6CSN)

It’s been a stormy past several days here in Northern California, but if anything, the weather only amplifies my motivation to go outside and get on the air.

Rather than do a separate writeup for each, this post is a roundup of my last four POTA activations, from Friday, February 2nd through Sunday, the 4th.

A faint rainbow splashes down in front of Angel Island

Thursday and Friday had been wet, with one storm in a series moving across the Bay Area. However, by Friday evening the cold front had passed and there was a break in the rain. This was a perfect opportunity to try an after work activation at the Presidio of SF (K-7889).

I hadn’t used the QCX-Mini in a while, and this activation reminded me why. I believe what is happening is that being so close to the antenna, RF interference causes clicking while keying, nearly to the point of distraction. I need to experiment with RF chokes on the key and audio lines to see if that improves the situation.

Fed up with the RFI on the QCX-Mini, I switched over to the MTR-4B which doesn’t seem to suffer the same issue. I wrapped up the activation after netting 21 QSOs in the cold west wind.

All QSO maps in this post are from http://tools.adventureradio.de/analyzer/

The next bout of rain wasn’t due to arrive until later Saturday afternoon. This was a change in the forecast that subsequently altered my plan to stay in Saturday soldering on my QMX Hi-Bander project.

Initially I went to Fort Point (K-0819) in the hopes of changing it up from my usual activation park but there were just too many people there. So seeking relief from crowds, I crossed the Golden Gate Bridge and went up on the slopes of Mt. Tamalpais.

I parked at Trojan Point at an elevation of approximately 1800 feet. See this post for more views from this location. The temperature was in the mid-40s, which is cold for us coastal Californians. Besides, the winds were picking up ahead of the next storm so I operated from the comfort of my vehicle using the Gabil 7350T base loaded vertical antenna on 15m and 20m.

This activation used the FT-818 and yielded 23 contacts, including JH1MXV from northwest of Tokyo, Japan coming in fairly strong on 21 MHz.

Driving back to San Francisco takes me right through the Presidio of SF (K-7889) and noticing that it was after 00:00 UTC, I made the last second decision to divert to East Beach to see if I could work in another activation before the anticipated rain.

At my usual spot for activating this park, it took only moments to raise the MFJ-1979 20m quarter wave and do a quick deployment of the MTR-4B on the trunk of the car. The wind was picking up, but not nearly as strong as it was up on the mountain.

After seven QSOs, the skies began spitting raindrops, this was going to be close! I closed the cover of the Maxpedition pouch to protect the radio and battery while the Bencher paddles could tolerate a little bit of moisture.

I was happy to have a Rite-In-The-Rain notepad for logging [Amazon affiliate link], because now I was certainly writing in the rain! Three more contacts and the activation was concluded with a hunt of Jim, WB0RLJ, in K-4011. Continue reading Matt’s Weekend POTA Roundup!

For Conrad, DC Travel = DC POTA!

Washington, DC Field Report

By: Conrad Trautmann, N2YCH

January 30, 2024

Periodically, I travel to Washington, DC for my job. On my latest trip, I carved out some time to activate some parks. The hotel I was staying at is just a few minutes away from the National Mall, which provides many activation options on the POTA website. After scoping it out on Google Earth and researching trails using the National Parks mobile app and web sites, I settled on the Jefferson Memorial, K-0792 as my first stop which is a two-fer with the National Mall, K-0655.

Photo of Jefferson Memorial

Just steps away is the George Mason Memorial where the Potomac Heritage Trail National Scenic Trail, K-4564 passes right through and is located along the East bank of the Lower Potomac River. The Captain John Smith Chesapeake National Historic Trail, K-4567 runs by as well. The bench I found on the shore of the river met the minimum 100’ rule for both trails and was also located in the National Mall park, so this location was a three-fer.

Photo of George Mason Memorial
View of the Potomac River
Bench along walking path near George Mason Memorial

I tried to travel as light as possible this trip. The gear I chose to bring was the Elecraft KX2 along with the AX1 antenna and my laptop with the USB sound card and CIV cable.

Samsung laptop with Electraft KX2 and AX1 antenna

The January winter weather was mild, in the low 40’s F so setting up and activating outside wasn’t a problem. With it being off season for tourists, I had the park almost all to myself.  There were signs posted at the memorial asking visitors to be quiet and respectful, so the last thing I wanted to do was set up on the steps and draw attention to myself. I found a wall near the Tidal Basin’s water’s edge and was able to set up out of the way of anyone wanting to photograph the memorial, but still be on the property. Continue reading For Conrad, DC Travel = DC POTA!

A Hasty Activation in Georgia

by Teri (KO4WFP)

As many of you know, my personal life has been tumultuous these past five months. I thought maybe it would settle down after the first of this year but no such luck. My son and I moved into a townhouse the third week of January. While I appreciate my parents upending their lives to accommodate the two of us during my divorce, there were too many people in too small of a house with too much stuff. Also, my son needed a room of his own which he didn’t have at their place.

Moves are never convenient and this one was no exception. I needed to be packing the Sunday prior to my early Monday morning move. However, I had already committed to and scheduled an activation at Oliver Bridge Wildlife Management Area (K-3764). The weekend of January 20th and 21st was the winter Support Your Parks weekend and, as a POTA Babe, there was no way I would miss the event!

Support Your Parks information on POTA website

Thankfully, Oliver Bridge Wildlife Management Area (WMA) is only 40 minutes from my parents’ home. That meant another pleasant drive in rural Georgia on GA Route 17 through the communities of Guyton, Egypt, and Oliver.

Google Maps

This WMA consists of 1,560 acres and offers hunting for deer, small game, and turkey. Checking the Georgia Department of Natural Resources Hunting Regulations guide, the only item in season this particular weekend was small game. I would make sure to take the blaze orange vests for both Daisy and me again.

The WMA is bounded on one side by the Ogeechee River, one of the few free-flowing streams in Georgia. This blackwater river runs southeast 294 miles to empty into the Atlantic Ocean at Ossabaw Sound near Savannah. It played an important part for trade and commerce as well as was a source of freshwater and food for communities along its banks. In present day, kayaking and canoeing are popular pastimes on the river as well as fishing.

https://gisgeography.com/georgia-lakes-rivers-map/

Daisy and I arrived at the WMA a little before 11 AM. We took River Road in the park to find a place for the activation. The road was in rough condition in some spots and was another one I’d not want to drive immediately after a heavy rain. I was thankful, once again, for my four-wheel drive Subaru Crosstrek nicknamed Kai. (My family has a funny habit of naming all our cars.)

On the map, there appeared to be a clearing about two-thirds of the way down the road. Tall, skinny pine trees lined either side of the road, not great for getting an arborist line into them. Thankfully, the canopy opened up for a small clearing as I surmised from the map and it was here I decided to set up.

Because of the opening, the pine trees near the side of the road had some lower, reachable branches on them. After a few tries, I snagged the branch I wanted and began hoisting the Tufteln EFRW antenna with the arborist line.

In past activations, I would usually get the antenna up however I could. But, at this point in my POTA journey, I am beginning to think how I want the antenna oriented with propagation in mind. I wanted it to run at a diagonal – northwest to southeast. To do that, I’d have to get it across a wide ditch that was partially frozen due to the cold temps. However, if I just tossed the line across, it was light enough it would likely end up in the ditch where I couldn’t easily retrieve it. Continue reading A Hasty Activation in Georgia

Major POTA fun with the TEN-TEC R4020 and PackTenna 20M EFHW!

The other day, I was thinking…

If  2014 Thomas looked at 2024 Thomas’ QRP radio inventory, he wouldn’t believe the number of radios he’d accumulated in a mere decade.

It’s a little insane, really.

The thing is, over the years, I’ve picked up some great QRP bargains at local hamfests and via various online classifieds. While it’s not exactly “chump change,” you can often find good used QRP radios for less than $300.

Sometimes it’s hard (for me) to pass up those deals.

One such deal was a local fellow who wanted to sell his Ten-Tec R4020 a few years ago.  He listed it for $125, and there weren’t any takers for a few days. (Keep in mind, this was a wee bit before our current CW Renaissance.)

I contacted him and snapped it up. I thought the R4020 might be a fun little two-band radio for POTA and SOTA adventures.

I was right!

The R4020 is an incredibly fun radio to use in the field.

The audio is superb. It has a low noise floor, great sensitivity, and a well chosen filter width. What the R4020 lacks in features, it makes up for with audio fidelity, in my opinion.

I look forward to each and every activation with this QRP wonder.

Speaking of which…

Tuttle Educational State Forest (K-4861)

On Wednesday, January 3, 2024, I made some time in the afternoon to stop at Tuttle Educational State Forest.

I believe I was on the way back to the QTH that afternoon after an overnight with my folks in Hickory, NC.

I love Tuttle, but it had been a while since I completed an activation here. In the activation video (below) I said it had been a couple of months, but later I checked and realized it had been four months! Wow! Hard for me to believe it had been that long!

That day, the park was void of visitors. I was the only person in the parking lot. No surprise here: kids were just heading back to school after a long Christmas break, so there were no field trips on site.

Since there was no competition in the picnic area, I decided to grab a site I might not have actually used before in previous Tuttle activations. I’m evidently working on my WATPT (Worked All Tuttle Picnic Tables) award!

First, a quick inventory…

Before heading to Hickory the previous day, I grabbed the little Blue Ridge Outdoors pouch that held my R4020 and much of the supplies I’d need to get on the air.

I knew, though, that this wasn’t a fully self-contained field kit. Not yet, at least. I hoped that between my main radio gear pack and what I had in the car, I could piece together an entire station.

In my activation video, I speak to the mental checklist I use to make sure I have all of the necessary components to complete my field kit. I did this on site as I set up (typically, this is done prior to leaving the QTH).

Fortunately, I had everything I needed, including an external speaker.

Side note: Some of you might notice the (disproportionately) large Bioenno battery I used during this activation. Yes, it’s crazy overkill for this wee QRP radio. I’d normally use a 3Ah battery, but frankly, I need to exercise my 15Ah battery from time-to-time, too! It gets the least amount of field time because I normally save it for my QRO radios that I use so little in the field.

Gear:

Note: All Amazon, CW Morse, ABR, Chelegance, eBay, and Radioddity links are affiliate links that support QRPer.com at no cost to you.

On The Air

I’d packed my PackTenna Mini 20 meter EFHW with the R4020.

My 40 meter PackTenna EFHW would have been a better choice–since it would have been resonant on both of the R4020’s bands (20 and 40M)–but at the time of day I was operating, I knew 20 meters would serve me well, so 20 meters it was! Continue reading Major POTA fun with the TEN-TEC R4020 and PackTenna 20M EFHW!