At first glance, you’ll see a similarity between the ALT-512 and the LnR Precision LD-11/Aerial-51 SKY-SDR. The LD-11 and SKY-SDR, are very similar, save the LD-11 is marketed to North America (via LnR) and the SKY-SDR to Europe. The SKY-SDR had several iterative upgrades, most importantly the dual-threaded software used in the firmware, which cut CPU latency in half. Both the LD-11, SKY-SDR and now the ALT-512 are made in Europe.
According to Aerial-51, the new ALT-512 is built on the LD-11/SKY-SDR platform, has the same chassis design but has many improvements over the SKY-SDR:
4m Band
4.5 in. Color Display
Improved receiver pre-amplifier
2 transistors in the transmitter PA (was 1)
Waterfall in addition to the Pan-Adapter Bandscope
4 additional front-panel buttons
User friendly front-panel adjustment of often used parameters (formerly embedded within the software menu)
FULL TS-2000 command set implementation
Built-in Sound Card; Digi Modes run using only one USB-2 cable connected to the PC. No additional hardware required.
If the ALT-512 performs as well as or better than its predecessor, it’ll certainly be a great little QRP radio and an excellent general coverage receiver for HF broadcast listening.
Pricing has not yet been posted, but Aerial-51 plans to make this transceiver available in the next few weeks.
CommRadio dispatched this loaner CTX-10 for evaluation and I’m excited to get my hands on it since it’s not everyday I get to evaluate a transceiver designed around field portability (my favorite category of gear).
Yesterday, I took a few shots of the CTX-10 as I unpacked it:
I’ll need to build a fused power cable with the supplied pigtail and also sort out an 8 conductor (Yaesu compatible) modular plug microphone. Of course, I’ll give this radio a thorough review testing it on SSB, CW and digital modes (especially FT8).
Since the CTX-10 is built on the CommRadio CR-1 and CR-1A I anticipate a capable receiver section (in other words, expectations are high). Of course, I’ll test the CTX-10’s ability as a broadcast receiver as well.
From the fertile mind of QRP Hall Of Fame Pete N6QW comes a new Radio Project, the Sudden QRP SSB Transceiver. If you have never Scratch Built such a Rig and would like to N6QW’s latest offering deserves close inspection.
Using only readily available (and cheap) components (and few of them) one can build a Full Blown SSB Transceiver for either 40 or 20 meters. The Radio’s Design will be featured in 2 installments of GQRP’s Sprat Magazine. The 1st being in the Fall issue (Receiver/LO) and the second part with come in the Spring 2019 issue (Transmitter).
One use for the Rig is on the Digital Modes, to that end he has design a simple Digital Adapter (which is also described on n6qw.com). One possibility is for a dedicated FT8 Transceiver!
Even if you do not intend to build the Rig take a moment to check out his Web Page. There you will find a wealth of information on designing and building such Transceivers.
Pete WB9FLW
(not to be confused with Pete N6QW
Thanks for the tip, Pete! How exciting! This looks like an innovative little rig and I love the concept of only using accessible components–in the end, that will give this little rig some longevity.
QRP Labs has just announced the QSX an All-Band All-Mode Transceiver Kit that should be available later this year. The Target price for the 10 Band Model is $150, also available will be a 40 Meter version for $75.00.
Details from QRP Labs:
QSX (QRP Labs SSB Xcvr) is a 40m SSB transceiver with 10-band (160m-10m) and enclosure options. The kit inherits all the functionality of the famous QCX single-band CW transceiver kit but adds SSB, AM, FM, PSK31 and RTTY. This will be the lowest cost all-HF radio available but also high performance and packed with features. These are the planned features of QSX:
Software Defined Radio (SDR) technology with standalone Digital Signal Processing (DSP), no PC required
Very high performance 24-bit Analog to Digital Converter (ADC) and 24-bit Digital to Analog Converter (DAC)
40m (single band) or 160-10m (10-band, including 60m) versions available
Modes: SSB, CW, AM, FM, PSK31, RTTY, WSPR beacon
Power output: 10W from 13.8V supply (power output is adjustable by the firmware)
Single power supply needed, 12V to 14V
USB host interface and connector, for USB keyboard to allow PC-less operation on PSK31 and RTTY
USB device interface and connector, for PC CAT Control
QSX can appear to a PC as a high performance 24-bit USB sound card and radio – for digital modes from a PC e.g. FT8, either demodulated or as I-Q for PC SDR programs
Built-in CW IAMBIC keyer (or straight keying also possible) with raised-cosine key-envelope shaping
1. The ubitx is now available for sale, for $109 dollars (includes the shipping), but only until Christmas. *After Christmas, the price will increase to $129 dollars. for this initial batch, a few ham volunteers and I pitched in to sort the crystals, test the coils, tune-up and box these initial kits, we won’t be able to do that any more. we will have to hire more people (which is not a bad thing) and get them to do it.
2. The ubitx is on sale at hfsignals.com, not hfsigs.com. it is easier to remember. we will soon point hfsigs.com to the new website as well. The new site is in wordpress, that means that we can have volunteers writing and updating it rather than waiting for me to hand code the content in html and vi editor.
3. We need help with proof reading the web content.* If you find any typos, please mail me on farhanbox@gmail.com address (not the bitx20 list),
These apart, the early buyers must be aware that they are beta users of sorts, the firmware will sure get updated. i hope there won’t be any revisions of the PCB.
Pete adds:
Just as an aside the original price of the Heathkit HW-8 was $139.95 (in 1970 dollars) and it became a QRP Classic. The uBITX may become one as well and like the HW-8 there will be (and already are) all sorts of mods/additions one will be able to do. The uBITX is 10 dollars cheaper (after 12/25) works 80-10 M, does SSB in addition to CW, and is a Superhet to boot!
Farhan your hit this one out of the Ballpark!
Very cool, Pete! I am very tempted to purchase the uBITX transceiver before Christmas and have it delivered via DHL service. The only thing holding me back is simply the amount of projects I have on my table at the moment! $109 is an incredibly low price for a full-fledged QRP transceiver!
I’m absolutely amazed that it is also has a general coverage receiver. Perhaps the uBITX could serve the SWL as well as the ham radio operator? I suppose we shall soon find out!
Many thanks to SWLing Post contributor, R. Lewis (KF5GV), who writes:
Just noticed on Universal Radio web page the Comm Radio CTX-10 has been approved by the FCC. They are accepting pre-orders on Dec 1. No indication of pricing but hope they announce it soon.
Thanks for the tip!
I’m looking forward to checking out the CommRadio CTX-10. For one thing, it’s in one of my favorite radio categories: portable general coverage QRP transceivers!
Since the CTX-10 receiver is likely an iteration of the excellent CommRadio CR1 series, I expect it’ll perform well on the broadcast bands as well as the ham bands. I look forward to reviewing the CTX-10.
The “QCX” is a 5W, single-band, high performance CW transceiver kit with WSPR beacon, and built-in alignment/test equipment. It is available for 80, 60, 40, 30, 20 or 17m bands. See below for the long list of features! This is a kit of parts that you assemble yourself. There are NO surface mount components to solder (two SMD ICs are already factory pre-soldered). We do not currently have any enclosure available for this kit, it may be something we investigate in the future.
Features
Easy to build, single-board design, 10 x 8cm, all controls are board-mounted
Professional quality double-sided, through-hole plated, silk-screen printed PCB
Choice of single band, 80, 60, 40, 30, 20 or 17m
Approximately 3-5W CW output (depending on supply voltage)
7-16V recommended supply voltage
Class E power amplifier, transistors run cool… even with no heatsinks
Thank you for the tip, Pete! That’s an amazing amount of transceiver for the price. You’re right, I believe even a new kit builder could build this transceiver.
After rumors surfaced about the demise of the Elecraft “K1” line, Wayne Burdick (N6KR) made the following announcement on the Elecraft email reflector, specifically mentioning the original K1:
We should have made a formal announcement here. Yes, we discontinued it because certain parts are hard to come by now, making it no longer cost effective for us to manufacture.
It was a great product for us, and I used mine for years, taking it on many trips. I thought of it as a “Sierra on Steroids” at the time (referring to an earlier design I did for the NorCal QRP Club). But we’ve moved on to more versatile field radios, including the KX2 and KX3.
73,
Wayne
N6KR
I’ve owned both the K1 and KX1 and they performed amazingly well. I suppose that’s why I also invested in both the KX3 and KX2 transceivers. I suppose all good things must come to an end.
I still own a K2/100 and I certainly hope Elecraft continues to support this fine transceiver. It’s unique in that it’s about the only American-made transceiver kit on the market that’s easily serviceable by a non-technician. It’s also a rock-solid performer and, frankly, has a cult following of its own.
Wow! I may have to purchase one of these and try it out.
I’m currently teaching a HamRadio 101 course to a group of 13 year olds. One of them recently asked how much it would cost to get a basic HF radio kit with SSB mode. HF rigs–even basic ones–tend to be quite expensive if they include SSB.
When was the last time you used a radio you had built? The BITX40 board is single circuit board 40 meter SSB transceiver module. Inside an evening, you can be on-air with this SSB transceiver module, chatting with the local gang or chasing DX. Plug in the earphones, the included electret mic, tuning and volume controls and you are on air! Included are high quality connectors, all the needed sockets and jacks, tuning and volume controls, mounting hardware, etc.
Technicals
The BITX40 is a very clean, crisp and quite receiver. The front-end has a triple tuned circuit that cuts out-of-band signals from getting inside, a diode ring mixer front-end with a very low phase noise, all analog oscillator makes this a crisp receiver that doesn’t overload easily. The all analog signal path to your ear makes provides outstanding signal clarity that is to be heard to be believed.
7 watts of SSB provides you with enough juice to have thousands of contacts on 40 meters, daily rag chew and occasional DX chasing. Any common 2 ampere 12 linear volts supply will provide enough juice for this transceiver. Or you could simply run it from a battery!
Hackable
The BITX40 will inspire you to experiment. Modify it, mount it, tweak it, change it.
The PCB uses all analog large sized SMD components that are laid out on an easy to understand manner on a double sided board with broad tracks. This can be your main module around which you can start experimenting. There are jump-points from where you can add more modules like the DDS, more bands, better audio amplifier, etc. Imagination is your limit. You can separately increase the power amplifier’s supply voltage to 25 volts to be more than 20 watts of power : You will have to add a better heat sink. The mods are on the way!
The board can be installed inside any box that you like. Make your own station rigs, man-packs, trail radios or mount it in a cigar box and leave it on your bedside table. The tuning capacitor has been replaced by a varactor tuning so you can place the tuning knob anywhere as it only carries a DC voltage. Watch the instructions video.
Box Contents
We have tried to include connector/hardware you might possibly need to build a full radio. However, we also had to balance the shipping weight to keep the overall cost down. You will have to supply your own box, power supply and earphones/headphones/speaker.
4-1/2 inches by 5 inches tested SSB transceiver module, covering any 150 KHz segment of the 7 MHz band
Small electret microphone
High quality BNC connector for the antenna
Two earphone style audio jacks for the mic and the earphones/speaker
A set of DC power socket and plug
Volume control with on/off switch
100k linear pot for tuning
4 Brass stand-offs with mounting nuts and bolts
Connectors with wires for all connections on the board
* Note : A speaker is not included in the kit as earphones/headphones/speakers are easily available locally. No cabinet is included to save on the postage cost. Almost any box maybe used.
Manufacture
The BITX boards are hand assembled by a collective of women. Each of the toroids is hand wound. This provides these women with livelihood. The assembled boards are then DC checked a final RF check is performed to check the receiver’s sensitivity as well as transmitter’s output before being shipped. Each board is individually numbered.
[This post was originally published on my other radio blog, The SWLing Post]
As seen from the Overmountain Victory Trail: The Revolutionary War encampment at the Museum of North Carolina Minerals.
As I mentioned in a previous post, what I love about the National Parks On The Air program is that it combines two of my favorite things: national parks and ham radio. My family visits national parks regularly, so it’s easy for me to pack a small radio, do a quick NPOTA activation all while incorporating non-radio activities that the family loves.
Normally, I would set up my station somewhere close to the Museum of North Carolina Minerals which is situated at the junction of these two National Park entities. Saturday, however, was a special event at the museum: a Revolutionary War Encampment.
The Museum is located at Gillespie Gap, an important stop for Revolutionary War fighters on their way to the Battle of Kings Mountain. Each September the Museum hosts an encampment of re-enactors who assume the role of the Overmountain Men, primarily Scots-Irish settlers from Eastern Tennessee and Western North Carolina who came “over the mountains” and ultimately defeated the left wing of Cornwallis’ army at Kings Mountain, South Carolina. Many historians mark this victory as the turning point in the Southern Campaign of the Revolutionary War.
My family loves living history events.
Radio time!
The Park Ranger kindly gave me permission to do the NPOTA activation, but not at the museum itself. She was trying to keep the site set in the Revolutionary War period–a ham radio operator using a portable transceiver doesn’t exactly fit that description. Instead, around 15:30 UTC, I hiked up the Overmountain Victory Trail in search of an operation site near the Blue Ridge Parkway road.
The trailhead was a little rough and overgrown. I didn’t have to trail-blaze, but I did have to wade through a lot of weeds with my gear and my canine companion, Hazel, on leash. It’s times like this I truly appreciate such a compact, lightweight, and packable station.
Can you find the trail in this photo?
Once we entered the woods, though, the trail improved. I found a fantastic spot to operate between the museum and the parkway.
Hazel the dog is a welcome companion does a wonderful job keeping my site free of black bears. She’s patient, too. I typically tie her leash to a small stake or tree next to me and she promptly takes a nap. Here she is admiring my new REI Camping Stool:
You can see part of the EFT Trail-Friendly antenna hanging in this photo.
Setup was quick. I managed to raise the EFT Trail-Friendly antenna in record time. I connected the antenna to the Elecraft KX2 and was on the air, calling CQ on 20 meters in a matter of minutes. In the space of 15-20 minutes, I only managed to work a few stations on the 20 meter band even though I had been spotted several times on the DX Cluster.
I moved to the 40 meter band and logged contacts quickly, however.
My full station and my ferocious guard dog, Hazel.
Hazel, as I mentioned, is a great companion that’s sweet to everyone she meets. She’s happy to hang with me even if I’m just sitting there operating radio for an hour. She’s quiet and doesn’t bark unless she notices a true disturbance.
Still, Hazel does get bored. After I had logged about 20 stations, I heard her gnawing on something. I turned around and discovered that she found the reel of fishing line I use to hang my antennas.
Note to self: next time pack Hazel a bone.
She didn’t even look apologetic or guilty! Oh well…fishing line is pretty cheap to replace and I’m sure she assumed it was a chew toy I had placed there for her.
All in all, it was a very successful activation. In less than one hour, I put 22 stations in the log. The weather was perfect and the whole family had a blast.
A photo I took prior to watching a reenactment of the Battle of King’s Mountain.
What a wonderful day to play radio, take in our national parks and re-live some of our history!
Connecting an international community through low-power field radio adventures.
Please support QRPer by adding us to your whitelist in your ad blocker. Ads are what helps us stay online. All of our ads are ham radio related--no junk, we promise! Thank you!
In the space of 15-20 minutes, I only managed to work a few stations on the 20 meter band even though I had been spotted several times on the DX Cluster.
