Category Archives: News

Antennas, Field Reports, News, POTA, QRP, SSB

Guest Post: Breaking 100 QSOs during two QRP SSB Activations

2 Comments

Breaking 100 QSOs during two QRP SSB Activations

by Joshua (KO4AWH)

Back in May I had to travel last minute for work to North Dakota. I typically bring radio gear in the event that I have some time to do a Parks On the Air activation. This trip presented the opportunity to activate a park in Minnesota as well as one in South Dakota. I didn’t have much time to plan these activations, but I knew I had an early enough arrival in the afternoon that I could likely activate a park in MN and then in SD. So, I picked out a park in MN close to my destination. I could go activate in MN then get over to a park in SD and activate there.

I found a nice looking State Park in MN. The idea was to activate as quickly as I could and then get back to a park in ND with enough time to activate before it got too late. K-2482 Fort Snelling State Park had 110 successful activations. That is always promising when planning out an activation. I got my rental car and headed to the park.

I also had recently purchased a HFJ-350m which is a base-loaded coil with an extendable whip. I found a tripod base I could print online and then designed an adapter so I could install a SO-239 and RG316 lead with a BNC connector. I had just tested this setup in the back yard and knew it worked, although I certainly knew it was a compromised antenna.

HFJ-350m setup on custom tripod in the backyard for testing
Custom 3D Printed Tripod with BNC Connector

I typically bring my Raspberry PI4 loaded with Build-A-Pi and then run digital modes from my phone or Tablet. My plan was to activate this park with the compromised antenna running 5W on FT8 at the first park and then go to my second park and run a full half wave wire in a tree on SSB at 10W.

Not much to say about the activation in MN. The state park was nice but where I set up presented quite a bit of RF noise. Not so much of a problem since I was running digital. After a bit of adjustment on the whip I was tuned for 20m and started hunting a few FT8 stations. I did make a few QSOs while hunting but I then started calling CQ and had a bit more luck. I think because my signal was quite weak, calling CQ was a bit more efficient as only those who could hear me were calling back. While hunting, if those calling CQ were running a bit more power, I was unlikely to get in while running lower power and on a compromised antenna. I got the activation completed with 12 QSOs and packed it up and headed to the next park.

Continue reading Guest Post: Breaking 100 QSOs during two QRP SSB Activations →

News, QRP Radios

Evidently loads of love for the Icom IC-703!

10 Comments

It’s funny: without fail, when I post a new field report or activation video, I get comments from readers about the radio I used during the activation.

“I love that radio…”

“I can’t stand that radio…”

“Why did I ever sell that radio…?” 

If you you follow QRPer.com or my YouTube channel, you’ve likely seen these too.

We’re passionate about our radios for good reason: they’re the hands-on bit…our main interface with our wireless world.

IC-703 Love

Something that has really surprised me are the number of comments I’ve seen from readers and subscribers praising the IC-703.

Since I posted my last activation video, I’ve gotten so many notes on QRPer, YouTube, and via email from those of you who simply love the IC-703.

At least seven of you have told me you still have the original IC-703/+ you purchased new and that you’ll never let go of it.

Impressive!

I love hearing comments like this. The ‘703 is a cool radio in so many respects.

My IC-703 Plus has been a little temperamental and I need to do the Icom-suggested modification that sorts out keyer lock ups. As you’ll see in my next field report, mine does still have issues using end-fed antennas even when using an in-line common mode choke. I could, of course, attach counterpoises to my end-fed antennas and likely mitigate this, but I’d like the ‘703 to be robust enough to handle antennas in my kit just like my other field radios.

I’m convinced the modification will work based on what I’ve read.

Again: great to see all of the ‘703 love! Thanks for that!

Hacks and Hints, News, Portable

How Paul logs while operating pedestrian mobile

2 Comments

Many thanks to Paul (W0RW) who writes with the following tip:

It is a little cumbersome to log your contacts while walking along the trail. For logging and a Dupe Sheet (used in contests) i use a small NFL Type Cuff Log.

You have seen all the Quarterbacks have their ‘Play List’ on their arm. They are on eBay at:

https://ebay.us/E6MK0u

The NFL Play Lists (Cuff Logs) that are on eBay are
‘Read Only’, mine is a ‘Read/Write’.

You have to make your own to be able to write on it.

Mine is a little 3 x 5 card on a metal plate with 2 elastic bands that strap to my left arm.

The metal plate gives me a good writing surface.

There is also a little goose neck LED light that is clamped to the top for Night Ops.

The muff log winterized option!

Paul w0rw

Thanks for sharing this, Paul!

Morse Code, News, Product Announcements, QRP, QRPer Notes, Videos

QRPer Notes: IC-705 Firmware Update, New YouTube Channels, and ARRL Handbook 100th Edition

3 Comments

Because I receive so many tips from readers here on QRPer, I wanted way to share them in a concise newsletter format.  To that end, welcome to QRPer Notes, a collection of links to interesting stories and tips making waves in the world of radio!

IC-705 Firmware Update

Many thanks to Uli Zehndbauer who notes that Icom recently released a new firmware update for the IC-705.

Here are the details/notes about this firmware version from Icom:

Changes from Version 1.27

      • – Displays the Receiving (or Transmitting) route icon (RF or TM: Terminal mode) on the RX History Log and QSO Log
      • – Displays the Receiving (or Transmitting) route icon (RF or TM: Terminal mode) to the chunk information in the QSO audio file
      • – Displays the Receiving route icon (TM: Terminal mode) to the following screens;
        • RX HISTORY screen
        • GPS POSITION (RX) screen
        • QSO audio, PLAY FILES screen
        • QSO audio, FILE INFORMATION screen
      • – Improves the WLAN access point list so that you can delete the connected or saved access points
      • – Improves the CI-V command 1F 01 (DV transmit call sign) so you can set only the “UR” call sign without the other call signs.

Click here to download the firmware from the Icom website.

New CW YouTube Channels/Videos

In the past two weeks I’ve received a number of video links from QRPer readers who are featuring CW activations in their YouTube videos.

First up is Steve (K9NUD) who has started a new channel featuring his CW activations primarily using a cootie/sideswiper. Steve is doing something I wish I had the time to do which is add CW closed captions to his videos. This makes it easy to follow along. Check out this video:

Jonathan (KM4CFT) recently noted in the comments of my YouTube channel that he made a video of his third ever CW POTA activation. I had to check it out and am glad I did. You get a very good idea of what it’s like on the air as a CW newbie. In other words: not that bad at all! Incidentally, when I looked up Jonathan on QRZ, I discovered we have a mutual friend in Zach (KM4BLG).

Keep up the great work, Jonathan!

Chris (KD2YDN) sent me a link to the following video on his new YouTube channel. In the video I actually get to hear what my signal sounded like during his SOTA/POTA activation. He certainly captured some amazing morning scenery and a gorgeous sunrise from Westkill Mountain:

I think you should consider checking out these videos and subscribing!

The ARRL Handbook 100th Edition

The ARRL has announced pre-orders for their new ARRL Handbook. I feel like everyone should have a copy of the Handbook. It’s simply chock-full of useful information–much of which is simply timeless. I still reference the 1994 handbook my buddy Mike (K8RAT) gave me shortly after I got my license in 1997. I feel like it’s important to have reference material like this in paper.

As a side note, I’ve been to a number of shortwave radio broadcast transmitting stations and at each one of them I’ve seen the ARRL Handbook on the Chief Engineer’s shelf. Lots of great radio principles inside.

The book is $80 on pre-order. That’s a lot for a book, but it’s also a LOT of book!

Here’s the announcement from the ARRL:

We have arrived at a milestone. The 100th edition of The ARRL Handbook for Radio Communications is here: Handbook 100. How do you celebrate the most widely used one-stop reference and guide to radio technology principles and practices? By continuing to fill the pages of another edition with the progress and achievement of radio amateurs. Handbook 100 is written for everyone with a desire to advance the pursuit of wireless technology. Here is your guide to radio experimentation, discovery, and innovation.

What’s Inside

Each chapter is filled with the most up-to-date knowledge representative of the wide and ever-expanding range of interests among radio amateurs. There are practical, hands-on projects for all skill levels — from simple accessories and small power supplies to legal-limit amplifiers and high-gain antennas.

Key topics:

    • Radio electronics theory and principles
    • Circuit design and equipment
    • Signal transmission and propagation
    • Digital modulation and protocols
    • Antennas and transmission lines
    • Construction practices

Updated with new projects and content, including:

    • An all-new chapter on radio propagation covering a wide range of bands and modes
    • New and updated sections on electronic circuit simulation
    • New cavity filter and high-power HF filter projects
    • New coverage on digital protocols and modes
    • New material on RFI from low-voltage lighting and other sources
    • Revised sections covering new RF exposure limits
    • New content on portable station equipment, antennas, power, and assembly
    • New material on ferrite uses and types
    • New section on how to use portable SDR to locate sources of RFI …and more.

Click here for more information and to place an order.

Antennas, Field Reports, Morse Code, News, Portable, POTA, QRP

POTA with the Icom IC-703 Plus: Working a serious SWR problem first, though!

26 Comments

If you’ve been here long, you’ve no doubt noticed that I have a sizable collection of QRP radios I take to the field.

Although I have some favorites, I try to rotate all of my radios in the field and even pair them with different antenna combinations as much as possible. If I only owned one field radio, I’d shake things up by pairing my one radio with different antennas deployed different ways during my POTA/SOTA activations.

I get a real thrill out of testing different combinations, actually, and I feel like it keeps me on my toes because I don’t get too comfortable with any one setup in the field.

No doubt, using a wide variety of radios gives me a more informed perspective when beta testing or evaluating new radio models.

That said, there is one radio in my collection that has been overlooked too many times: my Icom IC-703 Plus.

Many of you have noticed this, in fact.  I’ve gotten several emails and comments asking, “So Thomas…when are you taking the 703 out again–?” 🙂

When I purchased the ‘703 from my buddy Don a couple years ago, I imagined taking it to the field very regularly. I always thought it was a cool little radio and with its built-in ATU, it’s quite compact for a tabletop-style rig.

Thing is, each time I’ve taken it to the field, I’ve had issues with the electronic keying that I did not have when using it in the shack. It’s quite sensitive to RF, so end-fed antennas seem to create unwanted dits and dashes in the keyer.

The simple fix, I hoped, was simply using an in-line common mode choke to keep the RF away from the radio. Thing is, the IC-703 has an SO-239 antenna port and two of my common mode chokes are BNC. I meant to purchase a BNC-to-PL-259 adapter at the Shelby Hamfest, but picked up the wrong item (I should have been wearing my glasses).

Then I remembered that my Chameleon 50′ RG-58C/U cable not only has an integrated in-line choke, but also PL-259 connectors. This could work! Continue reading POTA with the Icom IC-703 Plus: Working a serious SWR problem first, though! →

Antennas, Guest Posts, Homebrew, How To, News, Portable, QRP

Sam builds a tiny tabletop HF antenna

18 Comments

Many thanks to Sam Duwe (WN5C) who shares the following guest post:

A (surprisingly good) tabletop HF antenna

by Sam Duwe, WN5C

I recently built a tabletop QRP HF antenna for 17 and 20 meters, in the spirit of the Elecraft AX-1, so I could operate at lunchtime on the campus where I teach. My wants were something small, that would fit in my work bag, that didn’t require a tuner, and could work on a couple of different bands. But on a lark I decided to attempt a POTA activation at Lake Thunderbird State Park (K-2792) pairing this antenna with my Penntek TR-35 QRP CW transceiver. I figured I’d maybe get one or two QSOs and then switch to a long wire in a tree. But what happened amazed me.

I talked to seemingly everyone. Beginning at 9:00 AM September 26th I worked both 17 and 20 meters for an hour and a half and made 37 contacts from across the country. I even had a Swiss guy call me back on 17 but he faded before we could finish. This antenna, at least as a CW POTA activator, works. Granted conditions were very good, but I’ve replicated this multiple times in the past few weeks, just recently at a picnic table in the parking lot of the Route 66 Museum (K-8644) in Clinton, OK (there is quite a thrill in urban activations).

It has also reasonably low profile and very quick to setup and take down. It is also quite a conversation piece when I set it up at school. I elevated the counterpoise by attaching it to a nearby oak and an interested undergrad sheepishly asked if I was listening to the tree!

The build is pretty simple. Physically the antenna consists of a small painters pole from Walmart and an old tabletop camera tripod. I found a nut that fit the screw portion of the tripod and hot glued it into the orange connecting section of the pole. That way the tripod can then be screwed onto the pole. The RF parts of the antenna consist of a 38” telescoping whip that I scavenged from the rabbit ears antenna that came with my RTL-SDR. It connects using the original connector which was hot-glued into a hole I drilled into the top of the painters pole. I found similar small 3 or 4-foot whips from AliExpress for cheap and these would probably work fine.

I then soldered a long length of speaker wire that was wound into two coils: the top for 17 meters (24 turns) and the bottom for 20 meters (25 turns plus the former 24-turn coil). The speaker wire was the soldered to the center of a BNC connector which I hot glued and taped to the pole. I soldered a short piece of wire from the shield of the BNC for the counterpoise and added an automotive spade connector to attach to a 17-foot length of wire. I also included a switch between the coils and the BNC connector to select either just the top coil (17 meters) or both coils (20 meters) using solder, hot glue, and tape.  I then covered my shame in silicone tape.

The most time-consuming aspect of the project was tuning the antenna. It required trial and error to first tune the number of turns on the 17-meter coil and then the 20-meters coil. I extended the counterpoise (for me it’s best when slightly elevated) and the telescoping whip. I performed the tuning with the whip not fully extended to give room to tune in the field. Using a nanoVNA was useful here, as was soldering a pin to the wire to poke through the wire at various parts of the coil to find the best SWR.

In use, the antenna can be affected by both body capacitance and how the counterpoise is situated, so I found that an in-line SWR meter was helpful in making sure all was well. Once set up it is easy to fine tune by just adjusting the whip length. 1.5:1 SWR is about how well I can tune on average. Obviously if you have a tuner you would just have to get it close.

There are a million variation on a small base-loaded vertical antenna, and you can definitely improve upon this design. And, besides the super well-built and elegant AX-1, QRP Guys sells an interesting looking kit, and there are some good 3D printed designs I might want to try out. But regardless how you go about it, it might be worth giving a tiny antenna a shot.

72, Sam WN5C

Antennas, How To, News, Portable, QRP, Videos

Jonathan demonstrates using a K7QO noise bridge and shares a 3D printed OM0ET loop mount

6 Comments

Many thanks to Jonathan (KN6LFB) who shares the following in reply to my recent post about tuning mag loop antennas:

Hi Thomas,

I made a short video showing the use of a K7QO noise bridge from QRPguys to tune a mag loop antenna:

Also, inspired by your post, I dragged my OM0ET magloop up a mountain today for a POTA activation. I used a 3D printed tripod adapter of my own design that allows me to mount it on the collapsing legs from the Buddistick Pro. It makes the whole package a lot more manageable and light weight than carrying a camera tripod.

I had a successful activation of K-4454 on 20 meters, and thought you might enjoy some photos of the setup:

I’ve uploaded the design to Thingiverse at this address:

https://www.thingiverse.com/thing:5589250

73,
Jonathan KN6LFB

Wow! Thank you Jonathan. That short demonstration prompted me to order the K7QO noise bridge kit from QRPguys this morning. In fact, I plan to build this and keep it with my loop antenna as it’ll pair so nicely with my IC-705 and TX-500!

Thank you, also, for sharing those 3D files! I love that field setup at K-4454!

Articles, Field Reports, Guest Posts, News, Portable, POTA, QRP Radios

Mark’s first POTA activation with the Penntek TR-45L

14 Comments

Many thanks to Mark (W8EWH) who shares the following field report:

An Afternoon POTA Activation with the PENNTEK TL-45L

by Mark (W8EWH)

I have a hard time resisting new QRP radios, and I have an equally hard time resisting getting outdoors when late October brings 70F (21C) temps to Michigan.  Days like these are especially sweet given we saw the first snow here last week (no accumulation – but still…). For me there was no better way to enjoy this unexpected weather gift than with an early afternoon POTA activation with my newest QRP radio, the PENNTEK TL-45L.

The TL-45L is the latest radio from WA3RNC, joining the TR-35 and TR-25 in his online store.  It’s a 5-band, 5-watt CW transceiver covering the 80, 40-, 30-, 20- and 17-meter bands.  That in and of itself is not particularly noteworthy.  But when you look at this radio, you’ll immediately see what makes it different.

The retro look for me is unlike anything I have seen in a modern QRP radio.  It frankly looks like it was removed from an Apollo Command Module.  From the front meter to every knob and switch, this radio just begs to be fiddled with.  And each knob and switch serve a function that means no longer needing to dig through menu after menu to find where the narrow filter is switched in because of nearby QRM, or so I can slow down when my CQ POTA is responded to by a slower CW call.

The speaker is located on the (left) side of the radio, a feature many smaller QRP radios don’t have, though headphones can be used via a front mounted jack.  The radio sounds great – I think the radio’s case provides a nice sound chamber.

The TR-45L comes with a couple of options, neither of which I chose to add to my order.  One is a built-in rechargeable battery (5200 mAh), and the other an antenna tuner.  I have plenty of batteries, and normally use resonant antennas.

With the Monday late morning temperature approaching 70 I packed the car with radio gear, and my wife, and we headed out to Island Lake State Recreation Area (POTA K-3315) to activate this park with the TR-45L for the first time.  My wife is not a ham but often comes with me to POTA activations.  While I set up, activate, and then pack up, she enjoys the outdoors with a magazine and crossword puzzle, and sometimes, like today, a light lunch.  Usually, once the activation is complete, we’ll go for a hike on park trails.

Island Lake is about a 20-minute drive from my house.  Its 4000 acres is a mix of open fields and hardwood forests surrounding Kent Lake and the Huron River.  Today it was warm enough that someone was using a paddle board on the lake.

I have found a set of picnic shelters on elevated ground overlooking Kent Lake as a great place from which to activate.  I worked North Pole Alaska from this location on 20M CW using my IC-705 with 10W into an EFHW last May.

Once at the shelter I set up my EFHW (KM4ACK kit) in a sloped configuration using a conveniently located mature tree and my throw line.  It was roughly in an East/West orientation. Over the preceding weekend, I added PowerPole connectors to the provided power cord, and programed both internal CW keyer memory slots.  These are activated using either dit or dah paddle when I toggle Play using the provided switch.   Of course, I did a little POTA hunting using the home antenna to familiarize myself with the TR-45L’s operation.  The learning curve is short with nothing hidden deep behind any menus.

With the radio and antenna ready to go, I set up HAMRS on my iPad, spotted myself on the POTA website, and started calling CQ POTA on 14.0615.  Over the course of the next 35 minutes, I worked a total of 30 stations on 20M and 40M (most on 20M) at which point I basically ran out of hunters.  Not bad for a weekday afternoon.  I packed up and went on a couple mile hike with my wife.

The TR-45L is an absolute joy to use.

I forgot to put it in CW Narrow mode at first, and when nearby QRM popped up, I was able to add this in with the throw if one switch. QRM gone.  (Note, this setting – wide vs. narrow filtering – must not be retained after the power is shut off or the battery is disconnected.)

It sounds wonderful.  I used the side speaker the whole time as my wife doesn’t seem to mind, although the random guy who wandered in with a laptop to get some work done on a warm fall day decided to find somewhere else to work.  There are front mounted jacks for headphones, paddles and a straight key.  Even a rear mounted jack for an external speaker.  The built-in speaker can be turned off and on via a toggle switch.  The two CW memory slots are easy to fill using your paddle.  The front meter can show power output or SWR based on toggle switch position, and you are alerted to high SWR via a front mounted red LED.

I waited a while to get this radio.  Recent supply chain issues caused unexpected delays, but it’s available for order now in factory-built form and most definitely worth the wait.  Kits will eventually be available.  Check out all the TR-45L details here.

Mark Yergin

W8EWH

Field Reports, Morse Code, News, Portable, POTA, QRP, QRP Radios

POTA in the Dark: Problem solving as the sun sets and the clock is ticking on my UTC day

9 Comments

Have you ever had an activation that didn’t quite go to plan?

Yeah. Me too.

Truth is, it’s just the nature of field radio that things sometimes break, behave erratically, and/or some key component goes missing. When you’re lugging your gear around in a pack and deploying it outdoors in a wide variety of settings it’s a much less “controlled” environment than, say, in the shack.

When a problem arises, you have to work that problem in the field to get on the air and complete the activation.

If you watch my activation videos, you’ll note that I try to include everything in them–including mistakes and mishaps.

Mishaps that lead to a failed activation happen less frequently than they did when I first got started in the world of field radio. Over the years, I’ve refined my field kit and made sure I’ve got the right spare components and tools to solve minor issues I might encounter.

That said, I felt like my activation attempt of Lake James State Park on Wednesday, October 5, 2022 was a total comedy of errors. It seemed like an extra layer of complication presented itself each step along the way as I tried to activate that park.

Lake James State Park (K-2739)

The plan was to leave my home around 17:15 local, arrive at the park around 18:00, set up my Icom IC-703 Plus, pair it with a 40 meter end-fed half-wave, hop on the air and work stations until about 19:00 (23:00 UTC) at the latest, then pack up and continue driving another hour to my final destination.

Here’s how it actually played out…

I had all of my bags packed and ready to go at 17:15, but as I was ready to leave, I discovered a plumbing leak under our kitchen sink. It required immediate attention (obviously) so I grabbed my tools, pulled everything out from under the kitchen sink, found the leak, and sorted out the issue. Thankfully, I had some spare plumbing parts at the house. This only delayed my departure about 30 minutes.

I arrived at Lake James around 18:30 and had the entire park to myself.

My real goal at the park was to take the Icom IC-703 Plus out for a little fresh air. It had been ages since I put it on the air in the field. The last time I tried to use it in the field, the internal keyer was tripping up due to a little RF coming back to the radio from my end-fed half-wave. This is a known issue with the Icom IC-703–it’s more sensitive to RF than any other radio I own.

This time, I planned to eliminate the RF with the inline common mode choke built into my Chameleon 50′ cable.

I grabbed my throw line, MM0OPX EFHW and had the antenna deployed in record time.

You can’t tell from the photos because my iPhone does a great job with low-light, but the sun was setting quickly even as I set up the IC-703. I knew I’d be finishing the activation in the dark, but I had a headlamp handy so wasn’t concerned (again, never leave home without a headlamp!).

I turned on the ‘703 and the 40 meter band was chock-full of signals. A very good sign!

Then I switched the 703’s meter to the SWR setting and sent a couple of dits on an open frequency to confirm a low SWR.

The SWR was off the charts poor, pegging the SWR meter at 9:1 (or worse?).

What–?

Continue reading POTA in the Dark: Problem solving as the sun sets and the clock is ticking on my UTC day →

Morse Code, News, Portable, QRP, QRP Radios

When one KX1 is not enough. (For me, it seems.)

27 Comments

If you’ve been following this site for long, you’ll know I’m a big fan of the Elecraft KX1 [understatement alert].

I owned one for the better part of a decade, then sold it to purchase a KX2 in 2016. I almost instantly regretted selling it.

In 2020 I purchased another KX1 for $300; like my previous one, it was a four band model, with ATU and paddles. In fact, it even came with a number of other accessories like a proper Pelican 1060 case.

I made dozens of POTA activations with this little KX1 and named her “Ruby” (because I tend to name radios that are a permanent part of my collection).

Trouble in paradise

In the summer of 2021, though, Ruby started exhibiting some issues. This was not completely unexpected because:

  1. All KX1s started life as a kit. None were factory assembled and tested by Elecraft. Quality varies based on the original kit builder.
  2. I believe Ruby is pushing 20 years old.

The main issue was, after turning on the power switch, the rig wouldn’t completely power up. Instead of the typical two clicks we KX1 owners are accustomed to hearing, I only heard one click and neither the display nor any of the functions worked.

This was an intermittent issue–the next day it might power up as it should. I continued operating and tried to find the issue myself, but my skills at doing repairs on radios is very limited.

I took Ruby to Dr. Vlado who traced the issue to a faulty encoder. I purchased a replacement encoder from Elecraft (along with a number of other spares) and Ruby was back on the air!

Back on the air for a while…

A couple months later, I discovered that power output would drop to nearly zero watts after about 20-25 minutes on the air. Basically, when the radio would get warm from operating, power output was affected.

Vlado traced the issue to a cold solder joint and repaired it (while also double checking other joints). Ruby worked perfectly for a few more activations…then once again the same issue with power output dropping reared its ugly head.

Right before we left for Canada this summer, Vlado found yet another cold solder joint and made the repair.

Once we were back home from Canada, I put Ruby back on the air. I did a lot of SOTA/POTA chasing from home and took her on a couple activations.

All was going well until a few weeks ago (you may see this in an upcoming activation video) when once again, power output took a nose dive after the radio warmed up from operating.

It appears old Ruby is just littered with cold solder joints.

I brought her home and decided that I would pull her completely apart this winter and re-solder every point on her board.

Parts radio hunt

Last year, I started hunting for a second KX1. I didn’t care if it was fully functioning because I was mainly searching for a parts radio.

The KX1 has become–and you’ll know this if you’ve been looking for one as well– as rare as hen’s teeth. When they do appear on the market, they command a premium.

In a full year, looking pretty steadily, I only found one reasonable deal on what sounded like a quality KX1. I contacted the seller and he told me that within the one hour his ad was published, he received 10 offers. He asked if I wanted to be put on the waiting list if all ten fell through.

“Okay, I guess?”

I blame the KX1 price increase on a few factors:

  • Elecraft discontinued the KX1 several years ago. No more are being made.
  • Others are looking for spare KX1s.
  • The CW renaissance we’re going through (truly an amazing thing!)
  • The popularity of POTA and SOTA
  • It is still a very unique and capable field radio
  • And quite possibly me, being so public about my love and admiration of the KX1 (where’s that foot of mine so I can shoot it?)

If you’ve been looking for a KX1, you’ve no doubt noticed the low supply and high prices.

Frankly, I’ve even felt a bit guilty looking for a second KX1 knowing how few there were on the market.

Then an opportunity

A few weeks ago, I was chatting with a friend and–long story short–I discovered that a mutual friend of ours would be willing to sell me his KX1.

It was a three band model with ATU and paddles.

He was the original builder and, in fact, this was the third KX1 he’d built. I know him and his soldering work; it’s top-shelf and professional.

I knew I’d likely never get an opportunity to be only the second owner of a KX1 and to actually know that the builder is one of the best out there.

He offered it to me for a fair price based on the current market.  I didn’t want him to lose money by selling to me, so I agreed.

I’ve already taken the new KX1 on three activations and it’s performing flawlessly. In fact, I believe the built-in ATU is even doing a better job finding matches that the one in Ruby.

I still plan to work on Ruby this winter–it’ll make for a nice relaxing project some cold, snowy day. It’s the same process Vlado would have to go through (and he’d do it without hesitation) but I’d rather do it myself and save his time especially since it’ll be a bit tedious.

Oh yeah. The name for my new KX1?

Meet Ingrid!

Thank you for reading this post (which is arguably more of a confession and justification)! As always thank you for your support.