We’re in the Baie-Comeau area at present, and I’ll only have a short window to fit in this activation before we hit the road again and do a little off-grid camping for a few days!
I’ll be QRP and hopefully on 20 and 40 meters CW. If I have the time (and mobile coverage to self-spot) I’ll attempt to do a little SSB as well. If I can find an adequate tree (they’re not so tall along this trail) I’ll deploy an EFHW, else it’ll be a random wire.
Conditions have been so rough lately, I’m not quite sure what to expect; especially this early in the morning at this location.
This will likely be my only activation for a few days because there are sadly no POTA/WWFF parks nor SOTA summits within easy reach of our campsite along the St-Lawrence.
Update!
Thanks to everyone who listened for and logged me this morning. The activation was a big success. I logged a total of 30 stations on three modes all in very short order.
Thanks so much! Now it’s time to pack the camping gear and go whale watching!
More specifically, I wanted to activate the park by way of the scenic one-way road that starts near the New River Gorge Visitor’s Center and descends down to the Tunney Hunsaker Bridge (the “old” New River bridge).
Why? Because in December 2016 during the National Parks On The Air (NPOTA) program, I passed through West Virginia and activated some very rare parks on my way to a multi-day park run with Eric in Ohio. I fully intended to activate the New River at this very spot (underneath the “new” New River Bridge) after hearing how amazing the drive was from Eric.
Unfortunately, I happened to time my trip through West Virginia on a day when we received about an inch of snow. Even though (at the time) I was driving a Toyota minivan with nearly bald tires, the snow didn’t pose a problem at any other site, save this one. I had to change my plans and activate the New River in a spot where the access had less elevation change on a narrow snow-covered road. With my Subaru, this wouldn’t have been an obstacle in the slightest.
I was looking forward to going back to this site and was very pleased to see that Eric and his son, Miles, had already planned this trip in the draft itinerary!
New River Gorge National Park (K-0696)
On the morning of May 20, 2022, Eric, Miles, Theo the dog, and I left our campsite at Babcock State Forest and made our way to the New River Gorge Visitor’s center next to the New River Bridge.
If you’re ever in this area, I’d highly recommend checking out this visitor’s center as it has some well-designed exhibits detailing the impressive engineering that went into the construction of the New River Gorge Bridge.
There are also some fantastic views from the visitor’s center and from its short gorge overlook trail.
From the trail overlook at the visitor’s center we could see the spot where we planned to activate near the Tunney Hunsaker Bridge deep in the gorge (see photo above).
The drive into the gorge was quite scenic with a number of spots to park and take in the enormity of the New River bridge.At the bottom of the gorge, the view was pretty spectacular as well!
My partners in crime: Eric, Miles and “The Great Warg” (Theo the dog)
Tufteln 9:1 EFRW (End-Fed Random Wire) antenna
I mentioned in a previous post that long-time QRPer.com reader and supporter, Joshua (KO4AWH), runs an Etsy store with a wide range of products primarily designed for field operators.
Besides the Elecraft T1 protection case I mentioned previously, he also sent a couple of his QRP field antennas for testing and evaluation (to be clear: free of charge). Thanks, Joshua!
This year, instead of attending the 2022 Hamvention, my buddy Eric (WD8RIF) and I hatched another plan.
Eric and I–along with his son Miles (KD8KNC) and sometimes Mike (K8RAT)–attend Hamvention every year it’s held. We’d planned to do the same this year especially with it being the first in-person Hamvention since 2019.
As Hamvention approached though, we both had a lot going on in our lives and decided to save a little money, a lot of travel time, and meet in West Virginia for several days of POTA activations and just hanging out. I explain a bit more about the decision in this previous post.
On the afternoon of Thursday, May 19, 2022, we (Eric, Miles, Theo the dog, and I) met at Babcock State Park and set up our tents at the adjoining campsites we’d reserved.
Babcock would serve as our home base for the entire WV POTA expedition.
As a bonus, Babcock State Park (K-1798) is also a POTA entity, so we activated it in the late shift after dinner each evening.
As soon as the tents were deployed that afternoon, we all jumped into Mile’s Subaru with our radio gear and hit our first park!
Beury Mountain Wildlife Management Area (K-7036)
Beury Mountain WMA is so close to Babcock State Park, I have to assume they share a common boundary.
Looking back at last year (2021), if I had to pick out one of the easiest SOTA activations I made, Mount Jefferson would be near the top of the list. It’s a very accessible summit although not technically a “drive-up” summit because you will need to walk a short distance up a service road to the activation zone (AZ).
Mount Jefferson (W4C/EM-021) is located on and protected by the Mount Jefferson State Natural Area (K-3846), so when you activate Mount Jefferson for Summits On The Air, you can also claim the activation for Parks On The Air and World-Wide Flora and Fauna as long as you work at least 10 contacts.
What I love about POTA and SOTA “2-fer” sites like this is that you can set things up to be spotted in both systems (and often the WWFF system, too!) which increases your audience of hunters and chasers, thus increasing your odds of achieving a valid activation in all programs. It’s especially desirable if you’re a CW op and know you may potentially be in a spot with no mobile phone service for self-spotting; if, for some reason, RBN auto-spotting functionality is down with one program, the other serves as a backup.
Mount Jefferson is at least a two hour drive from my QTH, but it was easy pickings on April 29, 2022 because it happened to be within spitting distance of New River State Park where I was camping with my family.
Mount Jefferson (W4C/EM-021)
The drive to Mount Jefferson took all of 20 minutes which was a good thing because our family had other activities in store that day including some extended hikes!
After 12:00 Zulu (9AM Eastern Time USA) Friday, July 1 [2022], and once you have logged into the http://pota.app site, you will notice “My Log Uploads” as an option in our menu. Immense thanks WR5B and N0AW!
Those of us who have been POTA’ing for a few years will find this a very welcome feature!
Up to this point, POTA has been using regional volunteer coordinators to upload logs and they’ve done an amazing job. As POTA has grown–by orders of magnitude over the past few years–the amount of time needed to do uploads is truly significant for those coordinators. In at least one case I know a coordinator’s work load actually cut into their own POTA activating and hunting time.
I’ve always been so appreciative of our coordinators, but always felt hesitant to bug them when I’d discover an error in my logs that required deleting a log entry and re-uploading. I’ve never had a coordinator complain, but I hated to get them involved over a transcription error on my part.
I’m so happy to see that the beta testing has gone so well and the system will be online within an hour (at time of posting Friday morning).
I understand Mike (K8MRD) will soon publish a video here explaining how the new self uploads work.
Many thanks to all of those involved with making POTA what it is today and I’m so pleased to see self uploads being brought online. I would suggest we all be patient if we experience any problems as I suspect the new functionality is going to get a proper workout starting today!
Regular readers of QRPer.com might question the wording in my title since I’ve already posted several field reports and even a full review of the Xiegu X6100. So why would this X6100 be considered a “new” radio–?
Since I go over this in more detail in the activation video (linked and embedded below), I’ll give you the nutshell version here:
My activations with the X6100 early this year (2022) were all performed using a loaner unit sent to me by Radioddity. I kept that unit for a few weeks, shipped it on, and purchased one of my own.
In February, when I received the X6100 I purchased, I immediately noticed a small mechanical issue with the encoder.
This is the X6100 open. You can see the back of the encoder to the right of the ribbon cable.
I tried fixing it (with instructions received from Xiegu) but in the end had to return the transceiver for replacement.
The X6100 unit in this field report is my replacement–technically, the third X6100 I’ve had in my hands, and this was my first activation using it.
Many of you have asked why I haven’t taken the X6100 to the field more often this year and this is why. I basically didn’t have a functioning unit for most of February, March, and April. Radioddity was quite responsive to my issues with the X6100, but frankly I had a lot going on during that time frame so it took longer than normal to troubleshoot, modify, test, and send back the faulty unit.
Fortunately, the replacement X6100 has no encoder issues other than the brake is very tight. I’m not willing to break the warranty seal on this unit to adjust it, so I’ll just live with a much-tighter-than-I’d-like encoder.
[Update: Bob (W0BNC) points out that the tight brake is due to friction caused by a felt pad under the X6100 encoder knob. The remedy is to pull off the rubber ring around the encoder knob, loosen the set screw, lift the knob slightly off the body, and retighten. I’ll do this when I’m back with the X6100 after summer travels. Thanks, Bob!]
X6100 field kit test
This activation was also the perfect opportunity to test all of the components of a dedicated field kit I’m building around the X6100.
Eventually, I’ll replace the speaker wire with some thinner Wireman stuff and it should all fit in the Hound pack, albeit snuggly!
I’ve decided that the X6100 will live at my parents’ home in the NC foothills, so I’ll always have a field radio kit available while staying there overnight.
I took the family on a multi-day camping trip at New River State Park in April 2022. During that trip, I made an activation of New River each day and also fit in a quick SOTA activation (click here to read an overview). I didn’t film all of my on-the-air because some of that radio time was spent sitting around chatting with my family and even some neighbors at the campground.
Since I’ve already posted a summary of that fine trip, and since I’m traveling today, I’ll keep this field report brief(er).
Morning POTA
One thing I love about POTA while camping is how effortless it is to do morning activations. You simply roll out of bed and get on the air. That easy.
The following field report was for an activation session on the morning of April 29, 2022.
I spent the early morning that day brewing a couple cups of coffee and catching up on my QRP Quarterly and QST, then I took Hazel on a short hike.
The weather in/around Québec City has been amazing lately; nice cool mornings and warm, clear days. I know this probably won’t last, so we’ve been taking advantage of it as much as possible (il faut en profiter, as francophones like to say).
Yesterday, we had a few errands to run in town: we needed to pick up some groceries, order a tarte au citron for my birthday (today!) from our favorite patisserie Pralines & Chocolatin Château-Richer, and yes, enjoy the great outdoors.
I wasn’t entirely sure if I’d be able to fit in an activation, but I tucked my KX2 radio pack in the car just in case. I didn’t take the camera because it was family time and if I managed an activation, I didn’t want to film it this time. That, and I have a huge backlog of activation videos I need to publish; I sidelined a lot of my field reports while studying for the Canadian Basic exam over the past month.
Le Domaine Maizerets (VE-5020)
We decided to hit one of our favorite little parks conveniently located on the east end of Québec City (Beauport): Le Domaine Maizerets.
We’ve been to this park a few times in the past to attend a Celtic festival and to meet with friends.
The grounds are beautiful and there are loads of foot paths.
I was a bit surprised it had never been activated because this is a very popular park and even has free entry with free parking.
Keeping it Stealthy
I decided I wanted to stay fairly low-profile while doing this activation. I wasn’t worried about permissions (families, friends and groups meet here for all sorts of activities) but I wanted to see just how stealthy I could be while operating from a park bench in a city park. I don’t get this opportunity a lot because, back home, I’m usually operating from rural state/national parka and in remote game lands.
We found a couple of benches at the edge of the park that very conveniently had perfect antenna trees behind them.
While no one was watching, I deployed the PackTenna 9:1 random wire antenna; the jacket on its radiator is black and simply disappears with trees and flora in the background.
The wire is next to impossible to see from even 5 meters away
The more conspicuous parts of the antenna–the feed point and RG-316–were tucked away behind the park bench.
My high-visibility arborist throw line was hidden behind the tree and out of sight from those walking on the footpath.
From the footpath, you couldn’t see the antenna, coax, nor the throw line unless you were looking for it.
From behind the bench, you could though; in the very unlikely event someone would have walked behind us, it was pretty conspicuous (always avoid antenna tripping points). That and my family would have warned anyone coming near.
The Elecraft KX2 was a natural choice for this activation: it’s all-in-one and incredibly compact. I can also operate it and log using the knee board Carolanne (N0RNM) kindly made for me last year. No picnic table needed.
Operating CW with earphones is insanely stealthy. A CW op makes almost no noise whatsoever.
One of my daughters (K4TLI) was kind enough to log for me on my Microsoft Surface Go (using N3FJP’s AC Log).
Here’s what I looked like to anyone passing by:
Click to enlarge – Photo courtesy of K4TLI
My wife (K4MOI) and other daughter (K4GRL) were on the bench next to us sketching and painting. We looked like any other family at the park simply enjoying the amazing weather.
On the air
This was only my third activation here in Canada using my new Canadian callsign: VY2SW.
I’m still getting use to sending the new call; it flows well for me, but my muscle memory keeps kicking in and I find myself accidentally sending K4SWL. 🙂
Since I’m in Québec but have a Prince Edward Island callsign, I do intermittently add a /VE2 to the end of my call. It’s a fistful (VY2SW/VE2) so I don’t use it with every exchange or CQ.
Conditions lately have been absolutely in the dumps and yesterday was no exception.
When a propagation path opened, it was great, but conditions were very unstable with severe QSB.
I spent the better part of an hour hopping between 30, 40, and 20 meters to scrape together enough contacts for a valid park activation.
40 meters was absolutely dead due to flaring. I tried hunting a few CW and SSB stations there, but if I could hear them, they were barely audible.
20 and 30 meters served me better, but the QSB was so deep and frequent, I had to repeat my exchange on a number of occasions. Some stations would call me with a 599+ signal and after my reply with signal report, they were then barely audible.
Still, I managed to snag my ten with a couple to spare. 🙂
Many thanks to all of you who waded through the ether to reach me on the other end.
QSO Map
It’s interesting looking at the QSO map post-activation. My best DX (EA4B) was easily the strongest station I worked with my 5 watts.
Click to enlarge the map:
This activation was so much fun.
Sure, contacts weren’t frequent but they were all meaningful and, frankly, none of us minded spending time outdoors on such a gorgeous day! It added an extra dimension keeping things very stealthy, too.
Thank you
Thanks for reading this field report. Now that my Canadian exam is in the books, I’ll have time to catch up on the numerous activation videos in the backlog!
Of course, I’d also like to send a special thanks to those of you who have been supporting the site and channel through Patreon and the Coffee Fund. While certainly not a requirement as my content will always be free, I really appreciate the support which allows me to open up my work life to write more field reports and film more activation videos.
I hope you get a chance this week to play radio outdoors or chase/hint some park, island, or summit activators!
You might recall from my previous field report that I took the family on a camping trip at New River State Park in April 2022. During that trip, I made an activation of New River each day and also fit in a very fun SOTA activation (click here to read an overview).
Note that anytime you’re performing an activation over multiple days at any one park, you can only have one activation per UTC day.
I’m often asked if I ever charge my LiFePo4 batteries in the field via solar energy.
Truth is, I’m a big fan of solar, but I’m rarely in the field long enough to need to recharge my batteries via solar when performing SOTA and POTA field activations. It’s easier to charge them at home in advance (often via the solar system at our QTH).
In fact, one of my 3 Ah LiFePo4 Bioenno batteries can easily take me though 3-5 activations or possibly more, depending on the length of the activation and the rig I’m using.
Photo by K4TLI
For longer forays into the field, however, I love going solar.
Indeed, every few years, my family will stay in an off-grid cabin on Prince Edward Island (Canada) for up to 6 weeks at a time. Solar is the only practical way to stay on the air that length of time.
Of course, I also like having a solar option, when doing proper primitive/off-grid tent camping.
In the past, I’ve used a very simple portable solar charging system based on a variety of rigid and folding panels, a Micro M+ charge controller, and sealed lead acid batteries. The batteries are of course heavy, but they work brilliantly for fixed operations.
These days, I’m fully invested in LiFePo4 batteries and my Micro M+ charge controller is not really designed to pair with the BMS (battery management system) in my Bioenno packs.
I contacted Buddipole with a few questions about the unit and to find out when they would be in stock again (at the time, they were on back-order and indeed they are at time posting this report).
QRP radios, product announcements, reviews, news and more. Low power amateur radio fun!
Please support QRPer by adding us to your whitelist in your ad blocker. Ads are what helps us stay online. All of our ads are ham radio related--no junk, we promise! Thank you!
Thanks to everyone who listened for and logged me this morning. The activation was a big success. I logged a total of 30 stations on three modes all in very short order.
