Category Archives: POTA

News, POTA, QRP, SOTA

Unofficial POTA & SOTA Etiquette

11 Comments

I recently saw a post in the POTA Facebook page that reminded me of a question I received from a reader last summer.

This reader asked:

Thomas, I’m new to POTA [Parks On The Air] and also plan to participate in SOTA [Summits On The Air] on vacation later this year. I’m a DXer and avid contester so portable operation is new to me. Can you give me tips about etiquette when chasing and, especially, activating a park or summit? In contesting and DXing there are codes of conduct which I try to always try to follow. 

I though I might post some of the tips I sent him. I also asked for input from some other activators/hunters and they independently confirmed these. I’d welcome any additions you might have in the comments section.

Unofficial POTA/WWFF/SOTA etiquette tips:

  • POTA and SOTA are not timed contests, so it’s okay to slow down and and be patient with hunters and activators.
  • When you hear a Park To Park (P2P) or Summit To Summit (S2S) call:
    • If you’re a hunter, step out of the way in a pile-up and let them through. If the activator asks for your call instead of the site-to-site station, work them but also let them know at the end of your exchange that there’s a P2P or S2S contact in the pileup. Those ops are usually operating in tougher conditions with less power than other hunters. Activators especially appreciate site-to-site contacts.
    • As an activator, give site-to-site stations priority for the same reason.
  • In general, follow the DX Code of Conduct. Most importantly:
    • Never tune up on or immediately next to a POTA activator
    • Wait for an activator to completely end a contact before calling them.
    • Send your full call sign and only send it once.
  • Chasers should note that activators need a certain amount of logged contacts in order to complete a valid activation. In SOTA and activator needs 4 contacts, in POTA, they need 10 for example. With this in mind:
    • Post spots to the SOTA or POTA network if you notice an activator hasn’t been spotted for some time. This will help more chasers find them.
    • If you notice that an activator changes modes or bands, try to work them again especially if you hear that they’re struggling for contacts. Each time you work an activator on a different mode or band, in POTA (not SOTA) it counts as a unique contact for a valid activation.
  • Check scheduled activation plans and frequencies. Not all operators have internet coverage to self-spot and phone operators, especially, rely on hunters looking out for and spotting them.
  • Some notes specifically for CW operators:
    • If chasing a CW activator and you hear a large pile-up, don’t zero-beat the activator’s signal. Rather, move slightly off frequency so the tone of your signal is higher or lower than that of the operator.  On the activator’s side, if every one has a perfect zero beat, it sounds like one continuous carrier as opposed to individual signals.
    • Don’t operate at contest CW speeds as you’ll have a more difficult time making contacts. It’s rare to hear even experienced CW operators in POTA and/or SOTA going faster than 20 WPM.
    • Don’t send a “K” after your callsign when chasing activators–just send your callsign. This is especially confusing to an activator if you have a 2×2 or 1×2 callsign. They may recognize you as W1AWK instead of “W1AW, for example.
  • Unfortunately, you will eventually hear someone intentionally tuning up on an active frequency or deliberately trying to cause harmful interference to an activation. As an activator and hunter, it is important not to “feed the trolls.” Simply ignore them and use it as an opportunity to hone your skills at mitigating QRM and harmful interference. If no one acknowledges a troll, they will abandon frequency much quicker.  Sadly, complaining or asking them to leave tends to egg them on.
  • While it’s actually encouraged to send kind comments and compliments as you chase or activate, keep in mind that activators often have a limited amount of time on site and on the air. As mentioned above, they also need a minimum number of contacts in order to achieve a valid activation. This is not the best time to start a long conversation or rag-chew with an activator. Quite often, there are others who are waiting for you to finish your contact so they can call the station and the activator doesn’t want to offend you by asking you to move on.
  • In general, be patient, courteous, and kind to all chasers and activators. POTA, SOTA, WWFF, and other similar field radio activities feel more like a family or community gathering than a contest.

I’m sure there are other points I’ve missed here. Please comment if you have something to add!

Update: Click here to read Mikel’s (EA2CW) Spanish translation of this article. 

Field Reports, News, POTA, QRP, QRP Radios

POTA Field Report: Pairing the FT-817ND with the EFT Trail-Friendly antenna at Lake Norman

4 Comments

Last week, I thoroughly enjoyed taking the Yaesu FT-817ND to the field.

While the ‘817 lacks features I’ve come to appreciate during field activations like voice and CW memory keying, it’s still an incredibly fun and capable radio.

Last Monday (January 18, 2021), I had an opportunity to visit Lake Norman State Park (K-2740) and perform an activation around lunchtime. Lake Norman is convenient to my hometown of Hickory, NC and these days I typically spend at least a couple nights there doing a little caregiving for my parents. It’s rare my schedule is clear at lunchtime to fit in an activation–typically it’s later in the afternoon.

As with my recent activation at Lake Jame State Park, I paired the Yaesu FT-817ND with my Par End-Fedz EFT Trail-Friendly 40/20/10 meter resonant antenna.

Gear:

It was an incredibly fun activation and one of the few recently where I racked up some great QRP contacts across the 20 meter band before moving to 40 meters.

Here’s my QSOMap of the activation (red lines are phone, green are CW):

As with most of my activations, this one was relatively short. Rarely do I have more than 45-60 minutes of on-air time during a POTA sortie.

I also made another real-life, real-time, no-edit video of the entire activation. If interested, you can view it via the embedded player below or on YouTube:

I’m long overdue a multiple park run, so will start strategizing soon! The Parks On The Air program has also added a few new park in North Carolina, but none appear to be in the western part of the state.

Oh, and Phillip, thanks for prompting me to take the ‘817 to the field again. It is a gem of a rig and I think it might suit your needs very well!

73,

Thomas (K4SWL)

Antennas, POTA, QRP

The importance of quality cable and connectors

4 Comments

Note that this post was originally published on the SWLing Post, but I feel like quality cable is especially important for those of us who are into field activities like Parks On The Air (POTA) and Summits On The Air (SOTA) where our gear gets a lot of handling and outdoor time.

Two radio accessories I often forget to mention in my posts and reviews are cable and connectors. When a cable functions well, it’s taken for granted and easily overlooked.

You’ll hear me say that a radio is only as good as its antenna and while that’s true, the important link in the system is your antenna cable and connectors. If you have a fabulous antenna and a benchmark radio, but you connect the two with substandard cables, it will create unnecessary losses and even shorts if you’re not careful.

But let’s be honest: it’s easy to cheap out on cables.

When I first started using tabletop receivers and transceivers in my youth, I had a tight budget. When I would go to a local hamfest where I’d find excellent prices on cable assemblies from those accessory retailers who sell a little bit of everything.  You know…the tables with everything from $10 multimeters to $5 blinking lights–? I’d find their prices for cable assemblies too attractive and would grab them.

No more.

Back when I owned my original Yaesu FT-817, I used one of these cables on Field Day and blew my finals due to a small short ono a connector end (if memory serves, braiding was touching the conductor). From that point forward, I decided I’d invest in quality cables.

ABR Industries

At the Hamvention in 2010, I found ABR Industries’ table. The only thing they had on display were cable assemblies and a handful of cable accessories. I picked one cable up and inspected it–I could tell it was good quality. Although I know how to make my own cable assemblies (with PL-259s, at least) I appreciate professionally-built assemblies.

I spoke with the representative that day and learned about their company and how they go about making standard and custom cable assemblies in the USA for the consumer, commercial, and government markets.

Although the price was at least double what I would have paid at one of the discount retailers, I never looked back.

From that point forward, I’ve only purchased ABR cables typically at Hamvention, Universal Radio, or even directly from ABR’s website (when I ordered custom assemblies).

The quality of ABR cables is second to none. I have never had one fail at home or (especially) in the field.

For my QRP POTA activations, I started investing in ABR316 and ABR100 BNC to BNC assemblies. I’m especially fond of the ABR316 assemblies (above) because they’re so resistant to memory when I coil them.

You pay for what you get

I suppose this is on my mind because I’m about to do an assessment and make another ABR order so that my new field radio kits have their own dedicated cable assemblies with correct ends (so I’m also not forced to use BNC or PL adapters for matching).

I’m also replacing some of my 3 foot cable assemblies with SMA connectors to PL-259 for my bank of SDRs. This is a part of achieving one of my goals for 2021. I’ll know then that each receiver will have a quality link to my antenna splitter and antenna.

My point here is don’t skimp on your cable, adapters, or cable assemblies.

If you have the skill to build your own, buy quality components and take your time building them.

If you prefer purchasing pre-made cable assemblies, talk with your local ham radio retailer, or seek out cable assembly houses like ABR Industries. I’d avoid purchasing cheap cables you may find on eBay or Amazon.com, for example. That’s not to say that there aren’t quality discount assemblies out there, I just prefer buying from a company that takes pride in their work and stands behind the quality.

Click here to check out ABR Industries. 

ABR Industries isn’t a sponsor of the QRPer (although I’d love to add them!)–I’m just a long-time customer who is happy to plug their products. I can recommend them without reservation.

I’ve also bought numerous long cable runs, wire, DC cable, ladder line, paracord, and sealant from The Wireman. I also highly recommend them.

ABR isn’t the only quality cable assembly house–there are many others throughout the world. Who do you recommend? Please leave a comment and links to your picks!

Field Reports, Morse Code, News, Portable, POTA, QRP

POTA Field Report: Three watts, cold winds, and how *not* to calculate antenna length

4 Comments

Last week, I activated Pisgah Game Land and Pisgah National Forest (K-6937 & K-4510)–things didn’t exactly go according to plan.  I still achieved a valid activations–meaning, I logged ten contacts–but I cut my antenna too short.

I this previous post, I describe my mistake and the lesson learned that day.

In short: I cut my wire antenna too short and my KX1 and KX2 ATUs couldn’t find an acceptable impedance match on the 40 meter band. This pretty much forced me to make do with 30 meters and above unless I modified or switched antennas.

The 40 meter band tends to be my most productive band, particularly on days like last Saturday when I’m operating in the latter part of the afternoon.

Maybe it was stubbornness, but I was determined to make a valid activation with that four-feet-too-short antenna.

Gear:

I first hopped on the air with my Elecraft KX1 (above) and logged a few contacts on 30 meters. I then tried 20 meters, but the band was dead.

Eventually, I pulled the Elecraft KX2 out of the bag with the hope it might actually find a match on 40 meters, but as I said in my previous post, that darn physics stuff got in the way.

That’s okay, though. Although the sun was starting to set and I didn’t want to pack up in the dark, I took my time and eventually logged ten contacts for a valid activation. I actually enjoyed the challenge.

I complain about my wire antenna, but in the end, it made the most of my three watts by snagging stations from New Hampshire, Ontario, Illinois, Arkansas and several states in between.

Against my better judgement, I made a video of this activation. As with all of my videos, they’re real-time, real-life, and have no edits. (They also have no ads.)

A few readers and subscribers had asked me to include the odd video where I actually do a full station set up including the installation of a wire antenna–that’s what you’ll see in this video:

At the end of the day, this was still an incredibly fun activation.

This was the first time I’ve ever completed a valid activation only using the 30 meter band.

Next time, though, you’d better believe I’ll cut my antenna to be the ideal length for 40 meters and above!

How long?

If you use a similar antenna with your KX1, KX2, KX3, or other transceiver, I’m curious what lengths you find work best for 40 meters an above. Bonus points for 80 meters. Please comment!

Antennas, Field Reports, News, POTA

Mistakes and miscalculations might make us better field radio operators

3 Comments

I don’t know about you, but part of the fun of playing radio in the field are the inevitable frustrations.

It might not feel like it in the moment, but when I eventually overcome the challenges of a mistake, I feel like I’ve truly accomplished something.

That was my little epiphany this morning: making mistakes has perhaps made me a better radio operator. Less-than-efficient field deployments have honed my skills and had a major influence on the gear I pack.

If you’ve read some of my (rather rambling) field reports in the past, you’ll note that I rarely do field activations with the exact same gear combinations each time. I feel fortunate enough that I can pair different radios with different antennas and different accessories.  I get a small thrill out of not knowing exactly how well a combination will work, especially if I’m not activating a rare all-time new park or tough summit for that matter. In cases where getting to the site is a challenge in and of itself, I want to use a trusted combo of gear.

It’s that wee bit of mystery that attracts me to the field.

If I approached POTA more like a contest–where activation and contact numbers were my focus–I would have installed a mobile HF rig in my car a long time ago. I could rack up way more parks and contacts that way. It especially simplifies multi-site activation days since it effectively eliminates the time involved in setting up and later packing up gear.  Mobile operating is the most efficient way to hit number goals: drive up to a site, start calling CQ, work your stations, then move on.

K-6937 & K-4510

(Photo credit: K4TLI)

Yesterday, I did a last minute “two-fer” activation of Pisgah National Forest and Pisgah Game Land. I had not planned to do an activation that day–temps never rose above 29F (-2C) at the QTH day and it also snowed and flurried all day long. Winds were very gusty as well, so it effectively felt much colder on the skin.

I wanted to hike up to the ridge line behind my QTH and do the activation but I knew up there temps would be lower and (worse) winds much stronger. Cold doesn’t really bother me, but strong winds do. This was also the first weekend my ankle felt almost normal after twisting it badly last month. It’s healing and I hope will be in shape for a long hike from my QTH to a six point SOTA summit next weekend with my daughter (K4TLI).

All of those factors combined pointed toward simply staying at home, drinking coffee, and reading a book.

Hazel was ready for some field radio fun, though. (Photo credit: K4TLI)

But I really wanted some outdoor time. And I really wanted to make an activation with my Elecraft KX1, so I decided that instead of hiking up in elevation 800 feet, I’d drive down about 900-1,000 feet to a forest trailhead. That would get me on the air in a protected valley with less wind,  less snow, possibly warmer temps, and much less hiking which would be easier on my ankle.

The Last-Minute Antenna

When I use the KX1 in the field, I typically pack a very simple antenna: one length of radiator wire and one length of counterpoise wire–connected to a BNC binding post adapter, I let the built-in ATU sort out the match.

When I owned my first KX1, I had a magic length of radiator wire (the length of which I can no longer remember) that seemed to work amazingly well  on 40, 30, and 20 meters.

My new-to-me KX1 came with two lengths of wire: one 23′ and one about 20′. Although I made a fun and successful activation with this setup, the radiator was simply too short for the KX1 to find a decent match on 40M.

On the way out the door, I decided to cut a new radiator and counterpoise out of scrap wire I use for antenna experiments.

Being a bit stubborn and also in a hurry to beat sunset, I did no Internet research to sort out the ideal lengths for 40 meters.  I simply cut a 17′ length for the counterpoise and about 27.5′ for the radiator.

In the Field

After arriving on site, I deployed the antenna and tried finding a match on 40 meters with the KX1’s internal ATU.

No go.

I tried a few times hoping maybe the ATU would find something even semi-reasonable in terms of a match, but there simply wasn’t enough radiator to make it work. That was a shame because forty meters would have been the ideal band for yielding quick contacts this time of the afternoon.

I had options, but I wanted to make what I had work.

The activation took time and patience. The 30 meter band was now my best bet and it’s where I logged all ten contacts for a valid activation. I tried 20 meters where I had a 1:1 match, but the band was dead.

At one point, I switched out the KX1 with my KX2 that I also packed. I tried to find a 40 meter match with the superior KX2 ATU, but physics got in the way again. 🙂

40 meters was an option

Let’s be clear here: I could have easily cut 4′ off of the counterpoise and attached it to the radiator and I bet I would have gotten a match on 40M. Since the counterpoise was lying on the ground, its length was less crucial.

The EFT Trail-Friendly end fed antenna was also in my pack.

I also had a perfectly capable 40/20/10 en-fed antenna in my pack. Switching out the antenna would have only taken four minutes.

I bet I could have easily yielded 20 additional contacts on 40 meters because the band was in great shape. Almost without fail, 40 meters is my most productive band.

Working with limitations

Thing is, I’m starting to understand that I like working with self-imposed limitations.

Perhaps this is why I love QRP and low-power radio so much: I get a little thrill out of doing more with less.

Yesterday, even after I realized it would be a struggle to log my final three contacts on 30 meters, I persisted. One motivation was I’ve never completed a full activation using only 30 meters. With a little patience, I knew I could snag my ten contacts.

The only things making it a challenge were the facts that temps were dropping rapidly, winds were picking up, and the sun was setting. Hazel (the POTA dog) who so eagerly jumped in the car when she saw me put on my hiking boots earlier, was also starting to shiver.

Fortunately, after trying another short stint on 20 meters, I returned to 30 and worked two more stations in quick succession giving me a total of nine contacts.

It started to get darker, so I hunted and found an operator calling CQ  on 30 and simply made contact with him. He wasn’t a POTA station, just a general CQ call. He kindly gave me his details for the logs.

Lessons learned

I made a video of most of this activation and will upload it when I have a little bandwidth to do so. I’ll embed it in a shorter field report here on QRPer since I’ve described so much already.

Even though it was a challenge making ten contacts to accomplish a valid field activation with my time constraints, I’ll admit that I really enjoyed the challenge.

Next time I head to the field with the KX1, I’ll actually test the antenna prior to leaving the QTH.

In fact, I’m planning to make two radiators: one at an ideal length for 40 meters and above, and another–much longer–for 80 meters and above. Any advice and personal experience from KX1 owners would be much appreciated.

Perhaps most importantly, it’s only now dawned on me how much I enjoy making the most with self-imposed limitations or “trying to make lemonade with lemons.”

Do you feel the same? I’d love to hear your comments.

Field Reports, News, POTA, QRP

POTA Field Report: Pairing the Mission RGO One with the Chameleon Emcomm III Portable Antenna

Leave a comment

While I tend to use small, field-portable transceivers on many of my Parks On The Air (POTA) activations, I also love using  tabletop transceivers when I have a picnic table available or decide to use my portable table. Tabletop radios often provide more power output when needed and better audio from their built-in speakers.

Although I have an Icom IC-756 Pro transceiver, and an Elecraft KXPA100 amplifier that I can pair with my KX2 and KX3 (or any QRP transceiver for that matter), my favorite tabletop fiel;d radio at present is the Mission RGO One 50 watt transceiver.

If you’re not familiar with the Mission RGO One, I’d encourage you to read my comprehensive review over on the SWLing Post.

In short: it’s a brilliant, simple, tabletop transceiver that’s very happy in the field and a pleasure to operate. My RGO One has the optional built-in antenna tuner (ATU). The rig designer is allowing me to keep this unit on extended loan as I help him evaluate and test updates and upgrades.

While I’ve used the RGO One on numerous POTA activations, I don’t believe I’ve ever made a video of it in use, so I decided to change that last week with another one of my real-time, real-life, unedited (lengthy!) videos of this activation (see video below).

Lake Norman State Park (K-2740)

As I’ve mentioned before, I love activating Lake Norman State Park because it has numerous spots for setting up my gear. While I actually prefer activations that require a bit of hiking, it’s nice from time-to-time to activate a state park that has so many widely-spaced picnic tables under tall trees.  That, and my right ankle is still healing after I twisted it in December, so I’m avoiding any proper trail hiking until it is better.

I made this activation of K-2740 on January 4, 2021.

Gear:

On the Air

This was my first activation of 2021!

Since I have Internet access at Lake Norman, I can check out the  POTA spots page on my phone or tablet and self-spot as well as see spots of other activators.

When I have Internet coverage like this–and I’m not pressed for time–I try to work as many Park-To-Park contacts as I can before I start calling CQ POTA myself.

As I mention in the video, one of my 2021 goals is to obtain a valid activation of each park with only five watts or less. This means that each time I start an activation, at least my first ten stations logged will be with a max of five watts of power. I would actually make the goal for all of my 2021 activations to be 100% QRP, but I evaluate gear regularly and part of that process is to push wattage limits so it’s simply not realistic.

This isn’t actually a crazy goal because a number of my transceivers max out at five watts or less, and I know it won’t be an impediment as I activate parks in CW.

In SSB, though? It makes it a bit more challenging, but certainly not impossible and I’m always up for a challenge!

So I started this activation by trying to work a few Park-To-Park contacts but first cranked the RGO One power down to five watts. Trying to be heard over other hunters in SSB was difficult, but CW was much easier.

After working a few P2P stations, I started calling CQ on the 40 meter band in SSB. I worked about four stations, then switched to CW and worked seven more on 40 meters.

Since I’d snagged my ten contacts for a valid activation, I moved up to 20 meters phone (SSB), cranked up the power to over 40 watts, and started calling CQ POTA and racked up an additional 11 contacts for a total of 26 contacts logged at this activation.

Here’s my QSOmap:

Click to enlarge

Note that I left the callsign labels off the map this time to make it a little easier to see the geo location of the stations I worked.

Real-Time Video

I made a video of the entire activation and posted it on my YouTube channel. As with my other videos, there are no edits and no ads. It’s all real-time and includes my many goof-ups! But hey–mistakes are all a part of a real activation!

Again, if you’d like to know more about the Mission RGO One, you might check out my review on the SWLing Post.

Feel free to comment with your thoughts or questions and thank you for reading QRPer.com!

Articles, How To, News, Portable, POTA, QRP

Parks On The Air Pro Tip: Finding more park sites to activate

5 Comments

Many thanks to QRPer, Curt, who recently left the following comment on a recent post and noted:

I too was a NPOTA activator. My first HF contact ever was on 9/10/2016 and then I threw myself to the wolves so to speak activating my first park on 11/12/2016.

When NPOTA was over I went into withdrawal and I thought POTA was going to fill that void but here in Western PA there’s not much to pick from. We have a lot of parks but none that fall into the park list. One of the local parks I’ve been told not to bother because it’s in the middle of the city and the local police don’t seem to like any activations there for whatever reason.[…]

You’re right, Curt, and I totally understand.  Many local, county, and private parks are not included in the Parks On The Air (POTA) program. POTA tends to include parks that are on a state, provincial, or national level. Not always in every country, but it’s the general rule of thumb.

I don’t know the POTA scene in western PA well because I’ve never thoroughly researched it. With that said, I’m willing to bet there are more accessible parks in your neck of the woods than you might realize at first blush.

The only entry to this state park is very easy to find and marked well along the highway.

Historic sites and parks–both state and national ones–tend to have very defined borders with conspicuous entry points. They’re, in many senses, “low-hanging fruit” for POTA because they’re super easy to find and usually have picnic and camping areas.

You simply locate one on the POTA map, tell your smart phone to take you there, arrive, find a picnic table or parking area near trees, setup,…et voilá! You’re on the air and activating. Typically, a very straight-forward process.

I would suggest new POTA operators start with these types of parks to give their field radio kit a good shake-out.

Digging deeper…

There are so many other POTA entities out there, though, and the POTA map (while an excellent resource) can’t represent them well.

I should add here, that POTA is an international radio activity and I do not know the various types of parks and POTA entities in other countries. There’s a lot of variability.

Here in the States, aside from parks and historic sites, we have other POTA entities like:

  • Game Lands
  • Rivers
  • Trails
  • Wildlife Management Areas & Refuges
  • Recreation areas
  • Conservation areas
  • and Forests

These types of public lands can be vast with many possible parking areas and entry points. Some have multiple, disconnected tracts of land and the POTA map only typically represents them as one clickable geo point because it would be incredibly difficult to represent them otherwise.

It requires the POTA activator to do a little planning and research.

One example

Here in North Carolina, we have a lot of state game lands and they’re some of my favorite spots to activate.

Some game lands may only be a couple hundred acres large, others may encompass hundreds of thousands of acres.

Case in Point: Nantahala Game Land is only one entity on the POTA map, but it is located in no less than six western North Carolina counties–dominating the majority of them, in fact.

Check out this map of Nantahala Game Land from the NC WRC website below:

Click to enlarge.

There are probably hundreds of spots where you can find public access to activate this particular POTA park.

Trails are another POTA entity that should not be overlooked. They often snake through areas and have multiple trailheads where you can easily find parking and ample room to activate.

Here’s how I find the more elusive POTA parks…

Being a bit of a map geek, I actually love this process!

1. Take a close look at the POTA list

The POTA map is amazing, but as I said, it simply can’t display the size and geographic shape of each park.

Start with the complete list of POTA entities in your location.

An example from Pennsylvania.

Click here to display a list of all POTA entities at your location.

If you have lived the majority of your life where you are now, you’ll likely recognize some of the names associated with the park entities in this list.

Regardless, comb through this long list carefully. Do an internet search on the park names and you’ll quickly discover roughly where the land is located

2. Make a spreadsheet of potential parks

A sample of my park spreadsheet from early last year.

On this sheet make column headers for at least:

  • The park name
  • The POTA designator for that park (K-6937, for example)
  • The travel time to the park
  • The geo coordinates of potential activation spots

I also added

  • How “rare” the park might be (how many times it’s been activated)
  • How easy access to the park might be
  • If it could potentially be a two-fer (meaning two POTA entities overlapping)

3.) Find an activation site with Google Maps satellite view

Now that you’re developing an activation plan (via your spreadsheet), and you’ve located all of the nearby parks, game lands, wildlife management areas, trails, refuges, etc. it’s time to research each entity and find activation sites.

Most states (and provinces, counties, regions) have sites that will help you find access points to public lands. Each state is different–some (like North Carolina) have amazing online resources, others may not.

If you can’t get the details you need online, don’t hesitate to call those public departments in charge of the lands and ask them about access points. They’re experts on the subject and often your taxes pay their salary. 🙂

To find game land activation sites in North Carolina, I first go to the WRC Map and click on a site. The WRC site will offer up maps and even indicate obvious parking and camping locations.

I then find public roads in/around the game lands and do a Google Map search (you can pick your favorite mapping tool).

I compare the WRC map with the Google map (side by side) and search for parking spots using a satellite view.

Here’s how to find the satellite view on Google Maps using a sample POTA site:

Find the park area based on public roads, then click on satellite view:

Now you’ll be able to see a bird’s eye view of the land:

When you zoom in, you often can identify a nice parking spot:

Using the satellite view I can zoom in and see that there’s a parking space with trees surrounding it. Score!

That’s how I do it.

Important note: of course, it’s incredibly important that you compare public land boundaries with your activation site and make sure you will, indeed, be on that POTA entity when you activate. While there are no POTA police–nor will there ever be–I personally want to be 100% sure I’m activating entirely within the boundaries of my chosen park. Google Maps can’t be trusted to indicate unit boundaries–one needs to compare the state or federal maps of the unit to be sure.

Next, I take those geo coordinates (map links) and embed them in my POTA spreadsheet.

Later on, when I decide to activate that park, all of my research is done! I simply grab my gear and go.

That’s it!

If you’re like me, you may be surprised how many potential activation sites there are in your region when you take a closer look at public land boundaries and access points.

I found at least five POTA sites within a 90 minute drive of my home that were ATNOs (All-Time New Ones) that no one had activated.

How do you research parks–?

I probably should not call this a “Pro Tip” because I’m not a professional!

There are many different ways you can find great POTA sites within your region. Please feel free to share your POTA procedure with us in the comments!

Field Reports, News, POTA

POTA 2020: Taking a look at my stats

6 Comments

A few days ago, I checked out the leaderboard statistics on the POTA website to see exactly how many parks I activated and hunted in 2020.

This was one of the first times I’d checked my numbers in weeks. At the end of the day, I’m not a competitive guy, and perhaps one of the reasons I like POTA is it’s more an activity, less a contest.

National Parks On The Air (NPOTA) in 2016 was not a contest either, per the ARRL, but it felt more like one since it was a one year event. I definitely caught the NPOTA bug that year and mostly within the space of 5 months activated over 90 parks. It helped that my girls’ school bordered a national park.

One of my first NPOTA activations in 2016 with buddy Eric (WD8RIF).

Don’t get me wrong, NPOTA was AMAZING fun, but I had some serious withdrawal by the end of the event and even felt a touch of burn-out.

Turns out, so many NPOTA participants had withdrawal, that they formed POTA and even turned it into a non-profit organization.

POTA is a multi-year activity and is also international unlike NPOTA.

I do believe POTA has injected some much-needed life into amateur radio and has given operators a reason to take their radios to the field.

Back to the numbers

With all of that said, I was eager to see what my numbers looked like for 2020, so I checked out my entry on the leaderboard:

Activations

Here’s a breakdown of my activation numbers:

  • 86 Activations
  • 37 Unique Parks
  • 1721 total contacts:
    • 999 CW
    • 0 Data
    • 722 Phone

I found these numbers very interesting.

First of all, had I worked one more CW station, I would have made 1,000 contacts! Still: I like the ring of 999.

These numbers show me that CW has, indeed, become my favorite mode. I’ve only been activating in CW since July 2020 and it still overtook my total number of phone contacts.

The venerable Mountain Topper MTR-3B

To be clear, though: I love SSB and CW equally.

Thing is, I have come to appreciate how effective CW is when operating at QRP levels. Also, it’s much easier to find a clear spot on the dial to call CQ in CW–SSB, some weekends, it can be a real challenge

In addition, as long as I schedule my activation in advance, the POTA spots page will auto-spot me by pulling my details from the reverse beacon network (RBN). This is HUGE for me since a good 60% of the parks I activate have no mobile internet connectivity.

SSB, however, has much greater numbers in terms of operators. I’d be willing to bet there are seven SSB-only operators to every one operator who uses CW.

Phone activators sometimes amass DXpedition-like pile-ups. It’s pretty amazing.

No doubt, if you want to really pump up your POTA numbers, the best plan is to use both phone and CW.

Hunter Stats

I’m a very casual POTA hunter, still the numbers were less modest than I had assumed:

  • 281 Unique Parks
  • 337 Total Contacts
    • 203 CW
    • 1 Data
    • 133 Phone

POTA 2021

As with 2020, I won’t pay a lot of attention to my numbers. I do have a few goals, though:

  • Achieve all of my activations with five watts or less
  • Get my daughter K4TLI in on the POTA action (she’s close to taking her General test)
  • Make at least one data mode activation
  • Go to at least 20 new parks
  • Continue to have fun!
K4TLI logging for me like a champ

To be clear about my five watt challenge: I will use more than 5 watts in the field (indeed, I did yesterday). I often test transceivers and antennas during POTA activations, so need to push the power settings from time to time.

My goal is to work my first 10 contacts (thus achieving the required amount for a valid activation) of each activation with 5 watts or less.

How about you?

If you’re a POTA activator or hunter, have you looked at your numbers recently? What are your goals for 2020? If you’re new to POTA, do you plan to join in on the fun this year? If so, what equipment do you plan to use?

Please comment!

Antennas, Field Reports, Grab And Go, News, Portable, POTA, QRP

POTA Field Report: Pairing the Elecraft KX3 with the AX1 antenna and seeking distant stations

16 Comments

Although I’m a huge fan of wire antennas in the field, since I started using CW during my Parks On The Air (POTA) activations, I’ve really enjoyed experimenting with compromised portable antennas.

Typically, there’s a trade off with field antennas:

High-performance antennas tend to take more time to install. Some of my highest performance antennas are dipoles, doublets, delta loops, and end fed wire antennas. All of them require support from a tree if I want maximum height off the ground. Some (like the dipole) require multiple supports. While I actually enjoy installing wire antennas in trees, it typically takes me at least 10 minutes to install a wire antenna if it only needs one support and one counterpoise.

Compromised or low-profile antennas may lack performance and efficiency, but are often much quicker and easier to deploy.

In my opinion, field operators should keep both types of antennas in their arsenal because sometimes the site itself will dictate which antenna they use. I’ve activated many sites where wire antennas simply aren’t an option.

That was not the case last Tuesday, however.

Tuttle Educational State Forest (K-4861)

On Tuesday, December 29, 2020, I stopped by Tuttle Educational State Forest (K-4861)–one of my favorite local state parks–for a quick, impromptu activation.

I had no less than four antennas in my car that day and Tuttle is the type of site where I can install pretty much anything: they’ve a spacious picnic area with large tables, tall trees, and parking is close by. Tuttle is the perfect place to deploy not only a large wire antenna, but a large radio if you wish since you don’t have to lug it far from the car.

But en route to Tuttle I decided to take a completely different approach. One of the four antennas I had in the car that day was the Elecraft AX1 antenna.

Without a doubt, the AX1 is the most portable antenna I own. It’s so compact, I can carry it in my pocket if I wish.

When I first purchased the AX1, I was very skeptical and assumed it would only work when “the stars aligned”–days with better-than-average propagation and lots of POTA hunters/chasers looking for me.

The first time I used the AX1 in the field, it impressed me (understatement alert).

The second time, same thing.

In all of my AX1 activations, however, I had only operated on the 40 meter band where the antenna’s footprint looked more like a NVIS antenna than a vertical. Meaning, most of my contacts were in neighboring states like Tennessee, South Carolina, Virginia, and Georgia (typically, those states are in my 40 meter skip zone).

The reason I hadn’t tried 20 or 17 meters with the AX1 is because I would start an activation on the 40 meter band and accumulate enough contacts to achieve a valid activation. Since I’m often pressed for time, I simply didn’t bother configuring the antenna for the higher bands.

Time for that to change!

The question I wanted answered at Tuttle: could the AX1 antenna work “DX” stations? By DX, I mean POTA DX, so distant states and provinces primarily–not necessarily other countries.

Gear:

On the air

I paired the Elecraft KX3 with the AX1 at Tuttle. This was the first time I’d ever tried this particular transceiver/antenna combo.

After setting up, I started on the 20 meter band and called CQ for a few minutes.

The first two stations I worked were in Texas (KF9RX and K5RX).

The third station (W6LEN) was in California.

California!?!

Honestly, it was/is hard for me to fathom how in the world 10 watts into a tabletop telescoping whip antenna could work a station exactly 2,083 miles (3,352 km)–and three time zones away–from my picnic table. I’m sure W6LEN has a great antenna on the other end, but I bet he would be surprised to learn that my 10 watt signal was being radiated by such a wee antenna.

 

 

I then worked stations in Florida (K2WO), Minnesota (N0UR), and New Hampshire (W2NR) and decided to move to 17 meters.

On 17 meters I worked W2NR in New Hampshire once again.

I should note here that each time you work a station on a different band or with a different mode, it counts as a separate contact in POTA. In other words, my contacts with W2NR on 20 meters and 17 meters counts as two logged contacts toward my overall QSO count. I’m very appreciative of hunters who go out of their way to work me on different bands and modes: those extra contacts help me achieve a valid activation in short order.

I then moved to 40 meters and worked stations from Tennessee, West Virginia, Ohio, and Michigan.

Video

Here’s a video of the entire activation. It’s a long video as it starts at set-up and continues until my last contact. There are no edits in this video–it’s a real-time, real-life deal and contains all of my bloopers:

Note that in the video I had the KX3’s volume maxed out so that it could be picked up by my iPhone microphone. The KX3’s wee internal speaker was vibrating the chassis ever so slightly. On the 40 meter band, it resonated enough that it moved the encoder slightly. Next time, I’ll plan to bring a portable external speaker (if you have any suggestions of good ones, let me know).

And here’s a QSOmap of the activation:

Click to enlarge.

Bioenno 3aH LiFePo battery

I should also add that I’m very pleased with my new Bioenno 3aH LiFePo 12V battery. You can see it in the photo above–it’s slim, lightweight, and very compact.

I purchased it during Bioenno’s Black Friday sale. I was a little concerned it might not have enough capacity to carry me through multiple activations–my other LiFePo batteries re 4.5 and 15 aH–but that does not seem to be the case at all! Not only did it provide nearly an hour of intense use on this activation, but it also powered three activations the previous day–all four activations on one charge! Brilliant!

Radio magic

As I mentioned in a previous post, this was one of those activations that reminded me of the magic of low-power radio. It was incredibly fun!

For all of those phone/SSB operators out there, I will eventually see how successful I can be doing a phone-only activation with the AX1 antenna. I’ll plan to make a video of it as well. I’ll need to plan this for a day when I have more time to spend on the air and at a site where I know I’ll have internet access to spot myself to the POTA network.  SSB isn’t quite as effective as CW when operating with a setup this modest. Still–it can be done! It just requires a little more patience. Please let me know if this sort of thing would interest you.

Until then, Happy New Year and 73s to everyone!

Cheers,

Thomas (K4SWL)

Morse Code, News, Portable, POTA, QRP

The magic of low-power amateur radio never dies

1 Comment

I’ll keep this post short and sweet because I plan to write up a full field report with video sometime next week.

Tuesday (December 29, 2020), I fit in an impromptu Parks On The Air (POTA) activation in the afternoon. The station was very modest: basically, my Elecraft KX3 paired with the super compact Elecraft AX1 antenna.

Here’s what I did with 10 watts and a wee telescoping whip during mediocre propagation:

I got a huge thrill out of this.

Honestly, this hobby never gets old and I honestly believe there’s magic in QRP!

Here’s wishing everyone a safe, healthy and happy New Year!