Stealthy field activations, for me, aren’t about activating where I shouldn’t (in fact, by definition, activations can only take place on public lands) it’s just fun!
As I’ve mentioned before, when I choose to be a bit stealthy, it’s strategic. I consider one of the privileges of doing POTA and SOTA activations is that I’m often the first ham others encounter out in the wild. It gives activators like me a chance to be a ham radio ambassador. I like giving our wonderful past time a proper introduction and even enticing others to join in on the fun.
That said, there are times when my on-the-air time is very limited and I want fewer interruptions. That’s when being a bit stealthy can help me get in/out quickly.
It simply attracts less attention.
I tend to be less conspicuous in a park when I’m in a busy area with lots of people and activity. I don’t want my operation to get in the way of others’ enjoyment of a park. I don’t want someone to trip on or get tangled up in my wire antenna while tossing a frisbee, for example.
Also, when it’s super busy and I’m pressed for time, I’d rather get the activation done and then move on.
This granted me full HF privileges and I even obtained the callsign VY2SW within an hour of requesting it the following morning.
No visit to Ottawa would be complete without snagging this photo!
Of course, I was very eager to use the new callsign on the air!
Finding a park
A few weeks prior to our trip, I checked out all of the POTA sites within a short distance of our hotel in Ottawa.
Turns out, there are loads of parks in the Ottawa/Gatineau region so I was spoiled for choice!
Since Ottawa is the capital city of Canada, there’s no shortage of provincial and national parks in the area. (Washington DC is very similar in this regard.)
What, at first, surprised me was the number of parks that had either never been activated or had only been activated a handful of times. Taking a closer look in advance and with the assistance of Google Street View, I could see that many of these entities are simply historic buildings/sites or formal parks in the city with no easy means of activating without special permission.
Hog’s Back Conservation Reserve (VE-1596)
Shortly after noting on QRPer that I’d be in Ottawa a few days, a reader named Andrew reached out and offered advice about local parks. He suggested the Hog’s Back Conservation Reserve since it was only a 15 minute drive from our hotel. We made plans to meet up there for the activation.
If you’ve been following my field reports and activation videos, you’ll note that I’m almost twomonths behind posting them at present.
Much of this is due to the fact that I made numerous activations during a camping trip at New River State Park with my family in April and many more activations during a camping trip with WD8RIF and KD8KNC in West Virginia in May.
May was an extremely busy month for me family-wise and I was fitting in Canadian Basic Exam prep during any free time I had because my goal was to write the Canadian Basic exam within the first few days of arriving in Canada.
Looking at my field report back log, I’ve got a few more reports from both the NC and WV camping trips, but I’ve decided to put them on hold for a bit so that I can post more recent ones. Plus, it might be fun posting late spring field reports this fall!
One of the things I love about writing these field reports is re-living the activation.
Objectif Québec
We began our road trip to Canada on the morning of June 15, 2022.
Our first stop would be Pine Grove, Pennsylvania, the second stop Ottawa, Ontario (for three nights), and then our final destination of St-Ferréol-les-Neiges, Québec. All in all, we’d log 1,306 miles/2,102 km not including side trips.
Although I sort of fantasize about all of the amazing parks I could activate during our travels north, in reality this road trip was all about reaching the destination in fairly short order to save on hotel expenses en route.
The first leg of the trip equated to a good 10 hours on the road including stops to refuel, stretch our legs, and grab a bite to eat.
That first day, I’d completely written off the idea of performing a POTA activation assuming we’d arrive in Pine Grove, PA too late and too tired.
Turns out, though, we got an earlier start than we had anticipated, so arrived in Pine Grove around 16:00 local. That afternoon, everyone was eager to take a stroll or hike to shake off all of those hours of sitting in the car.
I checked my POTA Map and then cross-referenced it with my All Trails app to find the closest park with proper hiking trails. Turns out Swatara State Park met both criteria and was a mere 8 minutes from our hotel. Woo hoo!
Honestly: Swatara couldn’t have been more convenient for us.
To date, I believe I’ve activated 11 parks (1 in Ontario, 10 in Québec) during our extended family vacation. Instead of hitting the same parks over and over, I’m trying to activate new parks during each outing because it’s giving us an opportunity to explore some really amazing spots that we might not otherwise discover.
Camping on the North Coast of the St. Lawrence in Bon Désir.
Before we leave La Belle Province, I’ve at least two SOTA summits in mind and 3-4 more parks, family time permitting. Indeed, as I mention below, I hope to activate another park sometime today.
Ham Radio Workbench Podcast
Once again the fine crew of the Ham Radio Workbench Podcast made the mistake of inviting me on another episode of the podcast.
In truth, it’s a proper honor to join them each time (don’t let them know I said that!). Seriously, they’re an amazing group of friends.
This episode was dedicated to our Field Day activities. For many of us, it was an unconventional Field Day and perhaps that’s what made the event so much fun.
John (W7DBO) was invited back to the show and it was great hearing how he integrated his whole family in his Field Day activities.
George had to operate from home, I operated from our condo/chalet here in Québec, and Vince from his very unique club setup in Alberta. Rob had a project that took priority on Field Day, and it’s worth listening to the podcast just to hear Smitty’s tale of life as a Field Day RVer (hint: not for the faint of heart).
I did finally choose that one extra radio: the Discovery TX-500.
I chose the TX-500 because 1.) it would be a great “bad weather” radio, 2.) it could operate from my KX2 battery packs, 3.) it’s multimode and also covers 6 meters, and 4.) it has such a slim profile. I could easily the TX-500 in my Tom Bihn Synapse 25 backpack with the Elecraft KX2 and it didn’t make the pack feel any bulkier.
I came very close to choosing the IC-705, but it was just a bit too bulky for the way I had my pack configured.
Back to the hypocrite part…
The day before leaving North Carolina, I removed everything from our Subaru and gave it a deep cleaning.
When I pulled up the floor panel in the trunk/boot area to check the first aid kit, spare tire, and emergency gear I discovered that there was a fairly large unused area under there–a spot where I might be able to sneak a few extra radio supplies.
After a little finagling, I discovered that I could fit spare batteries, two folding PowerFilm panels, the Buddipole PowerMini 2, and two more radios: the MTR-3B field kit, and my Elecraft KX1.
This essentially amounted to contraband since I tend to be the guy who enforces “one bag per person” policy during our family travels.
I got some serious eye rolls from the family when they discovered the hidden radios after we reached our destination. I might not ever live this down.
If I had even a shred of dignity upon our arrival here in Canada, I can confirm it’s gone now.
Elecraft KX2 getting heavy use
Other than Field Day where I primarily used the TX-500, the Elecraft KX2 has been getting a heavy workout on this trip.
The reason why is because I’ve been activating a number of urban parks where an all-in one radio paired with a random wire or the AX1 vertical has been very useful.
Conditions have been very rough during some of these activations as well, so it’s nice to have both CW and SSB modes available and a full 5 watts (the KX1 and MTR-3B are CW-only hover around 3 watts). I’ve snagged some excellent QRP DX at times, but everything has been so unstable.
I didn’t bring the KX2 hand mic on this trip, so all of my SSB contacts have utilized the KX2’s built-in mic. It’s actually worked brilliantly!
I’ve recorded a number of activations here in Canada and will likely post a couple of these out of chronological order while I’m still on this side of the border.
Uploading from our chalet hasn’t been possible–the upload speeds are about as dismal as they are at my QTH. Download isn’t too bad, though.
Hôtel Le Manoir, Baie-Comeau
While at the hotel in Baie-Comeau a few days ago, I uploaded at least four videos with their high-speed internet, so I’ll soon post a couple of them.
In short: the activations here have been amazingly fun. Some of the sites have been truly spectacular in terms of scenery and others are in urban settings taking me well outside my comfort zone.
In short: I’ve loved every minute of it!
Travels
Photo by K4TLI
We have had an amazing time here in Québec as always.
Our flavor of travel is the opposite of many: we tend to rent a home or apartment for a few weeks or couple of months and use it as a base for exploring the region. We do this as opposed to traveling long distances and only spending relatively short periods of time at multiple stops.
Activation today
I plan to activate a park while in Québec City today. I’ve no clue which one it’ll be yet, but I’ll announce it on the POTA site once I’ve got a plan together. If you have the time, look for me on the POTA spots page (as VY2SW) or via the RBN! I’d love to put you in the logs.
Here’s wishing all of you a week full of radio and fun!
As you might have guessed, I’m a bit of a QRP radio addict.
Over the years, I’ve owned and sold quite a few rigs; there are some models that gave me instant seller’s remorse.
In the past, I sold good QRP radios to buy “better” ones: transceivers that had a more compact form factor, better feature set, better battery management, or other desirable updates/upgrades.
Boomerang!
In almost every case when I experienced seller’s remorse, that particular model of radio has eventually found its way back into my field kit.
I sold my Elecraft K2/100 to fund the purchase of my Elecraft KXPA100. I don’t regret purchasing the KXPA100 in the slightest (even though I so rarely use it), but I do regret selling not one, but two K2s over the years! I’ll snap one up if I find a good deal.
I also sold my Elecraft K1 to help fund the purchase of my Elecraft KX3 in 2013.
At the time, the seller’s remorse wasn’t immediate because the KX3 was such a revolutionary portable radio in almost every respect. The K1 seemed so limited in comparison.
Still, since I started doing CW POTA and SOTA activations, I’ve been keeping an eye out for a good deal on another 4 band/ATU Elecraft K1.
Why does the K1 have appeal when I have so many “superior” radios at my disposal–?
Good question! I reckon I just like it.
(Image via WD8RIF)
The K1 feels more like an analog radio rather than a digital one; no doubt, this is due to its VFO’s limited range. It’s more akin to an analog radio with a digital frequency display.
The K1 is also super compact for a radio with a traditional tabletop form factor. The menus and features take a bit of time to learn–they’re cleverly implemented, but you definitely need an owner’s manual or cheat sheet to master them.
The K1 is not general coverage; it can only be configured to operate on a maximum of four CW bands. It does have an internal ATU option, but I don’t think it’s on par with the KX-series internal ATUs in terms of matching range. It works well with a variety of field antennas, though!
The K1 does have a very low noise floor and wonderful audio. Those are perhaps the two things I love most about it.
Hawks Nest State Park (K-1813)
During my West Virginia POTA expedition with Eric (WD8RIF), Miles (KD8KNC), and Theo (The “Great Warg”) dog we hit Hawk’s Nest State Park on Friday, May 20, 2022; this was our second park of the day (New River Gorge was our first).
En route to the site, Eric suggested I use his Elecraft K1 travel kit during this activation and I quickly accepted the offer!
I used everything in Eric’s Kit save the antenna.
Photo courtesy of WD8RIF.com
Instead, I paired the K1 with the homemade 40M End-Fed Half-Wave MW0SAW kindly sent me.
I also used a 50′ of feedline so that I could move the antenna as far away as possible from the picnic shelter Eric and I would both be using during the activation.
The long feedline also made it possible to set up the antenna in a way that it wouldn’t interfere with any park guests who might walk by.
The separation/distance from Eric’s Tri-Bander antenna worked a charm: there was very little interference between our two stations.
I started the activation by calling CQ POTA on 20 meters. Funny: I actually thought I was on 40 meters; the K1 display (much like that of the KX1) only shows the last three digits of the frequency display; when I saw “61.1” I assumed “7061.1” but of course it was actually 14061.1. I realized this as I later changed meter bands.
Although the propagation forecast was pretty dismal, the EFHW performed very well.
Within 18 minutes, I logged 16 hunters (including WD8RIF some 20 feet away).
I then moved to the 40 meter band (so Eric could move to 20) and worked an additional six stations in six minutes!
The final contact was both an HF and eyeball QSO with WD8RIF. I got that on video–very much a fun first for me!
QSO Map
Here’s what my five watts into an end-fed half-wave looked like on a QSO Map:
Activation video
Here’s my real-time, real-life video of the entire activation with WD8RIF. I include a bit about Eric’s station and also his QRPguys Tri-Bander antenna after I go QRT. As with all of my videos, there are no ads and I don’t edit out any of the activation:
Make sure to check out Eric’s field report which includes details about his KX3 set-up that you’ll see in the video above.
Thank you!
We spotted this little guy on a hike after completing the Hawks Nest activation.
Thank you for joining me (and Eric, Miles, & Theo) on this POTA activation.
Although detailed field reports take a few hours to write-up and publish (along with activation videos), I truly enjoy the process. It gives me a chance to re-live an activation and share the whole experience with kindred spirits. This was such a fun activation.
Of course, I’d also like to send a special thanks to those of you who have been supporting the site and channel through Patreon and the Coffee Fund. While certainly not a requirement as my content will always be free, I really appreciate the support.
Oh, and if you have a four band Elecraft K1 with ATU you’d like to part with? Get in touch with me! 🙂
We’re in the Baie-Comeau area at present, and I’ll only have a short window to fit in this activation before we hit the road again and do a little off-grid camping for a few days!
I’ll be QRP and hopefully on 20 and 40 meters CW. If I have the time (and mobile coverage to self-spot) I’ll attempt to do a little SSB as well. If I can find an adequate tree (they’re not so tall along this trail) I’ll deploy an EFHW, else it’ll be a random wire.
Conditions have been so rough lately, I’m not quite sure what to expect; especially this early in the morning at this location.
This will likely be my only activation for a few days because there are sadly no POTA/WWFF parks nor SOTA summits within easy reach of our campsite along the St-Lawrence.
Update!
Thanks to everyone who listened for and logged me this morning. The activation was a big success. I logged a total of 30 stations on three modes all in very short order.
Thanks so much! Now it’s time to pack the camping gear and go whale watching!
More specifically, I wanted to activate the park by way of the scenic one-way road that starts near the New River Gorge Visitor’s Center and descends down to the Tunney Hunsaker Bridge (the “old” New River bridge).
Why? Because in December 2016 during the National Parks On The Air (NPOTA) program, I passed through West Virginia and activated some very rare parks on my way to a multi-day park run with Eric in Ohio. I fully intended to activate the New River at this very spot (underneath the “new” New River Bridge) after hearing how amazing the drive was from Eric.
Unfortunately, I happened to time my trip through West Virginia on a day when we received about an inch of snow. Even though (at the time) I was driving a Toyota minivan with nearly bald tires, the snow didn’t pose a problem at any other site, save this one. I had to change my plans and activate the New River in a spot where the access had less elevation change on a narrow snow-covered road. With my Subaru, this wouldn’t have been an obstacle in the slightest.
I was looking forward to going back to this site and was very pleased to see that Eric and his son, Miles, had already planned this trip in the draft itinerary!
New River Gorge National Park (K-0696)
On the morning of May 20, 2022, Eric, Miles, Theo the dog, and I left our campsite at Babcock State Forest and made our way to the New River Gorge Visitor’s center next to the New River Bridge.
If you’re ever in this area, I’d highly recommend checking out this visitor’s center as it has some well-designed exhibits detailing the impressive engineering that went into the construction of the New River Gorge Bridge.
There are also some fantastic views from the visitor’s center and from its short gorge overlook trail.
From the trail overlook at the visitor’s center we could see the spot where we planned to activate near the Tunney Hunsaker Bridge deep in the gorge (see photo above).
The drive into the gorge was quite scenic with a number of spots to park and take in the enormity of the New River bridge.At the bottom of the gorge, the view was pretty spectacular as well!
My partners in crime: Eric, Miles and “The Great Warg” (Theo the dog)
Tufteln 9:1 EFRW (End-Fed Random Wire) antenna
I mentioned in a previous post that long-time QRPer.com reader and supporter, Joshua (KO4AWH), runs an Etsy store with a wide range of products primarily designed for field operators.
Besides the Elecraft T1 protection case I mentioned previously, he also sent a couple of his QRP field antennas for testing and evaluation (to be clear: free of charge). Thanks, Joshua!
This year, instead of attending the 2022 Hamvention, my buddy Eric (WD8RIF) and I hatched another plan.
Eric and I–along with his son Miles (KD8KNC) and sometimes Mike (K8RAT)–attend Hamvention every year it’s held. We’d planned to do the same this year especially with it being the first in-person Hamvention since 2019.
As Hamvention approached though, we both had a lot going on in our lives and decided to save a little money, a lot of travel time, and meet in West Virginia for several days of POTA activations and just hanging out. I explain a bit more about the decision in this previous post.
On the afternoon of Thursday, May 19, 2022, we (Eric, Miles, Theo the dog, and I) met at Babcock State Park and set up our tents at the adjoining campsites we’d reserved.
Babcock would serve as our home base for the entire WV POTA expedition.
As a bonus, Babcock State Park (K-1798) is also a POTA entity, so we activated it in the late shift after dinner each evening.
As soon as the tents were deployed that afternoon, we all jumped into Mile’s Subaru with our radio gear and hit our first park!
Beury Mountain Wildlife Management Area (K-7036)
Beury Mountain WMA is so close to Babcock State Park, I have to assume they share a common boundary.
Looking back at last year (2021), if I had to pick out one of the easiest SOTA activations I made, Mount Jefferson would be near the top of the list. It’s a very accessible summit although not technically a “drive-up” summit because you will need to walk a short distance up a service road to the activation zone (AZ).
Mount Jefferson (W4C/EM-021) is located on and protected by the Mount Jefferson State Natural Area (K-3846), so when you activate Mount Jefferson for Summits On The Air, you can also claim the activation for Parks On The Air and World-Wide Flora and Fauna as long as you work at least 10 contacts.
What I love about POTA and SOTA “2-fer” sites like this is that you can set things up to be spotted in both systems (and often the WWFF system, too!) which increases your audience of hunters and chasers, thus increasing your odds of achieving a valid activation in all programs. It’s especially desirable if you’re a CW op and know you may potentially be in a spot with no mobile phone service for self-spotting; if, for some reason, RBN auto-spotting functionality is down with one program, the other serves as a backup.
Mount Jefferson is at least a two hour drive from my QTH, but it was easy pickings on April 29, 2022 because it happened to be within spitting distance of New River State Park where I was camping with my family.
Mount Jefferson (W4C/EM-021)
The drive to Mount Jefferson took all of 20 minutes which was a good thing because our family had other activities in store that day including some extended hikes!
As soon as we drove up to the activation site I had researched in advance, I surveyed the picnic area and mentally noted the best spot to deploy an end-fed half-wave using my trusty arborist throw line.
With the throw line’s assistance, I had an antenna deployed within a couple of minutes max.
It hit me then just how invaluable a tool the arborist throw line has become for the types of park and summit activations I do.
Pre-Throw Line Activations
During NPOTA (National Parks On The Air) in 2016, I wasn’t aware of arborist throw lines and had been using some high test monofilament fishing line attached to a weight.
The fishing line was strong enough to support my QRP antennas and I could typically reuse the same length of line for 2-3 activations. Eventually, the line stretches and weakens thus it must be cut off and discarded.
Never again
I’m a big Leave No Trace kind of guy, so am embarrassed to admit that during one activation, my fishing line snagged high up in a tree and left a bundle of broken monofilament in a spot where I could not retrieve it. This was deep in a forest and although I doubt anyone will ever see it, I know it’s there. It bugs me to this day and if I ever sort out a way to remove it, I certainly will.
I was searching for a more SOTA-friendly/backpack-able solution than the arborist throw line cube.
I was very skeptical about how easily this bag would work in the field. One of the reasons my throw line storage cube works so well is because the opening is large allowing the line to deploy without tangling. Packing up is fast because the line can be flaked back into the cube in a matter of seconds. Continue reading The arborist throw line is an invaluable field radio kit tool→
QRP radios, product announcements, reviews, news and more. Low power amateur radio fun!
Please support QRPer by adding us to your whitelist in your ad blocker. Ads are what helps us stay online. All of our ads are ham radio related--no junk, we promise! Thank you!
Sometimes, I like going a little stealth.
