Category Archives: POTA

QRP POTA from 10 to 20 Meters with the Chameleon Tactical Delta Loop and Icom IC-705

I do my best to shake up each field activation I perform. Even if in some small way.

While it would be way more efficient to deploy the same radio and antenna combination at each park and summit I visit, I get a thrill out of trying different radio and antenna combinations.

I should add that I’m fully aware how fortunate I am to have a lot of radios and even more antennas to pair in various combinations. I keep reminding myself that building and buying radios and antennas is still cheaper than restoring a 1940s era Willys CJ-2A.

Recently, a reader reached out and asked my opinion about the Chameleon Tactical Delta Loop (CHA TDL) antenna. I think the TDL is a brilliant antenna system, actually, and the one I recommend the most from Chameleon because of its versatility.

Not only can it be deployed as a multi-band vertical delta loop but it has all of the parts needed to be an MPAS Lite vertical as well, save the counterpoise.

The CHA TDL comes with a 25 foot wire that connects the two 17′ whips into a loop configuration, but the clamps on the end of that wire can’t connect to the ground lug on the MPAS ground spike terminal as-is. That said, you could easily make a short connector cable or connection point that would allow the CHA TDL wire to clamp to the ground spike terminal. Else, of course, you could cut a dedicated 25′ counterpoise from pretty much any wire you might have around the shack.

You can buy the same counterpoise used with the MPAS Lite package, but it’s more affordable just to build your own since there’s no magic in the counterpoise. And, FYI, configured as the delta loop, there’s no need for a separate counterpoise; only if you configure it as a vertical.

This same reader also has an Icom IC-705 and an mAT-705 Plus antenna tuner. He was curious how well that combo might work with the CHA TDL. I knew that the combo would work well, but I thought, “why not try it?”

I realized that it has been ages since I last deployed the CHA TDL in the field.

Zebulon B. Vance Birthplace (K-6856)

Tuesday, February 28, 2023, was a gorgeous day weather-wise, although it was a bit gusty at times.

I arrived at K-6856 and decided to film the full set-up of the CHA-TDL.

For an antenna with a fairly large profile when deployed, it’s actually very compact, albeit a bit heavy (mainly due to the weight of the solid stainless ground spike and TDL hub). That said, I did take this same CHA TDL setup on an 11 mile round-trip SOTA hike once and didn’t find it too heavy.

I placed my Icom IC-705 on the table in the picnic shelter and connected the mAT-705 to it with a 2′ BNC-BCN RG-316 cable and the ATU control cable. Continue reading QRP POTA from 10 to 20 Meters with the Chameleon Tactical Delta Loop and Icom IC-705

A story about a gluttonous dragon, a princess, a knight, and many DX contacts to the US from a volcano in Germany

by Thomas (DM1TBE)

Intro

If you have read my previous activation reports, you may remember that the temperature was more often than not below 0° C / 32° F. I am tired of the winter. So I was very pleased when the weather forecast indicated 18° C / 64° F on a Saturday.

In one of my previous posts (How I found the best antenna for my SOTA/POTA activations) I have outlined, that I like using the 30-meter band for being reliable on short and medium distances – in my case, Central Europe. However, I wanted to try an activation with an antenna that is more appropriate for DX. The wire winder for my 30-meter antenna had plenty of space left, so I decided using a commercial 12/17-meter band wire antenna that I have discussed briefly in the report linked at the beginning of this paragraph.

The day before, I built a 20-meter end-fed with parts that I found in my basement and a tiny 1:49 transformer from K6ARK. I added a short coil, so the feed point wouldn’t be at or too close to the ground when using my 10 m / 33 ft fiberglass mast. I know it needs some polish.

The Limburg

The Limburg is a conical summit about a 30-minutes drive from my home. It can be activated for a couple of programs like SOTA (DM/BW-110), POTA (DA-0203), WWFF and COTA.

The Limburg is, or better was, a volcano; technically, a volcanic vent of the Swabian Volcano, a volcanic area of 50 km / 31 mi radius with over 350 volcano vents. Seventeen million years ago, it produced massive gas and dust explosions. Be careful when ramming your antenna groundspike into the ground ;-). So it became a steep summit, elevated around 200 m / 650 ft over its surrounding area.

Earliest traces of population around the summit date to 3000–1800 BC.

Around the year 1050 Duke Berthold I., picture below, built one of the oldest Romanesque castles on the top of the summit. It was the seat of the House of Zähringen, who were related to the House of Hohenstaufen, about whom I wrote in an activation report here earlier: DM1TBE Field Report: Shivering with 18 WPM on the ruins of the medieval Hohenstaufen Castle

Around 50 years later, his son Berthold II. built a new castle some 150 km / 90 mi away and moved the seat of the family. Shortly thereafter, the castle was destroyed (probably, nobody knows exactly). It was rebuilt and destroyed again in 1130 and rebuild again. After the year 1150 a new, larger castle was built not too far away and this castle lost its importance and, eventually, gave up. Continue reading A story about a gluttonous dragon, a princess, a knight, and many DX contacts to the US from a volcano in Germany

Huge 30 Meter Pileups: Beautiful day for a SOTA & POTA Activation at Hanging Rock State Park

There are a few reasons I love Summits On The Air (SOTA):

  1. I love hiking.
  2. I love going truly portable with my radio gear; packing an entire minimalist station in my backpack along with first aid supplies, water, and a bite to eat, then hitting the trail.
  3. I love the views.
  4. I love the sense of accomplishment (hiking to a summit doesn’t happen every day).
  5. I also love that post-hike feeling–my body telling me, “Hey, T, thanks for doing something today!

No kidding: If I could, I would do a SOTA activation at least twice a week. Maybe when I retire, I will.

Living in the mountains of western North Carolina, I have no shortage of summits to activate–indeed, one is within (strenuous) hiking distance of my QTH.

So why don’t I activate more summits?

It’s because they are much more difficult to fit in my active schedule.

You’ll notice that the bulk of my POTA activations take place within a one hour window of time. This includes set-up, on-the-air, and pack-up time. The brilliant thing about POTA sites is that they’re so accessible in my weekly travels. (Plus, I absolutely love POTA too!)

My average SOTA activation, on the other hand, requires at least a three hour window of time. In fact, it’s usually much closer to four or five hours.

The view from Dogback

Drive-up summits like Anderson Mountain and Dogback Mountain are the exceptions. There’s no hiking time involved, so they are pretty easy to fit into my schedule.

On Saturday, February 18, 2023, a rare thing happened: an entire day opened up for me to play radio. The only real obligation I had was to set-up and participate in a live stream with Josh (KI6NAZ) on the HRCC channel that evening.

At first, I thought about doing a five park POTA rove, hitting four parks and one game land all that eight hour window of time. It was very doable and I knew it would be fun.

But then again, park roves allow very little time for hiking–typically, they’re wham-bam style short activations.  It was also a gorgeous day weather-wise so I scrapped the idea of a POTA rove. (This time!)

Instead, I had a hankering to do a SOTA activation and hike. I took a quick look at SOTL.as and remembered how much I enjoyed my last activation of W4C/EP-001 (Moore’s Knob) at Hanging Rock State Park (K-2753). And hey! It’s both a SOTA and POTA site!

It’s been nearly two years since I’d visited Hanging Rock SP because it’s a two hour drive in a direction I rarely travel.

Hanging Rock  a beautiful park and I truly enjoyed the hike to Moore’s Knob.

As a bonus, Hanging Rock State Park is less than a 30 minute drive to Pilot Mountain State Park. I knew I’d have time in the schedule to do activate both sites! Score!

Hanging Rock State Park (K-2753)

I pulled into Hanging Rock that morning and made my way to the parking area by the lake.

Since it had been nearly two years, I consulted the hiking trail map at the trail head to confirm I was taking the correct loop (Moore’s Wall Loop). Continue reading Huge 30 Meter Pileups: Beautiful day for a SOTA & POTA Activation at Hanging Rock State Park

A Casual 17 Meter POTA Activation with the Penntek TR-45L, PackTenna Random Wire, and a Furry Friend

On Sunday, February 19, 2023, I felt like I was moving in slow motion.

The previous day started early and I fit in a long hike, a SOTA/POTA activation, and a second park activation. Round trip driving time was about four hours, but it was worth it. I had an amazing time. Those field reports will be posted in the upcoming week.

The previous evening, I also participated in a live stream and after hours chat with Josh (KI6NAZ) on his amazing Ham Radio Crash Course channel. It was loads of fun, but I was up pretty late after a long day.

Sunday morning, I was feeling it and couldn’t decide if I wanted to do a POTA activation on the drive back to the QTH. In case I decided to, early that morning, I scheduled an activation at Table Rock Fish Hatchery with a very wide activation window. I often don’t have enough mobile phone service to self-spot at that particular site, so I decided that if I was able to make the activation, it would cover me.

I wasn’t even ten minutes into the drive home when I decided to go for the Table Rock activation, of course! I seem to never be too tired for some POTA!

I did make up my mind in advance to try to activate the park on 17 meters because 1.) there was a CW contest that weekend, and 2.) I wanted a more laid-back activation instead of a pileup. I figured 17 meters would have some activity, but not to the degree of the non-WARC bands.

Table Rock State Fish Hatchery (K-8012)

I decided to record the entire activation from set-up to pack-up so I grabbed the action camera from my radio bag in the passenger’s seat and started recording as I pulled into the site.

I had a lot of gear in the trunk/boot of my car–more than normal–because I brought along quite a few radio packs to show on the HRCC live stream for this trip.

I grabbed the Penntek TR-45L and PackTenna random wire.  I thought they would pair nicely for a casual POTA activation.

Set up

The great thing about the PackTenna random wire antenna is that the radiator is only 31′ long. It’s super easy to deploy. Continue reading A Casual 17 Meter POTA Activation with the Penntek TR-45L, PackTenna Random Wire, and a Furry Friend

“Return-to-Office Policy” triggered POTA activation

“Return-to-Office Policy” triggered POTA activation

by Thomas (DM1TBE)

I wasn’t sure if I should write a report about this activation. It was “average” at best. But I thought it might be worth to share that not all activations are perfect, with stunning views in an enjoyable environment.

Intro

I am a relatively new ham and completed my first exam in mid-2019. It took me a while to get my head around all the things that the new hobby is offering. My first successful portable activation was in May 2021 on the SOTA summit Michelsberg (DM/BW-855) – here is a picture of my most recent activation some weeks ago:

This first activation was in the middle of the Corona pandemic. The good thing during the Corona time was certainly the possibility to work from home. Before Corona, I did commute roughly 65 km / 40 mi (oneway), which took me in total 2–3 hours daily. During the first two years, I was in the office two times. In the third year, I was there more often, maybe once every two months.

Two weeks ago, my employer announced a “return-to-office” policy, so the “sweet life” was coming to an end.

After the first disappointment, I thought that this may offer me the chance to work portable at new locations. The next SOTA summit is around 20 km / 12 mi away, but a POTA park begins 2 km / 1.2 mi from the office at the pin in the map below. The park is basically all the green wood in the center of the map.

That comes in very handy, as POTA, with the possibility to operate next to my car, does make it easier than hiking in suit and tie to a SOTA summit.

The Nature Park Schönbuch, POTA DA-0008, located southwest of Stuttgart, is a wooded area of 156 km² / 38,000 acres. In 1972 in became the first nature park of the federal State of Baden-Wuerttemberg. The park is an important recreational area for the region.

Image by Cactus26 – Wikimedia Commons – CC BY-SA 3.0

Activation

Right at the beginning of the park, when coming from my office, there is a parking place and next to it a clearing with a fireplace. I thought that this would be a perfect spot for my activities. Weather was cold and windy on my first “return to office” day, I did not expect too many people to be there.

After working and reading the article about the 2023 QSO Today Virtual Ham Expo, I decided to leave the office early at around 4pm and started my activation.

The parking place at the park was pretty empty, just one old car with four lads in it and doing whatever lads are doing in the woods. I have a 16-year-old son and have given up trying to understand what boys at that age are doing.

The spot was OK, but not as perfect as I had thought. It was in a trough surrounded by large trees. In addition, it was wet, cold and windy.

Due to the wind, I have decided against the 10 meter / 33 ft pole and used the PAC-12 again.

The actual activation did not go as smoothly as my previous one. It might have been due to the time, and afternoon during the week, or the topographical conditions. With a small foldable seat and a tiny desk made of a trunk and a brick, I operated for 40 minutes.

In total, I made 16 QSOs; 10 on the 30-meter band and 6 QSOs on 20 meters.

Although I made a successful activation of the Nature Park Schoenbuch, DA-0008, I think I need to change my plans. Being in the office and therefore close to this park more often in the future, I will be more picky in terms of weather and location. The park has way more to offer than a wet and cold meadow in the middle of the woods. I will look for better weather and locations, such as the following – I just need to find those places.

Image by Martin Rathgeber – Wikimedia Commons  – CC BY 2.5

Postcard Field Report: Cheap POTA thrills with the TEN-TEC R4020 and Chelegance MC-750

Welcome to another Postcard Field Report!

My Postcard Field Reports are information-packed, just slightly more concise and distilled than my average field report so that I can publish them on a busy day.

T-T R4020

One of the least expensive radios I’ve ever purchased is my TEN-TEC R42020 two-band CW only radio. I believe I paid $120 for it (shipped!) a couple years ago and it sat on my shelf unnoticed for months until I took it on a POTA activation last year.

Here’s the admission:  I really love this little radio!

It is not a feature-rich radio, and the sidetone sounds like a 1080s handheld arcade game, but it works a charm! The receiver and audio are fantastic and it sports two of my most useful POTA/SOTA bands: 40 and 20 meters.

What’s not to love?

POTA time!

I had an early morning doctor’s appointment on Thursday, February 23, 2023. As a little reward  for doing my annual physical I decided to add a POTA activation to my morning. This was a last minute decision, so only a couple minutes before leaving the house that morning, I grabbed my TEN-TEC R4020, the Chelegance MC-750, and my Spec Ops Backpack (filled with all other field accessories), and I hit the road!

I chose the MC-750 that day because I needed an antenna that could be configured to be resonant on 40 meters since the R4020 has no internal ATU. That and I couldn’t remember if I’ve configured the MC-750 for 40 meters in the past. I know I’ve deployed the MC-750 with the 40M coil, but I think I may have used an ATU to match it.

I arrived at the Blue Ridge Parkway (K-3378 NC) mid-morning and set up in very short order. Continue reading Postcard Field Report: Cheap POTA thrills with the TEN-TEC R4020 and Chelegance MC-750

QRPer Notes: 3Y0J Presentation, BitBanger Demo, POTA Developers Live, and Georgia State Parks On The Air Event!

Because I receive so many tips from readers here on QRPer, I wanted way to share them in a concise newsletter format.  To that end, welcome to QRPer Notes, a collection of links to interesting stories and tips making waves in the world of radio!


Adrian Ciuperca (KO8SCA):  3Y0J Presentation to the Northern Illinois DX Association

Many thanks to Eric (WD8RIF) who shares this excellent presentation by Bouvet activator, Adrian (KO8SCA):

 Click here to view on YouTube.


BitBanger Demo

Many thanks to Benn (AK4AV) for sharing this video demo:

Click here to view on YouTube.

Click here for the Github page and more notes/details.

Ask the POTA Developers – LIVE!

Click here to view the archived live stream on YouTube.


Georgia State Parks On The Air: April 1-2, 2023

Many thanks to Scott Wooten who shares the following announcement via YouTube:

Welcome to the Georgia State Parks on the Air event. Our goal is to have all fifty Georgia State Parks on the air in one weekend. This event is open to all licensed Amateur Radio Operators whether you live in Georgia or not.

There are two ways to participate: Activating or Hunting. Activators fall into two different categories: Single Operator or Club, and there is a special category for Georgia ARES operations.

The first annual 36 hour event kicks off on April 1, 2023 at 1200 Zulu and concludes at 2359 Zulu on April 2, 2023.

If you participate please remember this event is considered a CONTEST, so while casually operating Parks on the Air on the WARC bands is permissible, this event does not allow operations on the WARC bands.

For more information or to sign up as an activator, go to GAPARKS.org

We look forward to hearing you on the air!

Click here to view on YouTube.

Breaking in the new Elecraft AX2 during a short POTA activation

As I mentioned in my recent AX1 vs AX2 video and blog post, I purchased an Elecraft AX2 antenna and bi-pod in late January (note: two days before Elecraft announced their February ’23 sale price! Doh!).

I received the AX2 package a few days later and I was certainly eager to take it to the field.

My first opportunity came on Tuesday, February 14, 2023, when a short activation window opened up in the afternoon.

Zebulon B. Vance Birthplace (K-6856)

One of the first things I noticed after taking the AX2 out of the package is just how solid and compact it is. The AX1 is short, but the AX2 is a few inches shorter because the base is more compact.

Unlike the AX1, the AX2 is a mono band antenna, thus the coil only needs to accommodate one band. When you receive a new AX2, it’s configured for 20 meters out of the box, but the user can modify the coil to work anything from 20 to 6 meters.

“Resonant-ish”

Even though I mentioned this in my AX1 v AX2 article and video, I’d like to reiterate that the AX2 is nearly-resonant on 20 meters. It is not reliably resonant.

I’ve still been receiving a lot of messages from readers stating that their AX2 and AX1 are resonant on 20 meters, so they don’t pack any sort of matching device in their field kit. They simply hook the AX2 up to their little QRP radio and hop on the air.

While it’s true that these antennas may provide an acceptable SWR most of the time, you really can’t rely on a solid, reliable match as you could with an end-fed half-wave.

I’ll repeat what I mention in a previous post:

Small verticals like the AX1 and AX2, that use coils to electrically “lengthen” the antenna, have a higher Q than, say, a large aperture quarter or half wave antenna. In practical terms, this means that the window of resonance is narrow and more fickle than, for example, an end-fed half-wave.

A lot of factors can affect the SWR on higher-Q antennas like the AX1/AX2 including:

      • the type of terrain,
      • height off the ground,
      • length of counterpoise,
      • configuration of counterpoise,
      • and, most notably, the operator’s own body capacitance.

You may find that the AX2, for example, is natively resonant on 20 meters at one location, but isn’t at another location. This is quite normal. It’s also the reason why Elecraft states that both antennas are designed to be used with an ATU.

So there you go! If I hook up my AX1 or AX2 to a radio, I’ll always have some means of matching the impedance–either an external ATU, or a capacity hat. You can also tinker with the length of the telescoping whip and counterpoise to tweak the match.

The important part–especially if pairing these antennas with a radio that lacks both an internal ATU and SWR meter (say, the MTR-3B, G106, or TR-35)–is that you’ve some means to check the SWR before conducting a long activation session. Continue reading Breaking in the new Elecraft AX2 during a short POTA activation

How I found the best antenna for my SOTA/POTA activations

How I found the best antenna for my SOTA/POTA activations

by Thomas (DM1TBE)

Intro

Until January this year I had a German “Klasse E” / CEPT-novice amateur radio license (equivalent to the US General Class), which limits the use of HF to the 10-,15-, 80- and 160-meter bands. When I started with SOTA I used homemade single band end-fed antennas most of the time. However, that is only feasible for the 10- and 15-meter bands.

Unfortunately, both bands are very moody and sometimes they have not worked at all. Unlike the UK for example, FM is uncommon for SOTA in my home association DM (i.e. Germany Low Mountains). You can be lucky and get your 4 QSOs, but I did not want to rely on pure luck.

Therefore, I bought an end-fed half-wave antenna for 10-, 15-, 20-, 40- and 80-meter bands, after some experiments with 10-80-meter end-fed half-wave antennas, from a small German company called ANjo.

Although I could not use the 20- and 40- meter bands at that time, the EFW80-10P (en: auto-translated) antenna gave me the possibility to use the 80-meter band. The antenna could also be tuned for 15. It has a mechanical length of 23.6 m / 77 ft and a coil for the 80-meter band. It is pretty lightweight with 0.4 kg / 14 oz and allows up to 30 watts PEP – more than enough for me. 80-meters is not the best band for daytime SOTA activations, but in 21 months doing SOTA activations, it worked 37 times and tipped the scales for an activation from time to time.

It was sometimes a bit tricky to raise the long wire into the air, but it always worked … better or worse …somehow … like here in the woods along a trail.

In January this year, I upgraded my license and a new world of HF-bands opened for me. Although I have learned a lot about propagation for the exam, I am in favour of a German saying: “The difference between theory and praxis is larger in the praxis than in the theory”. Continue reading How I found the best antenna for my SOTA/POTA activations

Field Report: More Xiegu G106 POTA time and I rope in Brooks to log!

On Friday, February 10, 2023, I had a hankering to fit in a POTA activation that morning. South Mountains State Park was an easy detour on my drive back to the QTH, so I scheduled an activation.

I’d also been meaning to meet up with Brooks (KO4QCC). Brooks started his POTA journey not even one year ago–here’s a field report from his first SSB POTA activation.

Brooks has been steadily working on his CW skills and is dangerously close to doing his first CW activation. We’ve managed to set up one late evening casual CW rag chew and I think his CW chops are very good.  We plan to do more evening rag chews when our schedules align. He’s made amazing progress.

I contacted Brooks that Friday morning and he was game to meet up and do some POTA. He wasn’t quite ready to do a CW activation, so I suggested he log for me using the HAMRS app on my iPhone. I find that logging for CW ops during past Field Days really helped build my own confidence before I started using CW daily.

Brooks was 100% game to log for me.

And let me just say what a luxury it is to have someone log to HAMRS for me on my iPhone! It frees up my brain to simply log on paper (which I always do) and enjoy working stations without the extra busy work! Hat tip to good ole’ Brooks.

South Mountains State Park (K-2753)

I arrived at South Mountains State Park (the Clear Creek Access), put on my hiking boots, then Brooks pulled into the parking lot only a few minutes later.

We agreed in advance to fit in a quick hike up the Clear Creek Trail prior to the activation. I, for one, really needed to stretch my legs!

After the hike, I grabbed some gear from the car and we set up at the one picnic table at the Clear Creek Access.

Brooks and I both had commitments that day so could only play radio for 45-60 minutes max including set-up and take-down.

I deployed the same antenna I’d used the previous day: MW0SAW’s homebrew EFHW on a SOTAbeams winder.

Deployment didn’t take long–since the 40M EFHW is resonant on both 20 and 40 meters, there was no need for an external ATU. I powered the G106 with a 3Ah LiFePo4 battery via my Ham Radio Workbench DC Distribution Panel. Continue reading Field Report: More Xiegu G106 POTA time and I rope in Brooks to log!