You might recall that my friends Eric (WD8RIF), Miles (KD8KNC), Brian (K3ES), Kyle (AA0Z), Charlie (NJ7V), and Joshua (N5FY) all played hooky on the final day of the 2024 Hamvention (Sunday, May 19) and instead activated a couple of POTA sites.
Our next stop was Whitewater Canal State Historic Site in Metamora, Indiana, about an hour’s drive from the first park.
Only four of us continued to the next park; Kyle and Charlie needed to head to the airport, and Joshua needed to start his drive back to Georgia.
Whitewater Canal State Historic Site (US-6977)
I was excited about visiting Whitewater Canal because it would be my first official POTA activation in Indiana.
We arrived around 1:00 PM and opted to grab lunch at a nearby pizzeria before activating.
Around 2:00 PM, we grabbed our gear from the car and walked across the road to the park grounds.
The Whitewater Canal State Historic Site offers a glimpse into the 19th-century canal era.
Built between 1836 and 1847, the Whitewater Canal was a 76-mile waterway that connected the Ohio River to Hagerstown, facilitating the transport of goods and agricultural products.
This engineering feat played a vital role in the economic development of the region, contributing to the growth of towns and industries along its path.
Today, the preserved section of the canal, along with the historic grist mill and other structures, stands as a testament to Indiana’s rich industrial and transportation heritage.
I’ve always been fond of railroads and canals, so this site was brilliant as it featured both running parallel to each other!
Eric, Brian, and I (Miles didn’t activate) were careful to set up within the actual park boundaries.
In this case, it was a little difficult to determine the exact boundaries because the town and park blend together.
I used the Parceled app on my phone to confirm our location.
Eric set up his Elecraft KH1 station at a picnic table under a large tree.
Brian set up his KX2 on a covered bench next to Eric, using his Elecraft AX1 antenna mounted on a clamp secured to the bench.
Brian’s site was super stealthy behind the sign–since he operated with earphones, you couldn’t hear him and barely could see him!
Can you spot K3ES in this photo?
I wanted to put some space between my station and theirs, so I set up under the shade of a tree (it was blazing hot that Sunday) and deployed my Helinox camping chair.
Local ducks enjoying the shade–I picked a different tree.
I then deployed my Chelegance MC-750 vertical for 20-meter operation since Brian and Eric were on other bands.
Reed Bingham State Park, located in southwest Georgia, is named after Amos Reed Bingham, who envisioned a dam on the Little River to provide electricity to the rural community. Even though the flow of the river was not sufficient for that purpose, Colquit and Cook counties purchased 1,600 acres along the Little River and deeded the land to the state of Georgia, creating the park. A 400-acre lake was created in 1970 by the current dam and provides recreational opportunities for park visitors.
source: Google mapsThe lake at Reed Bingham State ParkOverflow from the dam into the Little River
Besides working toward my 60 new-to-me park activation goal, the trip to Reed Bingham served another purpose – refining my camping set-up and routines before my twelve-day POTA trip this summer. I made quite a few notes about equipment that would make camping life better and realized I need to think through where to keep certain items so I can lay my hands on them more easily and quickly.
The tent at the campsite
A new item I purchased for hiking and camping trips is a hitching system for Daisy. I want her to be able to “free range” while I set up camp, make meals, or visit the bathhouse but still be contained. Ruffwear makes a hitch system with a daisy-chain (aptly named, don’t you think?) on one end and a kermantle rope on the other.
I ran the daisy-chain around a large pine and then, as there was not another tree close enough, the kermantle rope to the rails on the top of Kai. A large carabiner slides up and down the rope and Daisy’s six-foot leash attaches it to a clip on the back of her new harness. The system worked well and eliminated her getting tangled in a lead line while in camp.
After setting up camp and eating supper, it was time to fit in an activation. There were two trees near the campsite – a large oak and shorter-than-usual pine tree. I opted for the pine tree as it was closer to my tent. (I longed to sit in the comfort of my tent on my Thermarest chair for the activation.) Continue reading Overnight at Reed Bingham State Park for the POTA Babe→
On the morning of Wednesday, May 15, 2024, I woke up, grabbed breakfast, and headed to Strouds Run State Park in Athens, Ohio. (You can read about that activation in my previous field report.)
Once I returned to Eric’s (WD8RIF) QTH, Eric, his son Miles (KD8KNC), and I packed up the car for the drive to Dayton—roughly 2.5 hours from Athens. En route, we decided on an activation of Scioto Trail State Park (US-1990) which also happens to be a two-fer with Scioto Trail State Forest (US-5448).
I’d hoped band conditions would remain as favorable as they were in the morning, but the sun had other plans! (Indeed, this would become a recurring theme throughout the following week.)
Scioto Trail State Park (US-1990) and Forest (US-5448)
We arrived at Scioto Trail around 2:00 PM, under scattered clouds and after passing through some rain. We hoped the weather would hold!
I’d never been to Scioto before and was pleased to see a small island on the lake accessible by a footbridge. It had a gazebo, perfect for a POTA station.
Reunited
A highlight of this trip was giving Eric a chance to operate my Index Labs QRP Plus. Eric had owned one for 13 years as his first field radio. In fact, as I’ve mentioned before, when I first met Eric in 1997, it was while he was operating a QRP Plus during FYBO!
Since the QRP Plus is better suited for tabletop use, I recommended Eric set up in the gazebo.
I provided my Chelegance MC-750 for him to operate on 20M.
POTA in the Shade
I set up under a tree at the edge of the island—as far from Eric as possible to minimize interference. In reality, the island is small, so I was only about 15 meters away—not ideal!
The tree offered some shade and potential rain protection. I deployed my Helinox Chair, my “no-transformer, no feedline” Tufteln random wire antenna, the Elecraft KX2, and my Tufteln/N0RNM kneeboard.
When I turned on the radio, I could hear Eric’s signal bleeding through on 30 meters (a band I chose to avoid harmonic interference with 20M).
The KX2 is sensitive, so this wasn’t unexpected. Eric never experienced interference from my station, likely due to the QRP Plus’s less sensitive receiver.
Gear:
Note: All Amazon, CW Morse, ABR, Chelegance, eBay, and Radioddity links are affiliate links that support QRPer.com at no cost to you.
It is summer break and I’m getting stir crazy. Earlier this year, I scheduled an overnight trip to Reed Bingham State Park. However, given the chaos of my personal life, it was necessary to reschedule the trip. The earliest weekend available was Sunday, June 2nd. My son would be out of school for summer break and riding lessons would move to weekdays.
Sunday rolled around and this POTA Babe was ready to hit the road again. Out came the camping gear with a few tweaks. I ditched the DEET insect repellant replacing it with a 20% picaridin spray and added a Thermacell unit. I purchased a hitch system for Daisy as well as a harness to replace her collar. The North Face sleeping bag would stay home and, in its place, I’d use a Sea-to-Summit bag liner for the warmer night temperatures.
Gear – camping, ham radio, videoFood for the trip
With my gear loaded, Daisy and I hit the road a little after 8 AM. Before arriving at Reed Bingham State Park, I planned an activation at Bullard Creek Wildlife Management Area (US-3737). (Yes, I should just become the poster child for wildlife management areas as they’ve become my favorite place to activate in Georgia!)
The drive through rural Georgia was a pleasant one.
source: Google Maps
We passed through towns familiar to us (Pembroke, Claxton – the fruitcake capital of the world, and Reidsville) as well as new places like Daisy, Georgia. It was a pleasant trip and before I knew it, there we were, crossing the Altamaha River a stone’s throw from Bullard Creek Wildlife Management Area (WMA).
Actually, Apple Maps routed me to Bullard Creek itself and not the WMA. After a little sleuthing, we were headed in the correct direction and accessed the WMA via a back route. (I knew we were in the right place when I began seeing WMA boundary signs!)
Bullard Creek WMA consists of over 17,000 acres in two tracts along the Altamaha River. One can hunt as well as fish, view wildlife, and use the public shooting range. This WMA was among one of the nicer properties I visited so far.
Shooting range on site
Not far after entering the WMA, I found a clearing off the main road and decided to set up there. Present in the clearing were pine trees with branches low enough to reach with my arbor line. (I knew the WMAs allow wire antennas and figured Reed Bingham would as well so I left the Chelegance MC-750 at home.)
After donning my blaze orange vest and hat, I had the Tufteln EFRW in the tree, the coax attached, and was settled to begin.
The road beyond our clearing for the activationPines with lower branchesDaisy’s checks out the surrounding woods
Two things happened in short order. (Remember, ALWAYS expect the unexpected with POTA.) I couldn’t access the POTA site to spot myself due to variable cell service. My partner Glenn W4YES came to the rescue and spotted me on 30 meters. I worked a few callers and then…the sun came out. Literally. Continue reading The POTA Babe Embarks on an Overnighter→
On Tuesday morning, May 14, 2024, I hopped in my car and headed north to Athens, Ohio. It was in Athens, back in 1997, that my ham radio journey truly began, and where I met my friends Eric (WD8RIF) and Mike (K8RAT).
For over 14 years, Eric, his son Miles (KD8KNC), and I have made the annual pilgrimage to Hamvention and FDIM, with few interruptions. My routine is to drive to Athens, catch up with Eric and his wife, Vickie, stay overnight, and then head to Dayton the next day with Eric and Miles. I enjoy this because it breaks up my travels and usually allows for some POTA activating along the way.
This Wednesday morning, Eric had an appointment and a meeting, so our plan was to leave for Dayton around noon. This gave me the morning free to play radio!
Breakfast at Miller’s Chicken
I left the house around 8:00 AM with the goal of activating Strouds Run State Park, conveniently located near downtown Athens. But first, breakfast!
I try to avoid chain restaurants when traveling, preferring local spots. I was delighted to discover that Miller’s Chicken, an Athens institution, served breakfast. I had no idea!
Miller’s Chicken holds fond memories for me. When my wife was a graduate student at Ohio University, for a brief period of time, she lived within walking distance and we often ate there. She even acted in a student film shot at the restaurant!
Walking in, I realized it had been 23+ years since my last visit. I ordered a bacon, egg, and cheese biscuit with coffee as a group of students left, leaving me with the place almost to myself.
POTA at Strouds Run State Park (US-1994)
I arrived at the park around 9:15 AM. It had been raining all morning, so I sought cover under a picnic Shelter. Eric, a frequent activator of Strouds Run, had told me where to find all of Strouds’ shelters.
You can also read all of Eric’s hundreds of field reports on his website.
I found an empty shelter by the lakeshore (no surprise given the weather). I brought several radios with me on the Dayton trip: my Elecraft KX2, KH1, Index Labs QRP Plus, Venus SW-3B (always in the car), and my Yaesu FT-818.
Propagation has been a hot mess lately. I figured 40 meters and 20 meters would be the best bands to try, and the EFHW is resonant on both, eliminating the need for an antenna tuner.
Setup was easy, with trees near the shelter providing ideal suspension points for the EFHW.
(Note about audio: As I prepared this activation video, I discovered that my wireless mic wasn’t connected, so you won’t hear me when I walk away from the camera. My apologies! There’s also more wind noise than usual. However, you’ll hear plenty of waterfowl and other birds enjoying the park.)
Jeweler’s Bench Block
Only a couple of days prior, I received a Jeweler’s Bench Block that I purchased on Amazon.com (affiliate link). Several friends had recommended I pick up one to pair with my lightweight, portable keys that have embedded rare-earth magnets.
The key I paired with it was my BamaKey TP-III. You’ll hear me rave about this combo in the activation video.
It weighs 13.7 ounces and has a silicon base: I found that with the TP-III (which has a light action), it was rock-solid on the picnic table.
I wish I would have purchased one of these ages ago!
Gear:
Note: All Amazon, CW Morse, ABR, Chelegance, eBay, and Radioddity links are affiliate links that support QRPer.com at no cost to you.
Update as of May 31, 2024: I’ve just learned that the prototype unit I used for this activation has been superseded by a production model Xiegu X6200. While many of my initial impressions remain valid, some of the bugs and quirks I noted have likely been addressed in the production model.
When I published this post, I was under the impression that this loaner unit was representative of the final production run. In light of this new information, I’ve removed the mention of some specific bugs until I have the opportunity to evaluate the production run unit.
I’ll be receiving a production model loaner in the coming weeks, and I’ll update this post and share a video demonstrating the updated radio. Stay tuned!
After publishing my post yesterday morning, I ran a few errands in town, then headed to Lake Powhatan in Pisgah National Forest to perform a POTA activation with the new Xiegu X6200.
In short, my buddy Vince summed it all up in a text he sent, stating that I sure picked an interesting time to get on the air. I received this image from Vince–while calling CQ POTA for the 100th time–showing the results of our X-Class Flare:
It was a radio blackout.
In the end, I did log eleven stations: 1 on 30 meters, and 10 on 20 meters, all with CW.
Eventually, I did plug in an external battery and run the X6200 at its full 8 watts of power in SSB mode, but there were no takers on 20 meters. The bands were so dead, I even received reports from some of you that the FT8 portions of the band had little to no activity.
That dead!
I did manage to hunt some other park activators successfully–we activators had to work together to get through this one!
Video: Change of plans
I had originally planned to create a video of the activation, write a detailed field report, and answer some of the questions you left in the comments section of my previous post. I was actually able to make a video, but it’s incredibly long. Because of that, I’m only going to upload it to Vimeo for QRPer.com Patreon supporters to view. I simply don’t want to deal with the inevitable drive-by comments on YouTube from people expecting quick-hit thoughts about the X6200 in a nearly two-hour video.
No worries, though, I will make another video witht he X6200 in the next few days and publish that one on YouTube.
In the meantime, I’ve also taken some thorough notes that I’ll be sharing here.
X6200: Initial Impressions and Notes
Disclaimer: It’s important to keep in mind that this is a prototype loaner unit, and the firmware is still in its early stages (Version 1.0). Because of this, the following observations and notes should be taken with a grain of salt.
Many issues will likely be addressed in firmware updates that Xiegu will be releasing in the coming days and weeks.
The date of publication for this article is May 30, 2024. Considering
I will eventually be posting a comprehensive review of the X6200, but only after I’ve spent a significant amount of time (weeks, not just hours) with the radio. This initial write-up is just to share my first impressions.
Moving on…
Since there simply wasn’t enough band activity and the X-class flare created more band noise than normal, I wasn’t able to properly evaluate the X6200’s filtering (thus how it might handle a pileup, crowded band conditions, etc.). I also couldn’t get a good read on the radio’s noise floor and overall audio characteristics.
I did, however, spend nearly two full hours with the X6200 going full bore sending CQs, so I had quite a bit of hands-on time, and I feel the X6200 got a proper burn-in period.
Many thanks to Matt (W6CSN) who shares the following post from his blog at W6CSN.blog:
The Adventure you get is not always the adventure you expect. Recently I’ve been plotting a unique activation of the De Anza National Historic Trail, but that particular POTA activation is going to need a good antenna and just as importantly, time.
This day afforded a few hours in the morning for outdoor radio but not enough to retrace the steps of the De Anza expedition. Instead, I headed down to the San Francisco Bay side for a quick outdoor amateur radio session.
Marina entrance light from years gone by
Since it was was a Saturday, my usual spot at Presidio East Beach was heavily impacted by weekend recreation enthusiasts, so I continued for a quarter mile to the practically empty parking lot east of the St. Francis Yacht Club.
Small dry beach on the marina side of the jetty
Thence on foot past the old stone light tower and the clubhouse of the Golden Gate Yacht Club, you find yourself of the path to the end of the breakwater where a unique art installation sits.
Alcatraz Island at anchor off the point
The Wave Organ is a curious sculpture that uses tubes and cavities between old cemetery stones to channel and amplify the watery sounds of waves as the tides move in and out of the Bay.
Surrounded by saltwater at the end of this jetty, which by my reckoning is within the boundary of the Golden Gate National Recreation Area (US-0647), this location was perfect for the “no impact” operation afforded by the Elecraft KH1.
This granite wall served as the operating bench
My plan was to see if I could complete an activation of making 10 contacts entirely by hunting other POTA activators, perfectly reasonable given it was a weekend with no geomagnetic storms to disrupt radio propagation.
An entire station in the palm of your hand
What I did not count on was that it was a contest weekend with both 20 and 15 meters wall-to-wall with rapid fire contesters. As a QRP station, finding the POTA needles in that haystack was going to be tough.
The wave organ is a naturally contemplative environment
I retreated to 17 meters which should offer good daytime propagation and no contesters. There on 18 MHz, I was was able to collect five park-to-park contacts in a span of 23 minutes.
At that point I’d exhausted all of the 17m active CW stations on the POTA spots page and didn’t really have time to wait for more to show up. Therefore the “all hunting” activation strategy was abandoned and I commenced calling “CQ POTA.”
A fresh charge delivers nearly 6 watts into a matched antenna on 17m
The activation was “validated” with a call from Dave, AA7EE as the 10th QSO and then completed with one more park hunted, K9DXA in US-1001. Most of the contacts were with stations east of the Rockies.
One thing I learned from earlier outings with the KH1 was to not cut the log sheets too small, as might be suggested by the lines printed on the page. Without enough paper under the top and bottom tabs of the logging tray the sheets can easily be caught and snatched away by the wind.
Leave enough margin on the logging sheets and they are easily secured in the tray, even in the face of brisk Bay breezes.
Looking across the marina entrance toward Fort Mason
The “hunting only” activation plan didn’t quite work out but it was a great time out playing radio at scenic spot in San Francisco Bay.
Sailing season is well underway on SF Bay
While I didn’t expect to activate from the wave organ today, it turned out to be a fun adventure and an excellent spot from which to get on the air with the KH1.
On Saturday, May 4, 2024, I drove to the Hickory, NC area to visit my father, who had recently been released from the hospital and was starting rehab at a skilled nursing facility. I had a busy afternoon planned back home in the mountains, but I couldn’t resist squeezing in a quick POTA activation!
Many of you know this is a recurring theme for me – it’s rare that I have a lot of time for activations. I’d be doing far fewer if I couldn’t manage 45-60 minute windows to set up, operate, and pack up.
Tuttle Educational State Forest (K-4861)
The facility where my father is staying is only about 20-25 minutes from Tuttle Educational State Forest, so I had to stop by.
It was rainy that Saturday, so I was already thinking about Tuttle’s excellent picnic shelter. I had my Elecraft KX2 and AX1 antenna packed, and while operating under a metal roof with a compromised antenna isn’t ideal, I’ve had surprising success in the past, including one of my first Transatlantic Park-to-Park contacts (click here to read that field report).
I arrived at Tuttle and found that there was no one in the parking lot. Not surprising considering the weather.
I grabbed my gear and headed to the shelter, only to discover that the lights were on and it was reserved from noon to 5:30 PM. Dang!
Even though it was still drizzling, I wasn’t too concerned. Tuttle has plenty of trees, so I figured I could find a spot under a good canopy to protect my gear. I went back to the car for my rain jacket and my new folding foam seat.
A Funny Story…
I had been planning to buy the Nemo Chipper Foam Seat from REI, but a couple of days after adding it to my cart, one arrived in the mail!
It was a gift from Al (N4EII), who mentioned he loves his and uses it for SOTA and POTA because it’s so lightweight and portable. I think it was this very rainy activation that prompted him to send me the Nemo seat!
Thank you, Al, for reading my mind! So very kind of you!
Setting up
I found a picnic table under a heavy canopy and set up my Elecraft KX2 and AX1 antenna–one of my favorite radio/antenna combos.
That said, I was definitely taking a bit of a gamble. Band conditions (a recurring theme here lately) were quite rough and using a compromised antenna would be risky compared with, say, a much higher-gain 40 meter end-fed half-wave. But the AX1 is so quick to deploy, which is key when time is limited.
Gear:
Note: All Amazon, CW Morse, ABR, Chelegance, eBay, and Radioddity links are affiliate links that support QRPer.com at no cost to you.
It being midday, I decided that 20 meters would likely be the best band choice.
I started calling CQ POTA and was a bit surprised that my first contact was Michael (N7CCD) in Washington State.
Michael is in my logs a lot–even though he runs QRP from home most of the time, he has a very effective hex beam that casts a signal into NC with ease. With the bands in such rough shape I didn’t expect to work him that day.
Then again, many of the solar numbers have been healthy, it’s just that the ionosphere has been quite unstable. This usually results in deep QSB (fading) thus contacts may be strong one minute, then completely gone the next. This is how I felt conditions were at Tuttle that day.
I continued logging stations at a very respectable rate. I did note a lot of activity from 5 land (Texas and Mississippi). It’s funny how sometimes a path will open like this. Indeed, Texas has had a most welcome opening into North Carolina a lot lately.
In the end, I worked a total of eleven stations–one more than the required ten for a valid POTA activation.
I did all this in just 16 minutes on air. That’s actually an impressive rate considering propagation was so flaky.
No doubt, I could have worked more stations if I had the time.
QSO Map
Here’s what this five-watt activation looked like when plotted out on a QSO Map (it’s still hard for me to believe this can be accomplished with such a small antenna!):
Screenshot
Activation Video
Here’s my real-time, real-life video of the entire activation. As with all of my videos, I don’t edit out any parts of the on-air activation time. In addition, I have monetization turned off on YouTube, although that doesn’t stop them from inserting ads before and after my videos.
Rainy weather doesn’t stop me from activating if I have my mind set on it.
That said, when it’s raining, I do seek out parks with shelters. It makes the whole set-up process easier and quicker.
Ideally, you want your antenna out in the open, but I’ve even used quarter wave verticals in shelters without issue (I’m thinking of this Lake Norman activation in particular).
Of course, I also keep a small rainfly in my car for makeshift shelter if needed. With a rainfly, camping chair, and kneeboard, I can activate in the wettest of weather. In fact, a rainfly saved this quick Field Day activation last year.
And of course, when raining, you can always activate from inside your vehicle! That may be the easiest option of all for some of us.
Again, Al, thanks again for the Nemo seat – it’s fantastic!
Thank you
Thank you for joining me during this activation!
I hope you enjoyed the field report and my activation video as much as I enjoyed creating them.
Of course, I’d also like to send a special thanks to those of you who have been supporting the site and channel through Patreon, and the Coffee Fund. While not a requirement, as my content will always be free, I really appreciate the support.
As I mentioned before, the Patreon platform connected to Vimeo makes it possible for me to share videos that are not only 100% ad-free but also downloadable for offline viewing. The Vimeo account also serves as a third backup for my video files.
Thanks for spending part of your day with me! And today being Memorial Day, my thoughts are with families who’ve lost loved ones in service to their country.
Those of you who follow my articles know I generally activate in the morning. However, as school just let out for my son, we’ve transitioned to a summer schedule and that means horseback riding lessons are now in the morning. With my afternoons uncommitted, I’d like to give hunters who may miss me in the morning an opportunity to hunt me by activating later in the day.
Wednesday, May 22nd, I resumed my 60 new-to-me park activation goal as well as the pursuit of the WMAs near the Altamaha River by heading to Clayhole Swamp WMA (US-3740). Clayhole Swamp WMA is a 8,500 plus acre property along the south side of the Atlamaha River.
I arrived at the property around 3 PM and began looking for an activation site. I first thought to activate near the river as Glenn W4YES and I did at Sansavilla. However, I didn’t have time to drive all over the park as I wanted to be on the air at 4 PM. An hour sounds like gracious plenty of time but when you are driving up and down dirt roads in an unfamiliar area, it isn’t.
entrance roadthe woods along the entrance road
The road into the property (as you saw in a photo above) is well-packed and maintained. However, as you drive further into the WMA, other roads are less so. I found Lemmond Road and gave it a go. Given the recent rain, it was a bit on the boggy (but no less fun) side.
Eventually, it became two ruts in the forest and I appeared no closer to finding the river. Also, a multitude of flies swarmed all around the car. At this point, despite having fun mud-bogging on the road in my Subaru Crosstrek “Kai,” it was time to turn around and find a less buggy and muddy QTH.
Source: Georgia DNR – map of Clayhole Swamp WMAmud-boggin’ road!Kai needs a bath now
I retraced my path to the entrance and a little past the entrance into the WMA found a clearing off to the right. The terrain was such I could drive the car just a little way in and set up my station.
There were trees all along the side of the clearing. I donned my blaze orange vest and hat and pulled out my arbor line and weight. Amazingly, it took just one toss to get a line up and in no time, my EFRW was hoisted and ready. I oriented it southeast hoping to get good coverage to the west but also the northeast which turned out to be the case.
my antenna “mast” choicesarbor line high up in treefeed-end out in clearingAntenna orientation
The site I chose was shady so despite the afternoon temperature being in the 80s, Daisy and I were cool. I also brought along her cooling vest from Ruffwear. You wet the vest and put it on the dog. The evaporative cooling it provides can lower the temperature for the dog by 3-4 degrees. It worked. She didn’t pant at all during the activation while wearing the vest. This piece of equipment will come in handy for POTA in the summer.
Wx in Savannah before heading to WMADaisy’s cooling vest
I began with 30 meters, logging 4 contacts before moving to 20 meters. Twenty meters gave me 11 contacts, including a park-to-park (P2P) QSO with John W4ER at US-3691 in Alabama. Continue reading A Pretty Picnic for the POTA Babe→
The more I use my Penntek TR-45L “Skinny” the more I love it.
Although, in truth, I loved it from day one because it’s just a flatter, more portable version of my original TR-45L.
The audio is wonderful, the controls are simple, and the receiver is top-shelf. Any excuse to take it to the field!
On Sunday, April 28, 2024, I made a quick trip to visit my father in Hickory. He was still in the hospital at that point and I wanted to spend the morning with him and get updates from his specialists and doctor. He was improving which was a very good thing indeed.
After spending a few hours with my dad, I could tell he wanted to take a nap, so I thought it a good time to head back home, with a short detour at Lake James.
Lake James State Park (US-2739)
It was an absolutely beautiful day to be outdoors. I expected Lake James to be packed on a Sunday, but the Catawba River Access wasn’t too terribly busy. I imagine the more popular Paddy’s Creek Access was much busier.
I decided to set up at a picnic table close to the parking area–one I’ve used before and one that makes it easy to deploy an end-fed half-wave without creating a tripping hazard for others.
My EFHW simply disappears among the trees which is why it’s important to deploy it in a space where other park visitors won’t walk.
I deployed the 40 meter EFHW that Steve (MW0SAW) made for me a couple years ago.
Setting up the TR-45L was easy enough especially since the padded bag Penntek sells so easily accommodates all of the items needed for an activation. In fact, it is spacious enough I could easily put an antenna and feed line inside, too, but I opt to simply carry those in my backpack.
With everything set up, it was time to hit the air!
Gear:
Note: All Amazon, CW Morse, ABR, Chelegance, eBay, and Radioddity links are affiliate links that support QRPer.com at no cost to you.
With band conditions having been so unpredictable lately, I wasn’t sure what to expect. My schedule only allowed for a short activation, so I hoped to wrap things up within 30 minutes.
Twenty meters seemed like the most promising band, and thankfully, it was in decent shape. I started calling CQ POTA, and to my delight, the first ten stations were logged in a mere ten minutes! It doesn’t get much better than that.
I continued making contacts for a few more minutes, logging four additional stations. Then, with the band quieting down, I decided to call it a day.
I would have loved to spend more time on the air, but I was also eager to get back home to my wife and daughters. Sometimes, a short activation is all you need.
QSO Map
Here’s what this five-watt activation looked like when plotted out on a QSO Map:
Activation Video
Here’s my real-time, real-life video of the entire activation. As with all of my videos, I don’t edit out any parts of the on-air activation time. In addition, I have monetization turned off on YouTube, although that doesn’t stop them from inserting ads before and after my videos.
On a bittersweet note, I mentioned previously that John (WA3RNC) is closing down the Penntek shop this year and will no longer manufacture transceivers. If you haven’t already placed an order for a Penntek transceiver, you might not be able to snag one at this point. I would check the updates on the Penntek site for more information. I felt John’s radios were so unique and packed with proper field performance.
The original TR-45L pictured here at Lake Norman
Then again, at 77 years old, John deserves to enjoy his retirement to the max, so I’m happy for him.
My Penntek TR-35
I know I’ll never sell my Penntek radios and I’ll do all I can to take care of them so they serve me over the long haul! I’ve no doubt that they will.
Thank you
Thank you for joining me during this short POTA activation!
I hope you enjoyed the field report and my activation video as much as I enjoyed creating them!
Of course, I’d also like to send a special thanks to those of you who have been supporting the site and channel through Patreon, and the Coffee Fund. While not a requirement, as my content will always be free, I really appreciate the support.
As I mentioned before, the Patreon platform connected to Vimeo makes it possible for me to share videos that are not only 100% ad-free but also downloadable for offline viewing. The Vimeo account also serves as a third backup for my video files.
Thanks for spending part of your day with me! Have an amazing Memorial Day weekend!
QRP radios, product announcements, reviews, news and more. Low power amateur radio fun!
Please support QRPer by adding us to your whitelist in your ad blocker. Ads are what helps us stay online. All of our ads are ham radio related--no junk, we promise! Thank you!
I was excited about visiting Whitewater Canal because it would be my first official POTA activation in Indiana.
We arrived around 1:00 PM and opted to grab lunch at a nearby pizzeria before activating.
Around 2:00 PM, we grabbed our gear from the car and walked across the road to the park grounds.
The Whitewater Canal State Historic Site offers a glimpse into the 19th-century canal era.
Built between 1836 and 1847, the Whitewater Canal was a 76-mile waterway that connected the Ohio River to Hagerstown, facilitating the transport of goods and agricultural products.
This engineering feat played a vital role in the economic development of the region, contributing to the growth of towns and industries along its path.
I’ve always been fond of railroads and canals, so this site was brilliant as it featured both running parallel to each other!
Eric, Brian, and I (Miles didn’t activate) were careful to set up within the actual park boundaries.
In this case, it was a little difficult to determine the exact boundaries because the town and park blend together.
Eric set up his Elecraft KH1 station at a picnic table under a large tree.
Brian’s site was super stealthy behind the sign–since he operated with earphones, you couldn’t hear him and barely could see him!
