All posts by Thomas Witherspoon

News, Product Announcements, QRP, QRP Radios

WA3RNC introduces the Penntek TR-45L “Skinny” and reservation form

4 Comments
Photos by WA3RNC

Many thanks to John (AE5X) who notes that John (WA3RNC) has release information about his new TR-45L “Skinny” design. 

Here’s the information WA3RNC shares on the Penntek website along with an update about the kit version of the TR-45L (non-skinny version):

TR-45L Kit Version Update

The kit version has been delayed for the time being due to several (most) beta builders experiencing frustration with the process of assembling the front panel onto the main board with 15 loose and unsoldered switches, jacks, and controls. These issues indicate that the TR-45L kit version will most likely be offered as a semi-kit with the main board being largely factory assembled, leaving the pre-aligned plug-in RF board in kit form. The internal battery option would be available in this kit version, but not the Z-Match ATU.

TR-45L Skinny (left) TR-45L (right)

A second kit version in a thinner housing is also being considered (see the TR-45L “Skinny” photos). This version would be offered with no options available (other than a $20.00 tilt bail) as there is no room inside the thinner housing for the internal battery nor the ATU option. It does, however, contain an internal speaker. Unfortunately, while greatly simplifying construction, these semi-kits will erode the normally expected cost savings with a kit. The best guess price for these TR-45L semi-kits would be around $500.00. We welcome your thoughts and opinions on these semi-kit concepts.

For those interested in signing up for the reservation list, you can use the reservation form linked here. Be advised, it could take up to 6-8 weeks until they are ready to be shipped.

The TR-45L has been a long time coming, and I thank you for your patience during the development cycles with parts procurement issues due to the covid pandemic. Let’s hope that the ugly covid experience is behind us…

In a nutshell, the TR-45L Skinny will simply be a TR-45L in a skinnier chassis with no option for an internal battery nor Z-Match ATU, but will still have an internal speaker. 

For those of you who don’t care for the Z-match or internal battery, the TR-45L Skinny will certainly be more portable and less bulky than the original TR-45L.

I suspect the performance will be identical. I’m sure the internal speaker will work well, but I will be curious if it sounds as full-fidelity as the original TR-45L. I might ask John for a loaner to check it out once released!

Again, if interested in this variant of the TR-45L, you might wish to fill out the reservation form.

Accessories, Antennas, Articles, Field Reports, Guest Posts, News, Portable, QRP, SOTA

Steve tests the Gabil 7350T antenna, Gabil GRA-ULT01 tripod, and BaMaKeY TP-III paddles

10 Comments

Many thanks to Steve (MW0SAW) who shares the following field report:

Mini Field Report: Testing the Gabil 7350T and BaMaTech TP-III on a brisk SOTA activation!

by Steve (MW0SAW)

Went for an early walk/SOTA activation up Fan Fawr GW/SW-005 (734m) this morning (9/4/23). I think someone said it was supposed to be the hottest day of the year in the UK. It was about 5 deg celsius with a bitter wind chill of -2c on the summit! It’s very close to the highest peak in South Wales, Pen Y Fan (886m).

As I mentioned a couple of weeks ago in our emails, I wanted to test a new compact antenna I purchased recently, called the Gabil 7350T in the USA, and branded as the Sharman MD-3500 in the UK where I got mine. I also took the Gabil GRA-ULT01 MK2 tripod which I did purchase from the USA on Amazon.com.

The Gabil 7350T Compact Antenna and Gabil GRA-ULT01 MK2 tripod

Another first for the the activation was the Bamatech TP-III ultra compact paddle, Dinos were included 🙂

Starting my walk, the lovely view of the reservoir quickly disappeared and was the last view I would see ascending into the mist.

I took refuge in my Decathlon 1 man camping shelter, setting up the tripod and antenna close by.

The wind was howling and turning my back the antenna toppled over. This was quickly resolved with a tent peg on one of the tripod legs. Quick setting of the slider with the analyser got 1.2 SWR and so after a slurp of coffee, I started to call CQ on 20m CW. A nice stream of European qsos ensued with good reports (many 599), it was pleasing to hear with such a small antenna (about 8 ft). Just as the contacts were drying up, I was taken aback by a strong VK station! Always great feeling to get some dx like that but especially pleasing with this tiny antenna on its maiden voyage 🙂

I switched to 20m SSB for a few more QSOs but struggled with QRM on two frequencies. My allotted time was running low and my fingers were numb, so I packed up the HF and got the handie out to catch a few local VHF contacts.

So what can I summarise from this activation, well I can safely say I love the Gabil/Sharman antenna and Gabil tripod. They would make a really nice additional to a small go bag, they seemed to work almost as good as a full size 1/4 on 20m. Time was limited this trip and I was too cold to hang about to try more bands, but extremely pleased with the performance so far.

The Bamatech key is a pure work of art, beautifully made, sensitive and precise. Probably my best portable key to date in my collection.

Equipment:

(Note: Amazon links are QRPer.com  affiliate links.)

Thanks to all the chasers.
73
de MW0SAW/P

Accessories, Field Reports, Kits, News, Portable, POTA, QRP, Videos

POTA at Fort Dobbs: Testing a BCI filter and depleting a battery!

11 Comments

Friday, March 17, 2023 was a dreary, rainy day.

It was the sort of day made for reading a good book by the fireplace or…in my case…activating a park!

I don’t let rain stop me from playing radio in the field. I carry a rain fly in my car pretty much all of the time so if push comes to shove, I can create a dry space to play radio.

That said, a number of parks I frequent have large covered picnic shelters, so why not use what’s already there?

That particular Friday, I had one particular park and one particular goal in mind.

G106 + BCI Filter

As I mentioned in a post this weekend, I purchased and built a K9DP BCI Filter Kit.

If you’d like to see photos of the build, check out this post.

I built this BCI filter specifically to pair with the Xiegu G106 transceiver. Why? Because the G106 is prone to overload if you’re anywhere near an AM broadcaster.

The last time I visited Fort Dobbs State Historic Site (K-6839), a local AM broadcaster bled through the audio of the G106. I was able to complete the activation without any issues at all–in fact, it was a very successful activation (read the report here).

Still, I did feel that the receiver was a bit less sensitive due to the broadcaster overwhelming the front end of the radio.

That Friday, I wanted to pair my Xiegu G106 with the new in-line BCI filter to see if that might mitigate the interference I experienced before.

Fort Dobbs State Historic Site (K-6839)

After arriving at Fort Dobbs, and before taking my gear out of the car, I made my way to the park office (in the log cabin at the end of the sidewalk above) and asked for permission to use their picnic shelter. Continue reading POTA at Fort Dobbs: Testing a BCI filter and depleting a battery! →

Hacks and Hints, How To, Kits, News, Skills

Video: Alan’s method for winding toroids

10 Comments

After posting my article about the K9DP BCI filter kit build, Alan (W2AEW) commented:

If you dislike winding toroids, the method I show in this video makes it a lot easier!

This is an excellent way to handle the toroid while winding. Check out his video below:

Click here to view on YouTube. 

Alan has a massive library of instructional videos on YouTube. If you haven’t already, subscribe to his channel!

Field Reports, Guest Posts, Morse Code, News, Portable, POTA, QRP

Brian’s Reflections on Activating a Not-so-New Park

2 Comments

Many thanks to Brain (K3ES) who shares the following guest post:

The Visitor Center at Kinzua Bridge State Park (K-1366) is well worth a visit.  It provides an excellent overview of the history, use, and collapse of the railroad bridge that gave the park its name, and it provides an excellent view of the pedestrian skyway built on the portion of the bridge that remained standing after the tornado that caused the collapse.

Reflections on Activating a Not-so-New Park

by Brian (K3ES)

Monday, April 3 was one of those beautiful, warmish (60ºF or 16ºC) sunny days in northwest Pennsylvania that remind us that spring is really here.  Only a week earlier, we had an unexpected snow fall that covered the ground (and it will likely not be our last snow of the season).  So my wife, her father, and the dogs all looked forward to getting out of the house to enjoy the weather.  We packed for a picnic, and drove through bright sunshine to Kinzua Bridge State Park.

After a picnic lunch, and while Becky and her dad explored the visitor center and walked the dogs, I set up for a Parks on the Air (POTA) activation of K-1366.  This would be my first activation of the park, but not my first visit.  I have been there several times before, including an excursion trip behind a steam engine that took me across the railroad bridge over Kinzua Creek and back.

A view from the visitor center of the pedestrian skyway.  It was constructed on the structure that remained after the bridge was struck by a tornado in 2003, causing its partial collapse.

An Historic Park

Kinzua Bridge State Park has an interesting history.  The railroad bridge that gives the park its name was originally built of wrought iron in 1882.  At the time it was built, the 301 ft (92m) high and 2052 ft (625m) long railroad bridge was the highest in the world.  It was rebuilt in place in 1900, replacing iron with steel, to strengthen it for the heavier trains that needed to cross.  The bridge remained in commercial service until 1952, and was later sold to the Commonwealth of Pennsylvania for a State Park.  The bridge continued to support excursion trains and pedestrian traffic until 2002, but was struck by a tornado in 2003, causing its partial collapse.  Today, the remaining part of the bridge has been rebuilt as a pedestrian skyway, complete with a glass floor at its end to look down at the valley far below.

The visitor center provides an excellent multimedia overview of the economics, technology, and history of the structure.  It is well worth a visit.  Similarly, the skyway gives a spectacular view of the structure, the collapsed towers, and the surrounding Pennsylvania forest.  The park has picnic facilities and hiking trails, and a trailhead for the rail trail that has repurposed the old railroad right-of-way.

This is a view of the picnic pavilion from my operating position.  The picnic area also has a number of other open picnic tables and a playground area for the younger crowd.

The Setup for Activation

I stopped into the visitor center to let the staff know of my intention to activate.  I found them to be friendly and accommodating, which always makes activating a pleasure.  I do my best to be a good ambassador for amateur radio and the POTA program.

For activating, I set up at a remote picnic table.  Three tosses got the throw line over a good branch to support my Tufteln 9:1 random wire antenna.  A 15 ft RG-316 cable connected the antenna to my Elecraft KX2.  Completing the station were a 3 Ah LiFePO4 battery, a set of generic earbuds, and VK3IL pressure paddles.  I used a clipboard to keep my notepad from blowing around in the breeze, while I logged with a mechanical pencil.

The picnic table operating station used to activate K-1366.  Included are the KX2, VK3IL pressure paddles, clipboard and log.

The Activation

As I finished getting the station ready to go, it occurred to me that I had a frequency-agile-antenna and rig, a bit more than an hour to operate, and no other operators in the area.  So, I took the opportunity to try for contacts on as many bands as possible, inching my way toward the POTA N1CC Activator award for making contacts on 10 bands from 10 parks.  The park has good cell coverage, so I was able to use my phone to spot myself.  After that, I mostly left things to the Reverse Beacon Network and the POTA spotting gateway, but I was able to use the phone to confirm that my changes in frequency were picked up.

In 70 minutes of CW operation at 5 watts, I made total of 26 contacts, including at least one contact each on the 10, 12, 15, 17, 20, 30, and 40m bands.  An apology to the hunters may be in order, because I was harder-than-usual to contact.  After making a contact on each band, I would QSY to the next at the first significant lull in the action.  I look forward to another trip back to K-1366 to try for contacts on the 3 additional bands needed to complete its activation toward my N1CC.

As you might guess, by using multiple bands, the contacts came from both far and near:  as far as Spain to the east and Oregon to the west, and as near as New York, Pennsylvania, Ohio, and Michigan.  Middling distances were also well represented in the log.

It was a good day in the park, and here is the contact map from a 7-band activation of K-1366.

Equipment

Note: Amazon links are affiliate links that support QRPer.com.

Conclusion

This outing made for a fun and productive afternoon that was all the more enjoyable for sharing it with my family.

It also made for a great opportunity to shake off the winter blahs, and it held the promise of beautiful spring and summer days for more park activations.

Best 73 de Brian – K3ES

Here is a bonus picture of another semi-famous bridge in northwestern Pennsylvania (it actually has its own Facebook page).  This is Nebraska Bridge, which provides a convenient shortcut across Tionesta Creek.  We knew we would have to take the long way around, but stopped for a look anyway.  Unfortunately the bridge floods several times a year (sometimes becoming completely submerged), because it is located in the upstream end of the reservoir behind the Army Corps of Engineers’ Tionesta Creek Dam.  We had over an inch of rain last week, so the bridge is partially under water.  On the brighter side, 100 miles downstream, the City of Pittsburgh did not flood.
Accessories, Articles, How To, Kits, New Products, News, QRP

Assembling a K9DP BCI Filter Kit (Photos)

6 Comments


If you own a Xiegu G106, X6100, or any other radio that is prone to overloading when in the presence of an AM broadcaster, you should consider building an in-line BCI filter!

As many of you know, I’ve been testing the Xiegu G106 over the past couple of months for a review that will be published in the May 2023 issue of The Spectrum Monitor magazine.

One criticism of the G106 is that its front-end overloads when there’s an AM broadcaster within a few miles of where you choose to operate. The Xiegu X6100 is identical in this regard.

One quick way to remedy this is to build or buy a BCI filter. We’ve mentioned in the past how you can homebrew them and I planned to do so. After checking my parts drawer, though, I realized I needed to buy a capacitor, toroids and at least one of the two BNC connectors needed if I wanted an in-line filter in a small project box.

I decided it would be much easier to simply buy a kit and, based on a tip from a reader here on QRPer.com, I purchased one from Dan (K9DP). Continue reading Assembling a K9DP BCI Filter Kit (Photos) →

Field Reports, Morse Code, News, Portable, POTA, QRP, QRPp

QRPp POTA: How many hunters can I possibly log with only 100 milliwatts–?

6 Comments

As I walked out the door on the morning of Tuesday, March 21, 2023, I grabbed my Elecraft KX2, MM0OPX 40 meter end-fed half-wave, and a key I hadn’t yet taken to the field: my Bamakey TP-III!

I had a full day of errands, appointments, and carting my daughters to/from school, but I also had a good 90 minute window to play radio!

As I’ve mentioned previously, the Vance Birthplace (K-6856) is incredibly convenient this particular school term. I pass by it twice a week, and I feel incredibly fortunate because it’s a wonderful POTA site with POTA-friendly staff. They all know me quite well there at this point.

The Vance site is a small park and the only negative (from the point of view of a POTA activator) is if you have poor timing, you might arrive only to find that a large school group has taken over the site. This is especially a concern on weekdays during school hours–in other words, the time I usually activate Vance.

I pulled into the Vance site that morning and there were no vehicles there other than park staff. A good sign so far!

The only appropriate spot to activate at Vance (if you operate a portable HF station) is in or near the picnic shelter. The rest of the site is where visitors wonder through the old homestead and take guided tours.

I never set up my station in the middle of park activities or in a viewshed.

At the end of the day, we represent all Parks On The Air activators and the amateur radio community at large when we’re in public spaces. The last thing we want to do is detract from others’ park experience.

Before pulling any gear out of the car, I walked into the visitor center and asked the park staff for permission to set up in the picnic shelter. I always do this because if a school or tour group is scheduled to visit the site that day, they almost always need the picnic shelter and have it reserved.

Fortunately, no one had scheduled the picnic shelter, so the park ranger told me, “It’s all yours! Have fun!”

Proper POTA Flea Power!

I like shaking up each new activation in some small way so that it’s not a carbon copy of any previous activation.

Since, like most POTA activators, I visit the same local parks the bulk of the time, it adds a little extra challenge and fun to try different gear combinations, experiment with new antennas, or even (as in this case) try different power settings–! Continue reading QRPp POTA: How many hunters can I possibly log with only 100 milliwatts–? →

Digital Modes, Field Reports, Guest Posts, News, Portable, POTA

Scott’s Georgia Parks On The Air weekend field report

2 Comments

Many thanks to Scott (KK4Z) who shares the following post from his blog KK4Z.com:

Georgia Parks on the Air at FD Roosevelt SP K-2173

Friday evening, Mary K4SEZ and I traveled to FD Roosevelt State Park for a weekend in a very nice cabin. The cabin is located on Pine Mountain with some exceptional views. As you can guess, I brought some radios with me. I went QRV right before 1800 hrs. local to make sure all my equipment worked prior to the contest. Besides, the contest I had a regional HF net that I needed to check into Saturday morning. The contest starts at 0800 hrs local Saturday and the net was also at 0800 and lasted about 20 minutes.

Friday night was amazing! Twenty and forty meters was wide open. Using FT8, I made 223 contacts between 1800 hrs Friday and 0300 hrs Saturday morning. I worked stations as far west as Japan and Australia and as far east as Rwanda, Ukraine, and European Russia. Unfortunately, the rest of the weekend was not near as exciting. Between 0800 hrs Saturday morning and 1230 hrs Sunday, I made an additional 477 contacts. The bands were up and down and the pace was a little slower. I worked 48 States and 34 countries when it was all said and done. Sunday morning had an opening on 10 meters and I made 19 contacts many into Europe. In total, I had 700 contacts.

My antenna was my tried and true homebrew 28.5-foot random wire antenna which I named my K4SWL antenna as the original idea from Tom.  It uses one 17-foot counterpoise.  On this trip, the wire I used was 14 ga (I think), coated Flexweave I got from The Wireman many years ago.  I was using some 20-something gauge I got from SOTABeams but because I use this antenna a lot, I worried about the thin wire breaking.  I use a 9:1 UnUn with a 1:1 current BalUn to help with matching.  The antenna is matched by an LDG RT/RC 100 matching unit.  This is fairly new to and so far I like it. The tuning circuit out by the antenna helps keep stray RF out of the shack. It was also quite windy here Friday night and Saturday.  The antenna held up well.  The only issues I had were some of the sections on my MFJ push-up pole would collapse affecting the tuning.  This pole is probably nearly 20 years old and should be replaced.

The radio was “The Rock” my IC-7300. I ran FT8 the whole time at 35-45 watts and the temperature gauge on the radio never moved past cool. Now that the FTDX10 has found a home in the shack, it’s nice to have my old friend back in the field with me.

The cabin is located on the ridge line of Pine Mountain, elevation ~1250′ ASL. Besides great views, it also gave my antenna a large aperture which may account for the many DX contacts I made.

I mainly worked FT8 as I also had to listen to a couple of conferences on the Internet and didn’t want to disturb my wife when she was doing things other than radio. We had a nice weekend away and of course, being able to bring radios is a huge bonus. When I get back home and settled, I may send the log to the GA POTA people. I don’t really contest anymore but they might find it useful for cross-checking.

Here is a YouTube Video of the activation.

Click here to view on YouTube.

Click here to read this post and much more at KK4Z.com!

Accessories, Field Radio Kits, Grab And Go, New Products, News, Portable, POTA, Reviews, SOTA

First look at the Blue Ridge Overland Gear Gadget Bag

14 Comments

In early February, Jeff (KD4VMI) sent the following message to me:

Good evening. Love your YouTube videos and QRPer posts and, from them, I know you appreciate rugged packs and gear.

I enjoy POTA, although I don’t get out as often as I’d like, but I’ve found Blue Ridge Overland Gear’s various bags and modular systems to be very handy for bundling my radios, batteries, cables, and antennas.

It’s been on my mind for some time to let you know about them (if you don’t know about them already) and I finally decided to take the time to write you. I’m not associated with them in any way, and I didn’t approach them about passing this on to you, or anything like that. I just really appreciate their gear and I think you might, too.

The BROG materials are high quality and stout, the zippers are beefy and smooth, everything is double or triple stitched and everything is modular so it can be used for just about anything, and in pretty much endless combinations with their various bags and gear.

Their products are not overly cheap, but are guaranteed for life. They’re located in Bedford, Virginia and all their things are made in the USA (I think mostly in Bedford).

I often use their tire puncture repair kit bag, for instance, to carry my FT-891, Bioenno battery, cables and mic, and PackTenna, and then strap the coax to the Molle system on the front of the bag.

They posted a YouTube video showing their gadget bag with accessory pouches for HTs, etc.

Their website is: https://www.blueridgeoverlandgear.com/.

Anyway, I appreciate all you do for our great hobby and just wanted to share this info.

Take care and all the best to you and yours…

Thank you so much for the kind words, Jeff, and for the tip about Blue Ridge Overland Gear (BROG). You’re obviously a skilled pack enabler because you had my attention by the second paragraph–!

Shortly after my exchange with Jeff, I checked out the BROG website and was really impressed with their line-up of packs and gear–all with a focus on modular organization, especially in-vehicle since it’s for Overlanding. It’s just the icing on the cake that their gear is made in the USA.

I was very curious if their Gadget Bag, in particular, would lend itself to being a modular flied radio kit pack.

Thing is, there are so many options and configurations for the Gadget Bag, I wasn’t entirely sure what to order.

Being a fellow who expects to pay a premium for rugged products, made in the USA–especially ones that carry a lifetime warranty–I was prepared for some sticker shock. Turns out, BROG pricing is pretty reasonable in comparison with other cottage industry pack manufactures.

Still, I wasn’t quite sure how easily some of my radios and gear might fit in their zippered pouches, so I reached out to BROG–mentioning QRPer and my constant search for field radio packs–and asked if I could order some packs and pouches, test them with my radio gear, then pay for what I decided to keep.  I didn’t want free gear, I just couldn’t tell based on the product images and posted dimensions what pouches and packs might fit my various radios and accessories. Also, I knew readers might ask if certain pouches and packs might fit certain radios.

The good folks at BROG kindly obliged, so I asked for the following list of items:

– QTY 1 Gadget Bag (shell) in black
– QTY 3 Large Velcro Pouches
– QTY 6 Medium Velcro Pouches
– QTY 1 Velcro Cord Keeper
– QTY 1 Medium GP Pouch
– QTY 1 Velcro Headrest
– QTY 1 Headrest Pouch Kit

Some of these items weren’t in stock, so it was a week or so later when I received notification that the package had shipped. It arrived a couple days later.

I love the feed bag style packaging, by the way.

Photos

Although you’ll start to see this field kit in upcoming activation videos, I thought I share a photo tour of this pack… Continue reading First look at the Blue Ridge Overland Gear Gadget Bag →

Field Reports, Morse Code, News, Portable, POTA, QRP, Videos

Finally did it! First POTA activation with my new-to-me Yaesu FT-891

23 Comments

Yep. I finally did it.

Over the past few years, I’ve received numerous requests to check out the Yaesu FT-891 HF transceiver. Almost all of my ham friends have one and they are widely considered one of the best 100 watt HF radios for park activators. Indeed, I bet it is *the* most popular 100W radio among POTA activators.

I’ve been tempted to ask Yaesu for a loaner model and I even came within one button click of ordering a new FT-891 from DX Engineering during a Black Friday sale in 2020.

I’ve resisted the FT-891 temptation, though, because I tend to use smaller, more portable QRP radios in heavier POTA rotation. I knew if I purchased an FT-891, it just wouldn’t get a lot of field use. It also demands a beefier field battery due to its current requirements and, frankly, it’s so rare I run more than 5 watts (and 5 watts is the lowest power setting on the ‘891) I would simply have a lot of radio for my needs.

A few weeks ago, however, a friend reached out because he wanted to sell his FT-891 and 30Ah Bioenno battery and downsize to a smaller field portable radio like the Xiegu X5105. Long story short, we worked out a trade/purchase which included the ‘891 and his battery. I had been thinking about a large capacity battery to use as a backup in the shack, so this worked out well for both parties.

Zebulon B. Vance Birthplace (K-6856)

On Tuesday, March 14, 2023, I once again had an hour to fit in an activation at the Vance Birthplace before picking up my daughters at school. I’ve really enjoyed the opportunity to play radio at Vance so much during this particular school term; next term, it’s unlikely I’ll have this opening, so I’ll enjoy it while I can!

I deployed the Chelegance MC-750 vertical again. I’ll admit that it’s so convenient keeping an antenna in the car trunk/boot that can be made resonant so easily from 40 meters and higher.

I was going to show the antenna deployment again in my activation video, but received a call and decided to deploy the antenna while finishing up the phone call. It only takes a couple of minutes to set up.

Next, I connected my 15Ah Bioenno battery to the FT-891. Even though I was only using five watts, the ‘891 needs more capacity than the 3Ah packs I normally carry with my QRP rigs.

I also connected the Begali Traveler key–I do love this key (thanks again, Jackie!). Continue reading Finally did it! First POTA activation with my new-to-me Yaesu FT-891 →