Many thanks to Teri (KO4WFP) for the following guest post:
The Dipole Does It for Wheeler NWR (K-0161)
by Teri (KO4WFP)
After my last activation, I was hankering to try the AX1 and Pacific Antenna 2040 trap dipole during the same activation for a comparison. Now, I know some of you are saying, “Well Teri, there would be no contest!” Yes, however, in the interest of learning first-hand, I headed to K-0161, Wheeler National Wildlife Refuge while visiting a friend, Glenn W4YES, and his wife in Decatur, Alabama.
Wheeler National Wildlife Refuge was established in 1938 as a wintering area for ducks, geese, and other migratory birds. It is a 35,000 acre refuge located along the Tennessee River near Decatur, Alabama. Today, the refuge attracts thousands of wintering waterfowl and cranes each year and is a winter home to the endangered whooping crane who first arrived in 2004.
I opted to set up in a parking lot on the north side of US Highway 67 which runs through a small portion of the refuge. As there were no picnic tables present, I chose a spot where the trees would shade me from the early morning sun while sitting in my Subaru Crosstrek. Since the last activation, I had given some thought as to how to set up better in the car. My code buddy Caryn KD2GUT sits in the backseat for POTA with one seat flipped down providing a ready-made table for equipment. Even better, I discovered the back of the rear seat in the Crosstrek has a rubber surface and I could secure the key to it with fun-tak!
Since the last activation, the more I worked with the Mini Palm Paddle, the more I realized I did not like it. It just felt too “squishy” for my taste and I had difficulty feeling the characters. Glenn has a solid state CW paddle by 9A5N he was not using. I worked with it a bit and really liked the stiffer feel. He removed the heavy base in which it was mounted and built a lighter base out of the back of a old diskette so I could take the key with me to Nova Scotia. (True ham radio – making use of whatever we have on hand to solve a problem!) I find the more I use this key, the more I like the feel of it.
This was Glenn’s first POTA activation and I was happy to have him along. We arrived around 8:05 AM and began setting up, first putting the AX1 on the roof of the car and then the trap dipole on a mast on a hitch mount given to me by Jack NW4TF of my local club. Continue reading KO4WFP: The Dipole Does It for Wheeler NWR→
Many thanks to Teri (KO4WFP) for the following guest post:
A Rock Leads to an Unexpected POTA Activation
by Teri (KO4WFP)
Sticks and stones may break my bones, but a rock can change the trajectory of one’s week.
Monday, while driving to the barn, a rock landed on my windshield leaving a chip in the glass. The soonest and closest appointment was in Bluffton, South Carolina. But having to work the appointment into my week, nixed my planned POTA activation for Wednesday at Wormsloe K-3725. However, I thought to check for any parks near Bluffton and yes, Victoria Bluff Heritage Preserve, K-9197, was within 15 minutes of my appointment. I could fit in an early activation before the appointment and put the AX1 to use for the first time. (Score!)
The drive Tuesday morning from Savannah, Georgia to Bluffton, South Carolina was scenic – lush, green foliage along the road interspersed with salt marsh and freshwater views.
The Victoria Bluff Heritage Preserve is 977 acres and has four miles of easy hiking trails. The warning on the SC Trails website about protective clothing & insect repellent for the large number of ticks that flourish in the preserve’s forest encouraged me to set-up in the parking lot. There were no picnic tables (my usual set-up) present so I planned on operating out of my car, a first for me.
However, how was I to mount the AX1 while sitting in my car since I had no tripod? I was still puzzling over this the morning of the activation when I remembered the Joby Gorillapod stand I purchased last year. Would the tripod mount for the AX1 work with it? Yes! It did. Continue reading A Rock Leads Teri on an Unexpected POTA Activation!→
(As is my usual, this article has a bunch of links – click on as many as you wish to receive the full experience)
by Vince (VE6LK)
In May of 2023 I embarked on a two week vacation to Hamilton Ontario, the city of Waterfalls. And I found myself with a spare 30 minutes so I decided to squeeze in an activation.
And as I am an opportunist, I made this decision at 23:25’ish z and I had not yet arrived at the park but the target was only a few minutes away! I would have until 23:59:59z to complete it if I were to be successful. “It’s time to break out the Elecraft AX1 antenna I bought at Hamvention last week“ I think to myself. It would be my first time using the antenna. I had pre-read the instructions and knew what had to be done in order to set it up.
The whole thing would unfold like a Formula 1 pit stop, albeit a wee bit slower <grin>.
Many thanks to Conrad (N2YCH) who shares the following field report:
“Fly-Away Kit” QRP POTA Activation
by Conrad Trautmann, N2YCH
4/15/2023
The National Association of Broadcasters convention is an annual event that takes place every April at the Las Vegas Convention Center in Las Vegas, Nevada. This year, I traveled to the show for work and made some time to activate a park and get another state ticked off my “Activated US States” list. I also didn’t want to miss getting the Spring 2023 Support Your Parks Weekend activator award.
A colleague suggested I visit Red Rock Canyon National Conservation Area, K-7494. The park, which is operated by the US Bureau of Land Management, has a 13 mile scenic drive that has various parking areas you can stop at to get out and explore. Red Rock requires a reservation to visit and costs $20 to enter the scenic drive area. There are places within the park you could activate for free, but I took advantage of my military veteran benefit of free admission and drove the trail and activated at one of the scenic overlooks.
Before I traveled, I had to decide what radio and antenna to bring. I selected the Elecraft KX3 and the AX-1 antenna. Not having to check a bag was key to deciding what to take.
I packed the cables, battery and computer in my brief case and the radio and the AX-1 antenna went into my carry-on bag. I did get pulled out of line by the TSA at JFK airport, but the TSA agent was very nice and just asked a few questions and let me through with no issues.
Before I traveled, I took a look at the park page on the pota.app website and saw that Colin, AK7LV, was the park leader in QSO’s. I looked him up on qrz.com and sent an email asking if he had any good advice for me or could give me some pointers. He responded quickly with suggestions of his favorite locations, how to get to them and even a suggested location where I could pick up a twofer at a trail that crossed through the park. He said I should call him when I get into town. Continue reading N2YCH’s “Fly-Away Kit” QRP POTA Activation→
On Saturday, February 18, 2023, I had a rare opportunity: a full day to play radio.
Instead of doing a five park POTA rove, I chose instead to do a summit activation followed by a park activation.
I published the summit activation on Moore’s Knob (W4C/EP-001) a couple weeks ago and planned to immediately follow that up with this report from my POTA activation at Pilot Mountain State Park (which I activated the same day).
In the process of moving my videos from the camera, to my laptop, and then to PC where I do my remote uploads (my bandwidth at the QTH is far too poor to upload large videos) I somehow managed to delete this particular video file.
I was quite frustrated, actually, because this particular POTA activation was challenging. Lately, I’ve had so few examples of just how quiet a band can be when propagation is less stable.
The SOTA activation I performed only a few hours earlier had some of the deepest pileups I’ve ever experienced. By the time I started my POTA activation a couple hours later, all of this had changed–at least on the bands above 20 meters and I’d chosen 17 meters (a WARC band) since a contest was in progress on 20 and 40 meters.
I’m incredibly pleased that I stumbled upon the raw video files on my backup drive. I was able to reproduce the video in its entirety. I’m so pleased it wasn’t lost!
This is why it’s a little out of sync date-wise with my other reports.
I hope you enjoy this field report:
Pilot Mountain State Park (K-2750)
After capping off a beautiful 4+ mile hike and SOTA/POTA activation at Hanging Rock State Park, I put my SOTA pack in the car and drove 30 minutes to Pilot Mountain State Park.
It being a gorgeous Saturday afternoon, the park was so full of guests the parking lot was completely full. A park ranger had incoming cars form a line and he allowed cars in as guests departed one by one. When I arrived, there were five cars in front of me. I was very tempted to do a three-point turn and head back down the mountain to the visitor’s center to do the activation. There was plenty of parking there. Continue reading Propagation changes make for a relaxed 17 meter POTA activation at Pilot Mountain State Park→
Many thanks to Keith (KY4KK) who shares the following report:
Extreme QRP – Testing the AX1 with WSPR and 20mW
by Keith (KY4KK)
Thomas, thanks for all of your activation videos related to the Elecraft AX1 antenna. I ordered one the day you announced the package deal, and it arrived in less than a week. I’ve activated a few parks with it already (20m SSB). Like you and many others, I’m impressed.
About a year ago, a friend (NG4S) loaned me his pair of WSPR transmitters and suggested that I explore building and comparing antennas. I’ve been hooked on antennas of all kinds and WSPR since then.
I began doing WSPR tests on the AX1 the day after it arrived. With two transmitters set to the same frequency and power output, you can do direct comparisons between two antennas under identical propagation conditions.
I’ve already done a couple of comparisons between the AX1 and other commercial antennas. But I think the test I just completed might be of particular interest because it pits the AX1 against an antenna I’ve seen you use many times – a 28.5’ end fed with a 28.5’ counterpoise. I used 24 AWG silicone insulated wire. The end of the radiator was placed on a 19’5” telescoping fishing pole. This is my preferred POTA mast when I can’t use a tall tree.
I spent some time trying to control other variables so that the only significant difference during the test would be the antennas themselves.
For example, the SOTA Beam WSPRLite Classic transmitters don’t have an ATU. So, I had to make the antennas resonant on the 20-meter WSPR frequency of 14.097 MHz. For the AX1, Thomas’ videos helped a lot. I used a clip-on capacitance hat and adjusted the counterpoise to 15’ 2”. This gave me an SWR of 1.17:1. For the end fed, I tried the two UNUN’s I had available and settled on the 49:1, which got me the closest (2.2:1). I then used a manual tuner to achieve an SWR of 1.29:1.
I also wanted to deal with the difference in power output between the two transmitters. Although they’re identical, and both set to 20 milliwatts, there is no way to ensure both are actually producing that output level. Based on tests by NG4S, one of the transmitters runs at 19 milliwatts. The other actually outputs 27 milliwatts. So, my plan was to run the test for 48 hours. At the end of 24 hours, I would switch the transmitters (and callsigns) so that both antennas would benefit (relatively equally) from one of the transmitters being stronger.
At the end of Day 1, I reviewed the data from the two transmitters on dxplorer.net/wspr. The end fed averaged a 5.7 dB gain over the AX1 based on reports from receiving stations that spotted both transmitters in the same 10-minute block (simultaneous spots).
On Day 1, the stronger transmitter was on the end fed. The maps below are from WSPR.rocks.
Many thanks to Terry (N7TB) who sent the following question by email and has kindly agreed to allow me to share it here along with my response on QRPer:
Hi Thomas,
I cannot tell you how much I appreciate your POTA videos and all the suggestions you have made that I have adopted. I look forward to every activation you put on video. […]
[…]I have a question for you about using your AX1, and would really like your advice. I marvel at how quickly you can activate a park even with an AX1 antenna on 5 watts. I also have an AX1 antenna, counterpoise and KX2[…].
Anyway, I was out today activating K-0213, Maude Williamson State Park, about 20 minutes from my QTH in West Salem, OR. I operated 12W into a 33ft. EFHW antenna suspended vertically from a 31 ft. Jackite mast. All my activations are CW; I usually activate 20 meters.[…]
I was able to finally work 22 stations in an hour and a half, mostly in CA, UT, MT, and one in AZ. I did get a contact in KY, AZ NM, and MB, but it was a tough go for them to hear me. Most of my activations take me a bit over an hour to get 20 contacts.
As I thought about how much easier it seems that you are able to activate, I started to think about geography and population density differences between the East and West coasts. I used Google Earth and measured almost all points east of the Mississippi from Asheville and most were within 1200 miles. I would guess 2/3 of the US population live in this area. I drew the same range from my QTH and I get about half way into MT, barely into WY, most but not all UT, just touch the NW corner of AZ, and all of CA. In all but CA, I would guess the population total in this vast area is less than Illinois. That is my dilemma. I would love to be able to go out, setup my AX1 with my KX2 on even 10 watts, and make quick activations, but I would be surprised if I would get many contacts because the distances are so vast in the West and population density so low. I will actually try using the AX1 when the WX gets better and I can sit at a picnic table. So far, I have had little success with it, even deployed with the correct counterpoise. Do you have any thoughts on how to be successful with the AX1 from the West coast for POTA, or should I just concentrate on other antennas?
[…]Thanks again, Thomas, for the emails you have sent me with suggestions about equipment, and for all your great videos.
Very 73,
Terry
N7TB
Hi, Terry,
First of all, thank you so much for the kind words. I really appreciate that!
Regarding your message:
Keep in mind that the day you were operating was a very strange day in terms of propagation. There were times when we were having radio blackouts (especially in the western half of the US) and there were times propagation was amazing, yet very unstable. We were hit by so many heavy CMEs this weekend–one seemingly on top of another.
I think you do have a valid point, though, about the geography–one I try to mention when talking about compromised antennas like the AX1.
QSO Map from my latest AX1 activation.
I realize that I enjoy a lot of success with the AX1 because of where I live. I guarantee that the bulk of the US ham radio population is within easy reach of my AX1 antenna, no matter what band.
For you? There are no hams to your west (within easy reach), extremely few to your north (save WA and BC), and the best ham density is to your south in California.
In your shoes, here’s how/when I’d try using the AX1 (keeping in mind I’ve never operated POTA in the western states):
First, I would focus on using 40 meters when the band is healthy and/or for early morning, late afternoon/evening sessions. That should snag contacts across WA, OR, and CA with the AX1. Might be a stretch for southern CA, but I think you could make that work. The only caveat is that flaring has been wiping out daytime 40 meters a lot lately. You might check band conditions in advance.
I would also consider spending time on 17 meters, and possibly 15 meters with your AX1. This might throw your signal across to the midwest, Ohio Valley, and beyond. 17 and 15 meters isn’t typically as productive as 20 meters (at least, for me) but I routinely log west coast stations on 17 meters with the AX1. 15 meters is also getting a lot of attention in the POTA spots!
A wire antenna is almost always a better option than the AX1 if you have the time and space to put it up, but the AX1 is just so darn convenient.
Cheers, Thomas K4SWL
More suggestions?
The reason I asked Terry for permission to post his question and my reply here on the blog is because I suspect there are west-coasters (and those in similar geographic situations) who may be able to share some helpful strategies.
There are so many factors involved beyond what I mentioned in my reply. In fact, I imagine if the goal is to work parts further east, then adjusting the activation schedule for Central and Eastern time zones might also help (for example, not activating during dinner hours when I always see a bit of a lull in hunter activity).
If you have some experience, please feel free to comment!
As I mentioned in previous posts, I’ve been using the Elecraft AX1 in heavy rotation this year. I made a commitment to myself to do a string of activations with it in January and February and also pair it with a wide variety of radios beyond the Elecraft KX2 and KX3. So far, I’ve paired the AX1 with the:
In truth, the AX1 can be paired with any radio when you use a tripod mount.
It’s a bit trickier when connecting the AX1 directly to a radio and using the Bipod as a support because 1.) the antenna connector on the radio mustn’t be too high off of the surface, 2.) there needs to be enough clearance on the back of the radio to accommodate the bipod legs and 3.) ideally, it’s nice to have a ground point on the radio, else you’ll need to clamp the counterpoise to the shield of the BNC connector.
In addition, if your radio doesn’t have a built-in ATU of some sort, then you’ll also need a capacity hat or external ATU to finish off the impedance match. (For more notes about the AX1 and AX2, check out this previous post.)
Of course, you don’t have to use Elecraft’s bipod to support the AX1 when directly connected to a radio–you can build or 3D print your own support–but the bipod is really convenient when it does work.
Objective: Lunch Box Radio
One radio I’ve been eager to pair with the AX1 is the Penntek TR-45L.
Many thanks to Thomas (DM1TBE / M0KEU) who shares the following SOTA field report he also shared on the excellent SOTA reflector.
How two Scottish SOTA activations encouraged me to upgrade my German license
by Thomas (DM1TBE / M0KEU)
I just wanted to tell someone this story. Not sure if you want to hear it, but I will tell you anyway
During June last year, my boss asked me if I could step in for an ill colleague and visit a business partner in Frankfurt and Edinburgh. As a SOTA activator, I first checked the map and have happily spotted a summit within walking distance of the hotel in Edinburgh.
Unfortunately, there were three issues to solve:
The UK does not accept my German “Klasse E” (CEPT novice/intermediate) license;
operating a radio on the summit requires written permission and
as the duration of the trip was planned with just 2 overnight stays, only hand luggage was possible.
At the Ham Radio in Friedrichshafen, I asked an RSGB representative if it is possible to get a British license as a German. Mark, M1MPA, explained to me how the process worked, so I started the online course provided by GM6DX. It was not too difficult, and I soon passed every mock exam. Roughly, two weeks before the trip, I passed the RSGB operated online exam and got my UK foundation license, so I could operate in Scotland as MM7TBE.
Regarding the issue with the permission to operate on the summit, I first chose to ignore and pretend being a stupid foreign tourist until I was told that it is really enforced, and my activation could be deleted. So, I asked the Ranger Service at Historic Environment Scotland for permission less than two weeks before my activation and received it just one day later with a comment that it is usually expected to ask one month in advance. Many thanks to the Ranger Service, next time I will come earlier – I promise!
The last issue was the size of the equipment.
There is no tree on top of the summit Arthur’s Seat GM/SS-272, and I had very little space left. So I went with a KX3 with an AX1 antenna and a FT2D for 2m FM.
Now the journey could begin.
On the first day, I was at a very high place in Frankfurt but unfortunately, it did not qualify for SOTA. That evening I arrived in Edinburgh.
The next day, late afternoon, the fun could start.
If you recall from my last field report, I’ve been pairing the Elecraft AX1 antenna with a number of radios. For me, it’s been a fun exercise because I always enjoy seeing what sort of results the AX1 might produce. So far, it has never disappointed.
On Thursday, February 2, 2023, I packed two radios in my car with the idea of fitting in two consecutive park activations.
At my first activation of the day–Lake James State Park–I paired the AX1 with my Mission RGO One transceiver. The activation was a blast! Not only did I stay busy working stations, but I also managed a little QRP DX thanks to a hunter from Italy.
K2 and AX1 Under Shelter
Little Guatemala Café
After grabbing a curried chicken salad wrap at Food Matters and a coffee at Little Guatemala roasters in Morganton, I hit my second and final park of the day: Tuttle Educational State Forest (K-4861). It was rainy, so the park was empty which allowed me to take over the very large picnic shelter at Tuttle.
Even though this particular shelter is in a bit of a dip in the land and has a large metal roof, I’ve had successful activations there in the past employing the AX1 antenna.
QRP radios, product announcements, reviews, news and more. Low power amateur radio fun!
Please support QRPer by adding us to your whitelist in your ad blocker. Ads are what helps us stay online. All of our ads are ham radio related--no junk, we promise! Thank you!
