Category Archives: POTA

Field Reports, News, Portable, POTA, QRP, QRPp, Videos

Testing the Ionosphere: A 100 milliwatt to 1 watt POTA Activation During a CME? Why not!?

6 Comments

Sometimes, I like the odd “exercise in futility.”

I enjoy shaking up routine and since POTA and SOTA activations are my routine, they end up being the shakers.

On Monday, September 18, 2023, I found out that our planet was rotating into a large CME (Coronal Mass Ejection). This CME made all of the space weather news and we planned for either some potential radio blackouts or at least very unstable conditions.

As I’ve said many times before, I never let the potential for poor propagation stop me from hitting the field. Don’t let it stop you either.

Lake Norman State Park (K-2740)

I had a full afternoon to play radio, so I made my way to Lake Norman State Park.

En route, I tried to think of a way to shake up the activation a bit. I planned to activate at the same spot I had during my last visit because I knew the park’s main trail system was still closed and, frankly, I wanted to take advantage of the EV charger at the visitor’s center again!

I’d packed MW0SAW’s End-Fed Half-Wave (the gift that keeps on giving, Steve) and I did have one new radio toy (more on that later).

I also had a lot of time–at least, more than I normally do during a POTA activation–so I thought it might be fun taking my KX2 down to the lowest power setting it has: 100 milliwatts.

I’ve activated parks with 100mw before, but never intentionally on a day when I knew propagation would be poor.

I figured with enough time, maybe I would get the ten contacts needed for a valid POTA activation.

If not, it would be fun trying!

Why Milliwatting?

At the end of the day, I think taking our radios and antennas to their low-power extremes gives us a taste of what we can actually do with so little signal.

I remember shortly after I bought my first Elecraft KX1 in 2008, I was speaking with a local ham and he told me that a maximum output of three watts was pretty useless and that I really needed a minimum of five watts if I expected to make any contacts.

Part of me did feel like perhaps I’d bought something more akin to a toy–fun to look at and hold, but not terribly practical.

Then I started using that KX1 to make contacts and even carry on extended rag chews. Turns out, three watts gets a lot done!

Today, I’ll often run my MTR-3B with three watts or even less when activating a summit and the results are simply outstanding–fabulous DX and contacts galore.

I know 100mw is a proper compromise, but I like knowing what I can achieve with so little. Tinkering with it in the field and listening to signal reports (also reading RBN stats) gives me a good idea.

In an emergency situation? If I could only push 100mw into a decent antenna, I know it wouldn’t be ideal, but I know it wouldn’t be futile either.

Begali Adventure Dual

Another activation motivation was the opportunity to test my new-to-me Begali Adventure Dual paddles. Continue reading Testing the Ionosphere: A 100 milliwatt to 1 watt POTA Activation During a CME? Why not!? →

Articles, Field Reports, News, Portable, POTA, QRP, SOTA, Travel

A Recap of the 2023 W4 SOTA Fall Campout

13 Comments

Another W4 SOTA Fall Campout is in the books! What amazing fun.

This year, the campout was held at Lake Rabun Beach Recreation Area in north Georgia.

Once again, Joshua (N5FY), and I shared a campsite. He arrived Wednesday afternoon and I showed up Thursday afternoon around 2:30 PM.

There was quite a lot of wet weather in the forecast, so I opted to bring my large 6 person tent (the orange one above) instead of my two person ultralight tent. My thinking was that, if need be, we could us the large vestibule on this tent as shelter while eating and cooking.

Joshua was way ahead of me, though, and brought a canopy for the picnic table.

After pitching my tent and setting up, Joshua and I discussed how we should spend the rest of the afternoon. One thought was to try to squeeze in a SOTA activation, but we would have been fighting sunset at the end of it.

Instead, Joshua suggested that we build some antennas.

It was then I noticed that Joshua’s picnic table canopy had a built-in spool of 26 gauge wire!

I shouldn’t have been surprised. Joshua is the fellow behind the Tufteln brand of antennas. Turns out, he brought along a full antenna-building station.

I built a long random wire antenna and started a 30M EFHW.

That evening, we had friends pop by the campsite, ate dinner and fit in a quick POTA activation.

We didn’t have to drive to the activation site because our campground was in the Chattahoochee-Oconee National Forest (K-4473). Continue reading A Recap of the 2023 W4 SOTA Fall Campout →

Field Radio Kits, News, Portable, POTA, QRO

Field Radio Kit Gallery: VA7EKA’s Yaesu FT-857D Field Kit

11 Comments

Many thanks to Andrew (VA7EKA) who shares the following article about his portable field radio kit which will be featured on our Field Kit Gallery page.

You may note that this isn’t a QRP radio, but the FT-857D will run QRP power! If you would like to share your field kit with the QRPer community, read this post. Check out Andrew’s field kit below:

Yaesu FT-857D off-grid portable kit

Andrew (VA7EKA)

As part of my amateur radio operations, I’ve quickly seen the advantage of having a small, portable radio I can operate anywhere and deploy quickly. Especially as I don’t have a permanent HF antenna installation at home, being able to set up in the yard (or even indoors) in a pinch is pretty high on the list of requirements for me.

I started reading online and watching videos about this topic, and found an excellent video from KT7RUN “The Tech Prepper” (and an earlier one) which showed a super-slick portable radio setup featuring the Yaesu FT-857D. Prior to finding those videos, I had already acquired an FT-857D due to its all-band, all-mode operation and compact size, and Gaston KT7RUN’s kit seemed like a very compelling setup for this radio.

Here’s what I’ve ended up with for my off-grid-capable “grab’n’go” radio station:

Inventory

Currently this is the inventory for this kit:

Antenna options:

and for charging this station in the field…

Details

Of course, the core of this kit is the radio. It’s popular for a reason. All-band, all-mode “shack in a box” in a truly portable form factor. Capable of 100w operation, it’s more than enough to make whatever contacts you need. In my case, because the battery has a max 20A continuous-discharge specification, I wouldn’t actually transmit at a full 100w with this exact configuration. Not a problem – I’m not expecting to transmit at those levels with a pack of this size.

The pack frame is truly solid, though it adds a good amount of weight (1.364lbs with all options). It’s absolutely worth it though. Not only does it provide rigidity and protection, it also provides convenient mount points for attachments, like the relocated antenna connections and Digirig holster. I could securely attach additional items if needed.

The battery just fits into the MOLLE pouch which is pretty lucky. I got a small PowerPole distribution block so I can not only connect the radio to the battery, but also the Genasun solar charge controller and whatever other power-related accessories I might use (e.g. Dakota Lithium’s 5v USB charger which I’ve adapted to PowerPole). Solar-wise, the charge controller I went with has a little more capacity than what I’m using currently with the 75w panel. I figured I should bump up to the 10amp charge controller to allow for a larger solar panel later on.

For CW operation I’ve relocated the jack with a basic 3.5mm audio extension cable going up through the bag and looped through the PALS webbing on the High Ground Gear PRC-117G bag. For a key I’m usually packing a basic 3d-printed iambic paddle I got at a swap meet for $20. I’d love a N0SA SP4 paddle but… $$$ :‘D

In the following photos you can see how I’ve laid out the relocation cables. I specifically took photos of these to show people who want to re-create this kit, because it was pretty tedious to get it all in there. Hopefully these will save someone a bit of time. 😉

All in all, this kit weighs in at 11 pounds. It’s a bit heavy to carry for a SOTA activation, but for POTA it’s no problem at all. I have indeed carried it up to a SOTA summit, but HF propagation conditions were poor and I was really struggling to make any contacts. Ended up resorting to activating on 2m with a tape measure Yagi. 😉

Because of the PALS webbing on the PRC-117G bag, this portable kit could be strapped to a larger backpack as needed, though typically I have just carried the kit inside my backpack, to keep the weight closer to my body. Perhaps more notably, additional accessory pouches could be attached, like a pouch for logbook/pencil/antennas/CW key etc.

Conclusion

So how is this kit to actually use? In a word, awesome. Drop it on the ground or on a table, deploy and attach an antenna, turn on the power. If I’m expecting to be on air for a long time, I can attach the solar charge controller and solar panel to keep the station running (though I have yet to do this while operating, since I completed this kit very recently). I can go out into the field and use this setup indefinitely, regardless of available electrical infrastructure.

For digital operations, I have a ToughBook CF-31 which is fully configured with all relevant software I’d typically use. This is great for tossing in the vehicle for a POTA activation, and even feasible for SOTA if you’re in great shape or willing to carry the extra weight. An alternative for digital ops could be a lightweight single-board-computer, tablet, or netbook, of course.

Just for fun, here’s a map of most of the QSOs I’ve made with this rig since putting it together. It’s not exhaustive, but what I could quickly gather up for this post. 133 contacts across 11 countries. The furthest contact thus far is with VK2WN on 30m FT8, at a nice 11965km (7435mi) distance, with just 5watts of output power on my side. Nice!

If you have any questions about this kit or would like additional details, please feel free to reach out. I’d also be curious to hear from anyone who follows this build and creates their own variation!

73 de VA7EKA

Antennas, Field Reports, News, Portable, POTA, QRP, Stealth, Videos

A Trailside, Low-Impact, Knee Board POTA activation at the Carl Sandburg National Historic Site!

9 Comments

On Friday, September 15, 2023, my wife and I had a few hours midday to enjoy the gorgeous pre-fall weather, so we decided to go on a hike with Hazel.

My wife was the one that suggested I pick out a hike that would open the door to a short POTA activation (isn’t she the best–?).

Carl Sandburg National Historic Site (K-0804)

Earlier that week, I made a note to activate the Carl Sandburg National Historic Site in the village of Flat Rock, North Carolina. I passed this idea by my wife and she agreed that it’d make for a perfect outing.

The mission of the Carl Sandburg National Historic Site is to preserve Connemara, the home of Pulitzer Prize-winning poet and writer Carl Sandburg.

The park has a wonderful trail network and I hadn’t visited it since 2016, during the National Parks On The Air (NPOTA) ARRL event.

Technically, I could go back into my NPOTA logs and upload my Sandburg activations to the POTA site because previous activations do count, but I’m not actually motivated by my park count so much as I am just having fun working new-to-me sites under the new POTA program.

That said, my somewhat flexible, non-committal goal of having at least 100 unique parks activated for POTA before the end of 2023 was also on my mind; a small motivator to expand my POTA footprint.

Admittedly, there really aren’t many parks that are within two hours of my QTH that I haven’t already activated for POTA. The ones left, like Sandburg, are just outside the corridors I normally travel.

The Sandburg site is a beautiful one, and I think Hazel may have even remembered this spot from so many years ago. My wife and I got a kick out of how giddy she was to hit the trails, smell the smells, and meet all of the other hikers.

Hazel: “Enough talking, Dad! More hiking!”

Time to hit the trails and find an activation spot!

Knee Board Portable!

Back in 2016, I got permission from a Sandburg park ranger to place a wire in a tree in order to perform my NPOTA activation. She only asked that I perform my activation on the trail network (not at the house and goat farm).

Wow…I just checked and I had forgotten that I made a short field report of that activation over on (my other blog) the SWLing Post—check it out here.  Back then, my KX2 was still very new and shiny!

Not even a scratch on the KX2 back then! Today, Hedy looks a little more field battered! 🙂

And here we are seven years later and I’m still activating the Carl Sandburg site from my lap. This time, however, I don’t have my radio on a clip board, I’m using a folding knee board:

This is my Tufteln/N0RNM folding knee board and you’ve seen me use it in numerous activation videos.

Instead of just placing my logs and radio on the knee board, like I did back in 2016, I wanted to place my entire antenna system on it, too.

You see, although I’m sure the staff at the Sandburg home wouldn’t mind me putting a wire in their trees along the hiking trail, I couldn’t find a staff member to ask, so I used this as an excuse to try something I’ve always wanted to do: mount my AX1 on the knee board as well!

We found a park bench a mile up the trail and decided to set up there. Continue reading A Trailside, Low-Impact, Knee Board POTA activation at the Carl Sandburg National Historic Site! →

Field Reports, News, Portable, POTA, QRP, QRP Radios, QRPp, Reviews, Videos

Getting To Know You Series: The Elecraft KX3–My thoughts, notes, and one extreme QRPp contact!

16 Comments

I’m very fortunate in that in the past few years I’ve accumulated a number of QRP radios that I use in rotation when I do park and summit activations.

I’m often asked for advice on choosing radios, and as I’ve mentioned in the past, I feel like the decision is a very personal one–everything is based on an operator’s own particular preferences.

Over the years, I’ve written formal reviews about most of the field radios in my collection. In those reviews, I try to take a wide angle view of a radio–to see how it might appeal to a number of types of operators. I highlight the pros and cons, but I don’t focus on my own particular take because, again, my style of operating might not match that of readers. I try to present the full picture as clearly as I can and let the reader decide.

The Getting To Know You series gives me an opportunity to highlight one radio at a time and showcase what I love about it and why it’s a part of my permanent radio collection. After we spend a bit of time talking about the radio, we’ll do a park or summit activation with it!

The Elecraft KX3

I was originally introduced to the Elecraft KX3 at the 2011 Dayton Hamvention–over a decade ago at time of posting!

I was commissioned to write a review of the KX3 for the Monitoring Times Magazine and Elecraft was kind enough to lend me a brand new KX3.

At the time, there was nothing like the KX3 on the market and I felt like I’d just received a radio from the future.

The KX3 offered 160-6 meter general coverage with an optional 2 meter module, ATU, internal AA battery compartment, and roofing filters. The controls were top mounted and current draw in receive was as little as 150 mA. At the time, there was no other radio on the market that could compare with the KX3’s field prowess.

But it wasn’t just its field design that was impressive.

In fact, when Rob Sherwood tested the KX3, it placed at the top of his list which is sorted by Third-Order Dynamic Range Narrow Spaced.

This field radio sported a bullet-proof front end and true contest chops, displacing $10,000+ high-end rigs.

Today, the KX3 (at time of posting) is still number 12 on Rob’s list. An impressive feat!

Herein lies the danger of doing reviews…

I didn’t have the KX3 in my grubby little hands for more than a few hours when I decided I had to buy one. I sold some gear to free up money and I bought the KX3 Elecraft sent me on loan for the full price.

I’ve taken this KX3 on numerous activations and on international travels. It’s a brilliant QRP companion.

These days, it’s in the shack more than in the field because I keep it hooked up to my KXPA100 amplifier. I feel like the KX3/KXPA100 combo is like having a poor man’s K3. As a huge bonus, the KX3 takes up little space on my table and the KXPA100 sits on a shelf–the overall footprint is much smaller than a K3 or K3s. It’s like having a remote head on my desk and works perfectly for my limited space shack.

The KX3 is a stellar, benchmark field radio, so it was great fun to feature it in this video.

Zebulon B. Vance Birthplace (K-6856)

For this Getting To Know You report and video, I decided to activate one of my favorite local parks on September 12, 2023: the Vance Birthplace. Continue reading Getting To Know You Series: The Elecraft KX3–My thoughts, notes, and one extreme QRPp contact! →

Field Reports, Guest Posts, News, Portable, POTA, QRP

Matt’s “Crackadawn POTA” Field Report

4 Comments

Many thanks to Matt (W6CSN) who shares the following post  from his blog at W6CSN.Blog:

Crackadawn POTA

by Matt (W6CSN)

This is the weekend in October that features the U.S. Navy’s Blue Angels taking to the skies over the Bay Area. The air show takes place over the Bay waters, which means the beaches and shorelines around San Francisco will be packed with people and traffic. Since my usual POTA operating location is right by East Beach, I had pretty much given up on the idea of activating K-7889 this weekend.

Lights of the Golden Gate Bridge reflecting off the still Bay waters.

The airshow is on Saturday and Sunday, but the Blue Angles practice on Thursday and Friday, weather permitting. So here I was on Friday morning, awake at 5AM watching K4SWL on YouTube doing POTA when the idea of getting out for an early activation got into my head.

It was still dark when I tossed my backpack, which was already loaded for POTA from the previous activation, into the car and headed down to the East Beach in the Presidio of San Francisco National Historic Site (K-7889).

The sky getting lighter in the East before sunrise.

Given the early hour and low light conditions I didn’t relish the idea of doing my usual picnic table and tripod antenna setup. Not long ago I had acquired one of those “mirror” antenna mounts with the jaw clamp arrangement, and this was a great opportunity to try it out. Between the parking lot and the beachfront promenade there is low fence constructed of short steel posts and strands of stainless cable. The fence post was a perfect place to attach the clamp and the MFJ-1979 17 foot telescopic whip, which is a quarter wave on 14 MHz.

Close up of the MFJ-1979 whip antenna clamped to steel fencing.

I was ready to string some radials out to give the antenna a ground plane to work against, but wondered if the post, being sunk into the ground by the Bay and the steel fencing cables might provide enough of a counterpoise. A quick check of the SWR on the meter built into the MTR-4B showed a 1.2 to 1 – no need to even bother with radials with an SWR like that right out of the box.

Low SWR on the quarter wave vertical as the Bay wakes up.

The other advantage of this antenna setup was that it is right next to the car. However, I don’t really like operating from my vehicle as it’s not very sporting nor is it comfortable. Instead, I simply set the station on the trunk lid and completed the activation from a standing position. The other advantage of this arrangement was that I could closely guard the RG-316 coax going from the radio to the antenna to keep any humans or canines from getting entangled. Continue reading Matt’s “Crackadawn POTA” Field Report →

Field Reports, News, Portable, POTA, QRP, Videos

POTA at Lake Norman: Beautiful day for a TR-45L trailside activation (and hunting VE6LK)!

6 Comments

I’m getting used to having an electric vehicle for my weekly travels including POTA and SOTA excursions.

My Volvo C40 has a published range of about 226 miles on a 90% charge, but I find that I actually get more than that. I almost never need to recharge from a public charger–I just plug it in at home.

At least once a week, I visit my parents in Hickory, NC and that round trip (including errand running in town) logs a good +/- 200 miles. By the time I return to the QTH, I typically have a comfortable 20% charge left on the battery.

Many of the parks I activate in that travel corridor are 20-30 minute detours off of Interstate 40 (for example: Lake James SP, South Mountains SP, Tuttle Educational SF). They have no negative impact on my ability to make it back to the QTH with battery capacity to spare.

Parks, however, that are still close to Hickory, but in the opposite direction of home, may necessitate a quick charge at one of the many public charging stations along the road. Not a big deal, but it’s kind of fun when I can do a full trip on one charge.

Flag at half staff in memory of September 11, 2021

On Monday, September 11, 2023, I had a full afternoon open and really wanted to fit in a proper hike. One of my favorite easy six mile loop trails–the Lakeshore Trail– is at Lake Norman State Park.

Lake Norman, however, is in the opposite direction of the QTH and is about an 80 minute round trip. I fit in errands along the way, but going there means I’ll need a bit of a charge to get back home the following day.

After a little research, though, I discovered that Lake Norman (much like Lake James) has free EV charging at their visitor’s center! Woo hoo!

Lake Norman State Park (K-2740)

I arrived at the park in the early afternoon and–whew!–both of the EV charging stations were free. In fact, the visitors’ center parking lot was almost empty–I would have expected a few more cars. I found that curious.

I plugged in my car, put on my hiking boots, grabbed my hiking sticks, then made my way to the spur trail that connects the visitors’ center parking lot to the Lakeshore loop.

Only, when I reached the trailhead, there was a notice stating that all of the trails were temporarily closed. Wait…what?

This may explain the lack of visitors.

I was bummed to say the least. My backup plan would be to hike the road at Lake Norman, but that’s not nearly as fun as a proper trail.

I then walked to the visitors’ center and asked the staff inside about the trail closures. They pointed out that there was one small loop trail–next to the visitors’ center–that was still open.

I was pleased to hear that and decided that instead of hiking one long loop, I could simply hike the same small loop several times.

I thanked them then gave them a donation (which I was going to do anyway) especially since I was getting free EV charge!

I walked out the side entrance of the building and onto the Alder Trail.It was a very nice little loop trail and long enough that I didn’t feel like I was walking in circles. Continue reading POTA at Lake Norman: Beautiful day for a TR-45L trailside activation (and hunting VE6LK)! →

Field Radio Kits, Guest Posts, News, Portable, POTA, QRP, SOTA

Field Kit Gallery: NL5E’s Lightweight KX2 SOTA/POTA Alaska Backpacking Radio Kit

9 Comments

Many thanks to Eric (NL5E) who shares the following article about his portable field radio kit which will be featured on our Field Kit Gallery page. If you would like to share your field kit with the QRPer community, read this post. Check out Eric’s field kit:

NL5E SOTA/POTA Backpacking Kit

Description

Hello! NL5E here.

I’m one of the rare SOTA activators in Alaska (I also use this same kit for POTA). Anyone that has looked at a map of this state will know that we have some interesting difficult topography. Many of our summit hikes start out near sea level, but are 3000-6000 vertical feet of climbing to get to the summit. So I built my kit with compactness, versatility, and weight in mind. Everything weighs approximately 2lbs (not including the battery, I don’t always take it).

My primary operating modes are CW, FT8, and SSB.

To facilitate those modes I tried to keep everything as small as possible while still being usable. For example, I debated using N6ARA’s tiny paddle, but I found I made too many sending errors. The N0SA paddle is a perfect medium between portability and sending ability. For FT8 the FT8CN app has been a good alternative to carrying a Raspberry Pi or small laptop and the well loved Digirig is probably the best audio/cat interface on the market today. I don’t do a lot of SSB (especially at QRP levels), but the K6ARK mini microphone is a wonderful improvement over Elecraft’s comically massive microphone for the KX2. I added headphones so I don’t disturb anyone on popular summits and so I can hear CW a bit better.

My antennas of choice tend to be random wires and End Fed Halfwaves.

With the KX2 I chose to use K6ARK’s 20w antenna kits and built both a 9:1 and 49:1 version. I usually carry the 9:1 just to have the band flexibility as it will work from 40m-10m. If the ground is wet enough I’ve had it tune up to 80m.

For the 49:1 I chose 20m because bands lower than that have mediocre performance from the latitude. Because of how short both these antennas are, they pair very well with the SOTAbeams Carbon 6 mast. From a summit a 19’ mast is usually tall enough to work most of the US and lots of Asia from here. The only modification I made is gluing the top 2 sections together for durability. To attach the antenna wire I use a small Niteize carabiner and a prussik loop.

I also wanted to ensure that I could power many different devices while out hiking. I settled on an Anker battery because it is easy to power phones and the radio without having to bring a bunch of different adapters like I would with a dedicated 12V battery.

I know someone will mention protection and the bag I chose. Yep, a silnylon stuff sack offers zero protection from bumps and impacts. I firmly believe that hams “over baby” their equipment and think that their radios will hilariously explode if sneezed on wrong. I settled on the Gems Products cover and rails as a good solution to keep the radio from getting destroyed in a backpack. So far so good. I added the dry bag to my list for rainy days.

I didn’t include one in the images, but I also usually have an HT with me, but most summits don’t have good line of sight to our population centers. I usually run a Yaesu VX-6R with Diamond RH77CA or MFJ Longranger. I will usually run 2m FM when I am close to Anchorage or Palmer. I also didn’t include my logging solution, but that is usually HAMRS on my iPhone or a Rite in the Rain book and pencil. I find CW is easier to log on paper for some reason.

Thanks for looking and perhaps I’ll hear some of you on the air.

Component List

Radio: Elecraft KX2 with Side KX Heatsink and Cover

Antenna: K6ARK Random Wire with 29’ of polystealth wire and antenna winder

Note: I also run a 49:1 EFHW cut for 20m (not pictured, looks the same).

Dog: Luna. Standard issue Alaska Husky. Smol in size. Adds 5 dB gain to all antennas. Adds 45 lbs, but is self transporting.

Support: SOTAbeams Carbon 6

CW Paddles: CW Morse N0SA SP4 Paddle

Microphone: K6ARK mini microphone with printed case. Built from Digikey Parts.

Headphones: Sony Earbuds – could be any old ear buds. These work fine.

Digirig Mobile with Cables: Lets face it. Sometimes FT8 is all that works. I’m in Alaska.

Android Phone: Galaxy S10. Dealers choice for a phone. It exists only to run FT8CN instead of carrying a laptop for FT8.

Power: 

–JacobsParts 15V 5A USB C PD cable 5.5×2.5mm DC (Ferrite Added)

Note: Outputs approx. 14.5V when measured using my multimeter. Radio shows the same/

–Anker 747 25600mAh battery

Miscellaneous Items:

–5.5×2.5mm to 4.0×1.7mm DC Adapter: Allows charging of various HT radios using the Anker battery with JacobsParts USB C cable

-Shower Cap: The all important rain cover for the KX2. Just in case. Just make sure it is transparent.

Storage: Sea to Summit 3L UltraSil Stuff Sack or Sea to Summit 3L Dry Bag

Articles, Field Radio Kits, Guest Posts, News, Portable, POTA, QRP, QRP Radios

Field Kit Gallery: W4EMB’s Penntek TR-45L Portable Kit

14 Comments

Many thanks to Ed (W4EMB) who shares the following article about his portable field radio kit which will be featured on our Field Kit Gallery page. If you would like to share your field kit with the QRPer community, check out this post. Ed writes:

My QRP Portable Set up

by Ed (W4EMB)

Radio: I have one priority rig I use 99% of my time. It is the TR45L Penntek. I have both versions. The fullsize one with built-in tuner and battery, I also have the “Skinny” version. The skinny does not have the tuner nor battery. My second Rig is the Yaesu 817 with the Windcamp Battery upgrade. I also have a 40m only QSX and the 5 band TruSdx.

Penntek TR45L Skinny with external batter and external tuner.

Antenna:  I use the Chelegance MC-750 most of the time, but also use a Homebrew EFHW with 49:1 balun and 67’ of wire.

I have the QRP guys Tri-Band vertical kit, and two pieces of 16ga Speaker wire cut to 33’ that I carry as well. To support the EFHW and Speaker wire antenna, I use the SOTABEAMS 10m (32 ft) “Travel Mast”.

For the QRP Guys Tri-band vertical, I use the SOTABEAMS Carbon-6 ultra light 6m (19.6 ft) mast. To support the 32’ mast I usually just lean it into the trees and slope my EFHW up from the feed point.

For the speaker wire antenna, I run the “red wire” straight up the mast while it is strapped to the picnic table. The “black wire” is simply thrown out across the ground. I might even elevate the black wire with sticks.

My carbon-6 fits right into a piece of 1 ¼ inch PVC pipe I have clamped to my brush guard on my van. Or, I use a Tiki-Torch stake to hold my carbon-6 in open ground.

carbon-6 with Tiki-Torch stake supporting and using the Tri-band Vertical.
carbon-6 inside of PVC pipe with the QRP Guys Tri-band vertical.

I find for me, that my QRP Guys antenna works great on 20m without a tuner. But when I try to use it on 30m or 40m, I require a tuner. For this reason, I lean on my MC-750 to be the main antenna.

I have modified my MC-750 slightly. I made my own set of radials to match the factory ones. I chose to make them out of silicone wire. I find it to be more flexible and does not kink or tangle as easy as the standard factory radials. I used 3mm banana plugs and 24ga yellow wire. I also crimped small ring connectors onto the ends of the radials. I did NOT strip the insulation and place them on the wire. I simply crimped them on the silicone. I use them to stake down the wire. I use four nails as “stakes” to pin the wire down. I find I only stake the radials out when I am on un-even ground.

The second modification, I made a set of “double” radials out of 26ga green silicone wire. Colors do not matter. It is what I had. I spread them evenly around the base of the MC-750.

MC-750 with “double radials” and RG316 for coax.

My key is a Czech military straight key from the 1950s. It was new old stock when I bought it. I also carry a small mini set of paddles. For the TR45L radio, I can not play my recoded CQ or 73 with out a paddle. The “play” button is dit or dah trough the paddle jack.

For coax, I use RG316 and the appropriate adapter for the MC-750.

I have two pencils from Kuru Toga. One pencil is .5mm the other is .7mm. I make my own POTA log sheets and I paper log, and then type them later. I am a not talented enough yet to play with a tablet or PC while operating. I have only done CW for the last 12 months.

On my table: I have a really thin yoga mat. I find the concrete picnic tables a bit rough on my equipment. The yoga mat can get a bit sticky when it is warm, so I drape a small hand towel over the edge where my arms lay. I also have a Write in the Rain tablet in full size paper. I have been out early in the mornings in this summer and humidity and steamy fog makes normal paper hard to write on. The .7mm pencil matches up well with the Write in the Rain paper.

Chelegance antenna pictured in the background. K-2965 Paris Landing State Park

I have found CW and POTA have re-energized my ham radio hobby and resurrected it from a dusty shack, to a fun out door activity.

My first challenge was how to get from the car to the table in one trip. Downsize to the necessities. Next was figuring out the antenna and radio combo that could work in different conditions. By conditions I mean space.

Location, location….. I had a dog run between me and my antenna. It pulled my radio right off the table and tumble behind the dog. So now I choose my locations like Bill Hickock… always face the door. Hihi. Food for thought.

Thank you to Thomas for inspiring me to get out there and do it. His you tube videos were great copy practice to give me the confidence to get out there. Finally, my Elmer. John, KM6NN. Without him I would have never started my CW journey. He is a true Elmer in every definition of the word. I am proud to know him and lucky he is in my life. Thank you John.

Gear:

Note: Check out W4EMB on YouTube as he makes his 1st POTA “Kilo” 

Field Reports, News, Portable, POTA, QRP, Videos

Out Of My Element: An Urban POTA activation at the Thomas Wolfe Memorial

8 Comments

It’s funny, but until September 7, 2023, I had never activated one of the closest POTA sites to my home: the Thomas Wolfe Memorial (K-6853).

I remember back in 2020 when I really kicked my POTA activations into high gear, I made a spreadsheet of all of the POTA sites within a 2 hour drive of the QTH and started activating them one by one.

At the time, almost 50-60%, or possibly more, had never been activated. Keep in mind that in early 2020, POTA had a wee fraction of the activity it has today.

It was a lot of fun especially considering those were the early days of the pandemic and it was just nice to get out and about. Any excuse, right?

The Thomas Wolfe Memorial is on North Market Street in Asheville, NC.

One of the parks on my list was the Thomas Wolfe Memorial but being a small historic site in an urban setting, they were closed for quite some time during the pandemic. There was nothing to stop me from walking on the site–or pulling up in their parking lot–and doing an activation while they were closed, but I just didn’t feel like it should be fair game when closed.

Then restrictions loosened up and, frankly, I just sort of forgot about it.

I tend to activate parks in rural areas and I am prone to overlook urban sites (although quite a few of my activations in Canada last year were urban).

Thomas Wolfe Memorial (K-6853)

On Thursday, September 7, 2023, I dropped off my daughters at school then made my way to a doctor’s appointment. I arrived at the office, gave them my name at the front desk, and then they reminded me that we had re-scheduled this particular appointment for later in the month.

Doh! I forgot to make the change in my calendar.

All of the sudden, I had a bit more free time!

Of course, I always fill free time with POTA activations, and I already had radio gear in the car, so it was only a matter of deciding where to go.

I called the Vance Historic Birthplace (about a 25 minute drive) to see if they were busy. Their director (who I know quite well at this point) told me that a large group was on the site, but would be gone by 1:30. That timing didn’t work for me, so I consulted the POTA map.

Since the POTA site used my coordinates to find the closest park, I was reminded that K-6853 was a mere 3 minute drive from the doctor’s office. I could have walked there.

I gave the site a call to ask for permission (again, I always do this for small historic sites) and they told me I’d be most welcome.

The site is on a small urban lot and consists of two buildings: the visitors’ center, and the Old Kentucky Home boarding house. Continue reading Out Of My Element: An Urban POTA activation at the Thomas Wolfe Memorial →

QRP radios, product announcements, reviews, news and more. Low power amateur radio fun!