Category Archives: Guest Posts

Digital Modes, Field Radio Kits, Guest Posts, News, Portable, POTA, QRP

Field Radio Kit Gallery: KI7URL’s (tr)USDx Ultralight Portable Kit

3 Comments

Many thanks to Jim (KI7URL) who shares the following article about his portable field radio kit which will be featured on our Field Kit Gallery page. If you would like to share your field kit with the QRPer community, read this post. Jim writes:

(tr)USDx Ultralight Portable Kit

by Jim (KI7URL)

I like to take amateur radio with me wherever I go. In my backpack, I keep a Yaesu FT-60 (powered by 18650 batteries, but that is a different discussion). But I do not like to limit myself to VHF/UHF.

My wife, on the other hand, does not think my “go bag” should take up a significant portion of our suitcase when we travel. I did build a slimmed-down go kit with my Yaesu 891, but that was still north of 12 pounds (vetoed by Wife). Then, I made a go kit with my Yaesu 818, but that was still near the 10-pound zone (again, vetoed). I needed a slimmer package.

I turned to the likes of the QCX mini or other CW-only radios. The problem is that I still am far from proficient with my code, so relying only on CW was a bit more frustrating than I wanted it to be. The (tr)USDx, an open-source radio about the size of two stacked decks of cards, interested me in both price point and functionality. It has SSB, CW, and digital capabilities….on five different bands! Once it was in my hands, I had to build a kit around this new radio!

I want to keep my radio protected, so I started with a small dry box. On the inside, I printed a ‘redneck laminated’ (see also: packing taped) a quick setup guide for using the radio on digital modes if I ever have an in-field case of “the dumb.”

The radio is powered by a small RC battery. I chose this for size, weight, and availability (had it lying around from another project). When fully charged, it reads 12.6 volts. I added powerpole connectors to it because who does love powerpoles (be careful not to short the battery when adding power poles)? I have a small power adapter that goes from powerpoles to the 1.3mm connector so I can use my bench supply or other power sources without making another cable.

I have two antennas that I use (a K6ARK end fed and a QRP Guys No-Tune end fed with 26 gauge wire for 20m). But I like the QRP Guys one because I mostly do 20m and I think it was slightly lighter than the K6ARK antenna (don’t quote me on that though, I loaned the K6ARK one out and have not gotten it back). Plus, not having a tuner lightens my load as well!

Deployed for digital modes.

I have a retired smartphone in my kit that I use for some logging and some other ham-related apps, but mostly for FT8 using the FT8CN app. I also have WoAD on there and soon I hope I can get WinLink functionality with a small TNC as per this video by OH8STN. HF WinLink would be a good benefit with a lighter load than packing in a laptop or Raspberry Pi.

The kit weighs in at 2 pounds 6 ounces (just over a kilogram). This could be stripped down if I only did an SSB, Digital, or, gasp, a CW activation. But as it stands, the small form factor and low weight make the wife happy!

73,
Jim
KI7URL

Equipment:

Events, Guest Posts, News, Portable, QRP, SOTA

The Arizona 10-Point Madness Summit-to-Summit Event

9 Comments

The Arizona 10-Point Madness Summit-to-Summit Event

by Charlie Brown (NJ7V)

“How can I accumulate a bunch of summit-to-summit points all at once, for Summits on the Air?”  This was a question Pete Scola WA7JTM had been pondering for years.  He initially thought it might be fun to choose several 10-point summits that were near each other, have a person operate on each summit, and then rotate to a new summit every so often.  Eventually, this idea gave way to the Arizona 10-Point Madness Summit to Summit event.  With an invitation from Pete, all willing SOTA participants gathered on a 10-point summit on September 19th, 2018, and 10-Point Madness was born!

The Arizona 10-Point Madness Summit to Summit event is a casual on-air gathering, where Summits on the Air participants set up their ham radio station on the top of summit . . .  at approximately the same time.  Operators are on simultaneously so that there is an overwhelming availability of summit-to-summit contacts to be made.  This event occurs every year on the first Saturday of October.

Fred (N7PN) 2023 10-Point Madness

There was a focus on 2-meter contacts the first year we did this.  We learned quickly during the 2018 inaugural event that it was true madness for 31 ham radio stations to contact 26 nearby summits all at the same time, especially on 2 meters.  We tried alternate 2-meter frequencies and even considered a net control operator.  However, in the end, we learned to just wait patiently for our turn to call for contacts on 2-meters, or if it was extra busy, we just moved off to HF for a while and returned later.  As a courtesy, we now monitor 2 meters and return to it throughout the event to give the operators a chance to come and go.

Adam (K6ARK) 2022 10-Point Madness

That first year was amazing.

We collectively made 1104 contacts, 354 of which were VHF.  And yes, we scored a lot of summit-to-summit points.  We averaged 140 points each, with a grand total of 4324 s2s points for all the Arizona stations.  We announced the event to several online platforms and invited others to participate, and had a few people join us from outside of Arizona. All of them had fun and saw good results as well.

Our 6th annual event concluded a few weeks ago.  Participation has been steady in Arizona but we have seen an increase outside of Arizona.  We had about the same number of Arizona participants as years past, but total contacts increased to 1403.  The average s2s points per participant increased to 169, with a grand total of 4906 s2s points.  I was amazed that Keith KR7RK earned 400 s2s points this year for this event – a new record, I think.  These are only numbers for Arizona participants.

I read on social media that Josh WU7H, who was participating from Washington state, had 55 total s2s contacts and only a fourth of them were from Arizona.  We received some statistics from stations in Georgia, South Carolina, Wisconsin, Texas, Nevada, Washington, Oregon and more.  It is a lot of effort to compile the statistics but it would be interesting to include people outside of Arizona in the future.

Joe (KE9AJ) 2022 10-Point Madness

Here are a few things that have stood out to me over the past 5 years for this event:

In 2019, Josh WU7H and DJ WW7D participated from Washington.  They won the award for most challenging activation in my opinion, operating from a snow packed summit in below freezing temperatures.  But that didn’t deter them!  They continue to come back year after year.  They are tough!

In 2022 my friend Adam K6ARK was participating on a summit in California.  I was able to make a 2-meter CW and SSB contact with him from my summit, 327 miles away.

Several others in Arizona also made contact with him.  While not record breaking, this is long haul for 2-meters.  And this year, I was able to make 19 DX contacts with one summit-to-summit into Germany.  It seems like there are a lot of DX contacts to be made every year, but this was a record for me.

Finally, this year Pete WA7JTM made a contact on every single band from 1296 MHz down to 1.8 MHz.  That’s 16 different bands.  How amazing is that?

The point is, you can make this event into whatever you want.  Experiment and try new things because there are people listening.  And of course, you do get a ton of summit-to-summit points.

WW7D on High Rock 2019 10-Point Madness
Josh WU7H and DJ WW7D operated from High Rock

Dave AE9Q sent an email out to the Arizona participants and inquired about the radios, antennas, and power sources used for the event and as you can probably guess, the list was very diverse.  I’m not exaggerating.  Just about every QRP HF radio, VHF/UHF handheld, Antenna, and power source you can think of was used – Log periodicals, mono-band double-bazookas, double zepps, whips, Yagi’s, end-feds, QRP and QRO HF radios of all types, HT’s with microwave capabilities, mobile vhf radios, amplifiers, lipo and lifepo batteries.  The list is long.

Sandy (W7NRS) 2023 10-Point Madness
Ray (W7USA) 2023 10-Point Madness

We recognize that other SOTA associations do similar events, like the Colorado 14er event and the Pacific Northwest Not Quite Fourteener event, to name a couple.  These are all great opportunities to get on the air and have fun with QRP radio in the field.

I’m sure you have heard about how amazing the SOTA community is.  If you get out on the summits or frequently chase, your call sign becomes familiar to others.  So much so that you feel a personal connection and sense of comradery every time you make contact with them.  During these events you see many of your good on-air radio friends.  It’s like a reunion.

The Arizona SOTA association thanks the many chasers and participants outside of Arizona who make this event more and more exciting every year.  We hope to see even more participate next year.  Just pick a summit, put your alert on the sotawatch.sota.org.uk web page, get on top of the summit and have a blast!

Readers: Do yourself a favor and subscribe to Charlie’s YouTube channel Red Summit RF. It’s chock-full of SOTA radio goodness. I’m also a fan of the All Portable Discussion Zone podcast–subscribe if you haven’t already!

Articles, Field Reports, Guest Posts, News, Portable, QRP, Travel

Guest Post: The Full Moon, Eels, and /P Operation on Mount Peyton, NL, Canada

1 Comment
VO1DR on top of Mount Peyton

Guest Post: The Full Moon, Eels, and /P Operation on Mount Peyton, NL, Canada

by Scott (VO1DR)

Introduction

I have been eyeing Mount Peyton in central Newfoundland for years as an attractive spot for /P HF operation.  Even before my radio adventure to Mount Sylvester (reported earlier in QRPer.com), I have been seeking a way to get up Mount Peyton.  Like Mount Sylvester, Mount Peyton is an inselberg of granite protruding above the glacial plain of central Newfoundland.  However, Mount Peyton is even larger and higher; an elongated ridge about 800 m long reaching up to 487 m (1,599 ft) above sea level.  For SOTA enthusiasts, it is designated VO1-CE-005, multiplier 4.

Figures 1 and 2 show the location local topography around Mount Peyton.

Figure 1 – Highway map of central Newfoundland showing Mount Peyton and landmarks
Figure 2 – 1:50,000 scale map I used during trip showing topography near Mount Peyton and our hiking route.  Each block is 1 km on a side.

Mount Peyton is a case of “so near and yet so far”.  Just west of Gander, this ridge is visible in the distance south of the Trans-Canada Highway (the main arterial highway traversing the island of Newfoundland).  However, in summer there is no trail directly to the top, and access to its base is only via rough ATV tracks and wet bogs.  One must get to the base of the mountain, then hike overland to the south side and climb a long inclined cleft in the hillside to the top.  This cleft is the surface trace of a fault in the underlying granite (see route on Figure 2).  By contrast in winter, Mount Peyton is a popular and readily accessible snowmobile destination with dozens of machines roaring up this same cleft on a thick blanket of snow.

The Full Moon and Eels

Looking at maps and Google Earth, an approach on foot would entail a three-day hiking trip.  While this sounds delightful, my current living situation would not permit this, and in addition I have no hiking buddies able and willing to make such a commitment.  So, it became clear I needed all-terrain vehicles (ATVs) to get quickly to the base, so we could do the entire trip in one long day.

I don’t own an ATV and after multiple attempts over this summer to find any ATVers interested in such an adventure, there were no takers.  Apparently ATVers like to ride, but don’t like to get off their machines ?. I finally found a local outfitter (Paul) who not only could supply ATVs, but had hiked multiple times to the top of Mount Peyton – a perfect fit.  For safety, I needed at least one extra person to go to the top.  All other potential radio or hiking companions fell by the wayside for various reasons, so it became just me and Paul.

As is common in rural Newfoundland, Paul is a Jack of all trades and is also a commercial eel fisherman.  American Eels (Anguilla rostrata) have a fascinating life history (https://en.wikipedia.org/wiki/American_eel) and inhabit freshwater rivers and streams in Newfoundland.  Paul harvests them in conical net traps anchored to the stream bottom (Figure 3).

Figure 3 – An eel trap in place in a local stream.  Eels move into the large mouth and get trapped in the bottom cage.

He told me that eels run during the new moon and stay put near the full moon.  Now doesn’t that ring deep bass notes of evolutionary biology!?  Since eel fishing is an important part of Paul’s income, we agreed to fit in my radio around his eel-catching.  He would be available around the full moon when the eels were sluggish; toward the end of September, the moon was full on the 29th.  Given the local weather, we settled on Tuesday, September 26 as our day.  Isn’t life fascinating – the moon controls eel movement, which controls human movement, which controls our /P radio expedition!

Getting There was Half the Fun

I drove from St. John’s to Paul’s cabin west of Glenwood, NL on the afternoon of Sep 25, on the beautiful shores of Indian Arm Pond (Figures 4 and 5).

Figure 4 – Paul’s cabin on Indian Arm Pond
Figure 5 – Shoreline of Indian Arm Pond

We planned an early departure on the ATVs.  Sun-up was around 7 am and sun-down was about 7 pm, so we had 12 hrs of daylight to work with.  September 26 dawned bright and clear (Figure 6) and we were soon packed and underway on two ATVs (Figure 7).  We drove for over 2 hrs on a wide range of roads, tracks, and rough trails to a point where we dropped the ATVs and started hiking (one way distance 26.7 km or 16.6 mi).

Figure 6 – Dawn over Indian Arm Pond on September 26.  Time to get moving!
Figure 7 – Scott on Polaris 450 ATV ready to go.  Black lumbar pack on right.  Blue survival bag on left.  Pole strapped on my left.  Radio and spare water in elbow compartments.
Figure 8 – Turtles are huge in Newfoundland
Figure 9 – Passing over beautiful Neyles Brook.  This is quintessential central Newfoundland scenery.
Figure 10 – Magnificent Mount Peyton looms in the distance.  This view is toward the nearly-vertical NW face.  We are about half-way there.  After dropping the ATVs, we will hike around the right end and climb up the far (SE) side.

This trip reinforced that I am not a motor sports guy.  The ATV ride was long, bone-jarring, and noisy.  Buying an ATV at great expense and doing this for “fun” is a mystery to me; and forget about seeing any wildlife.  But, hey, the ATVs got us there; we couldn’t have done this trip without them! Continue reading Guest Post: The Full Moon, Eels, and /P Operation on Mount Peyton, NL, Canada →

Field Radio Kits, Guest Posts, News, Portable, QRP

Field Radio Kit Gallery: KR8L’s KX2 POTA Field Kit

3 Comments

Many thanks to William (KR8L) who shares the following article about his portable field radio kit which will be featured on our Field Kit Gallery page.

If you would like to share your field kit with the QRPer community, read this post. Check out William’s field kit below:

KR8L POTA Field Kit Components

KX2 Bag (CS40)

Battery Bag with shoulder strap (unknown origin)

L.L.Bean ACS Day Pack with the following:

Maxpedition Beefy Pocket Organizer

  • AXE1 40 meter loading coil
  • AX1 telescoping whip
  • RG316, six feet, with BNCs
  • Manfrotto Pixi mini tripod
  • AXT1 tripod adapter
  • AXB1 bipod
  • BNC right angle adapter
  • Counterpoise, Elecraft short, for AX1, AX2 (2)
  • Counterpoise, Elecraft long, for AXE1
  • Counterpoise, homebrew with 2.5 mm banana plug, 13 feet
  • Small gear ties (2)

Maxpedition Gear Cocoon Pouch

  • AX1 loading coil
  • AX1 telescoping whip
  • AX2 loading coil
  • Counterpoise, homebrew with 2.5 mm banana plug, 13 feet

Stuff Sack #1

Stuff Sack #2

  • RG174, 25 feet, with BNCs
  • RG316, three feet, with BNCs

Stuff Sack #3

  • QRPGuys Mini 49:1 transformer
  • Tent stakes, small (3)
  • Gear Ties (2)
  • Micro paracord, 25 feet
  • Paracord, three feet (3)
  • Small bungee cords (4)
  • 40 meter EFHW wire
  • 20/10 meter EFHW wire with the following adapters:
    • 40 meter loading coil and extension (34 microhenry coil and an additional 68 inches of wire)
    • 17 meter adapter*
    • 15 meter adapter*
    • 12 meter adapter*

Loose Items in L.L.Bean pack

Note: The 20 meter EFHW wire has a connector in the middle of the length.  By unplugging this connector and removing the half of the wire at the “far” end (i.e., away from the transformer and feedpoint) and replacing it with one of these adapters, the wire is then reconfigured to be an EFHW for 17, 15, or 12 meters.

Other Items as Appropriate (most items not for hikes of any great distance)

Summary

My experience from years of traveling for both pleasure and business has shown that I always overpack and take too much “stuff”, and POTA is no exception.  However, I have made an attempt to modularize my POTA gear so that I can lighten my load depending on what type of activation I have planned and how far I will be going from my parking spot.  If you will spend some time scrolling through my blog, you’ll find examples of most of the following:

If I’m going to a location where I’m planning on operating at or not too far from my truck, I’ll take everything on this list to give me maximum flexibility as to how I set up.  Probably the most extreme setup involves erecting my 12 meter Spiderbeam mast on my heavy duty towing-style bicycle rack and deploying a wire antenna as an end-fed vertical or as a sloper.

At the opposite end of the spectrum, if I’m going to be doing a pedestrian mobile (/PM) activation then all I need is my KX2 bag, my Maxpedition Gear Cocoon Pouch, probably my Sony ICD-UX570 Digital Voice Recorder (unless I can manage to log on paper somehow), and (optional) my battery bag with shoulder strap.

If I know that I’ll be doing a wire antenna activation using a tree for support then I can wear my L.L.Bean day pack, but omit the Maxpedition Beefy Pocket Organizer and the Maxpedition Gear Cocoon Pouch.  In that case I’ll likely wear my battery bag with shoulder strap.  I may put the KX2 bag in the pack or carry it by its handle.

And, if I know that I’m going to be doing an AX1/AXE1/AX2 picnic table activation then I can omit Stuff sacks #1,# 2, and #3, but otherwise wear my day pack and battery bag as described above.

Of course, there are always variations, such as using the camera tripod, AXT1, and RG174 coax to set up at a picnic table, but allow the AX1/AXE1/AX2 antenna to be more in the clear (such as operating from a picnic shelter).

I’ve also done what you might call “pedestrian stationary”, deploying the KX2 HT-style and hand-held, but sitting in my backpacking chair.  Or deploying a wire antenna (EFHW or “random”), but sitting in the backpacking chair with the rig balanced on my leg.  By traveling with “everything” but packing in a modular fashion, there are any number of variations on how I can set up for an activation.

Field Radio Kits, Guest Posts, News, Portable, QRP

Field Radio Kit Gallery: KD7DUG’s mcHF Field Kit

Leave a comment

Many thanks to Dugbo (KD7DUG) who shares the following article about his portable field radio kit which will be featured on our Field Kit Gallery page.

If you would like to share your field kit with the QRPer community, read this post. Check out Dugbo’s field kit below:

Heli Pro Backcountry pack with portable field kit

Dugbo’s MCHF compact field kit

by Dugbo (KD7DUG)

Intro

My field radio kit is not so different or unique that it stands out from the many other experienced ham radio operators that have assembled and shared their field kits with the ham radio community. I am new in this game and by no means an expert. However, my field radio kit was designed as a fit for purpose and tailored to my CW operating needs and especially the bank account. I wanted my portable field kit to be nimble and easy to deploy at a minute’s notice. With many of the popular QRP radios backordered and even not available at this time, I chose a different route with my choice of radio.

Radio

Currently my preferred radio is the very capable SDR mcHF-QRP HF transceiver created by Chris, M0NKA. The mcHF is a smaller designed portable radio that simultaneously packs a left hook, upper hook punch, it’s a real contender. The radio is standalone, and its compact design is in comparison to other transceiver competitors with transmit and receive on 60-10 meter amateur bands with 5W output power on CW and SSB.

Currently the mcHF by M0NKA is very difficult to obtain and currently the kits are not available to purchase. However, there are multiple clones of the radio being offered by Chinese manufacturers.

Radio Equipment

Radio Equipment Kit

Priority was to protect the radio while traveling in the field. Securing the radio in a case to prevent damage from the motions of backpacking up a summit while also protecting the rig from environmental factors, dreaded dust, dirt, and water.

The Evergreen 57 waterproof dry box was a perfect match with the mcHF and additional operating equipment. The radio slides perfectly into the rubber molding of the evergreen case and prevents the radio from moving around in the case during transport.

To power the radio, I need an efficient battery for my needs. Batteries are heavy and weight was one of my concerns. Also on my mind was which battery would provide enough amp hours for an activation? To minimize the weight and provide enough power for one to two POTA|SOTA activations, I finalized my decision on a 3Ah BioEnno LIPO4 battery to supply power the mcHF. To link the battery to the radio, I am using a 5.5 x 2.1mm with an Anderson Pole connectors.

For audio I am using an Anker IPX5 speaker for GoPro sound recording along with 3.5mm Ugreen Headphone splitter for an old pair of Iphone headphones. I prefer headphones for copying incoming callsigns, RST and QTH from hunters and chasers. The headphone splitter, headphones and two additional 3.5mm connectors for speaker connection and key are packed into the rubber mesh located in the upper lid of the Evergreen case.

I am using two highly regarded and engineered portable keys. The CW morse N0SA and the BaMaKeY TP-III, are very rugged and ultra-compact twin paddle keys for CW operations.  For the BaMaKeY TP-III protection against the elements, it resides in a small waterproof case lined with foam. The N0SA paddle fits snuggly into the Evergreen case.  I use a Sea to Summit bag to carry a smaller travel case that contains the Rite in the Rain pad with pens for logging, the Anker speaker, NY4G EFHW antenna, ABR316 coaxial cable and two 10’ pieces of paracord with two tent stakes for antenna deployment.

Radio setup on Summit W6/CS-445

Once on the summit, I set up my radio equipment onto the Sea to Summit bag for additional protection from the ground. For a backup HF radio, I carry the very reliable Venus SW-3B 5W CW radio in small fly fishing Yonah Pack attached to my backpack. A perfect fit and well protected.

Antenna

I am using a NY4G 64:1 balun EFHW QRP 40,20 and 15m with additional 17 and 30m bands with a maximum of 15W on CW.

To deploy the antenna in the field in an inverted V configuration, I am using a modified 4.5m light weight expandable carbon fiber fishing pole (99g).

25-inch Valkyrie archery carbon shaft

To keep the antenna and mast vertical, I modified a 25-inch Valkyrie archery carbon shaft at one end with a 200g target tip and the other end with a center pin sleeve. No need to carry a small hammer to pound in the arrow shaft into the ground, mother nature has me covered with plenty of small size rocks in the field. I am using 15ft of ABR316 coaxial cable.

25-inch Valkyrie archery carbon shaft supporting the 4.5m expandable fishing pole

SOTA Activation W6/CS-323 EFHW antenna in an inverted V configuration
SOTA Activation W6/CS-445 EFHW antenna in an inverted V configuration

Navigation

I am using onX Off-Road GPS app on my mobile phone to download maps of selected activations. I also carry an inReach Mini Messenger satellite tracker and communicator for safe insurance. Unexpected situations can occur without warning, so I always like to be prepared than not to be.

Wrap Up

Heli Pro Backcountry pack with portable field kit

I am using a 20-year-old Dakine Heli Pro Backcountry pack to carry my compact field kit.

I used this pack for backcountry snowboarding in my early years. This pack is fantastic because of the extra compartments for carrying gear. It is also fitted with an ice axe strap that is perfect for carrying the expandable carbon fiber pole. The total weight of my portable field kit is 2.2 Kg or 4.9lbs. It might not be the lightest portable field kit setup, but it is definitely not the heaviest.

Yonahs Pack and the SW-3B

Overall, I am very satisfied with how my portable field kit came together as well as its performance in the field.

72 – DUGBO KD7DUG

Field Kit Gear

Field Radio Kits, Guest Posts, News, Portable, QRP, QRP Radios

Field Radio Kit Gallery: W2AEW’s Comprehensive Elecraft KX2 Field Kit

4 Comments

Many thanks to Alan (W2AEW) who shares the following article about his portable field radio kit which will be featured on our Field Kit Gallery page. If you would like to share your field kit with the QRPer community, read this post. Check out Alan’s field kit:

W2AEW Field Radio Kit

I’ve only been active with POTA for a little over a year, but have put together a kit that gives me lots of options for antenna deployments.

The main kit is in an old camera bag that I picked up at a hamfest for $5:

One of the outside side pockets houses a small tripod and some little ground stakes for securing support ropes, etc.

The other outside side pocket houses a small digital recorder and a cellular hot spot:

The front outside pocket houses some rubber coated twist ties that I use for securing a portable lightweight pole, as well as a few POTA brochures, QSL cards and eyeball cards:

The pouch on the inside of the lid contains a 25’ length of coax, a few extra pens and other accessories:

The main chamber houses the KX2 Shack a Box bag, a Maxpedition accessory bag, the AX1 antenna kit and my iPad:

The KX2 bag is the main bit of the kit.  Sometimes, this is the only thing I carry with me (and will often put the AX1 kit inside also):

The rightmost pouch contains the 40m EFHW antenna, which is one of my two workhorses for my activations.

The middle section holds the logging pad, writing utensils, spare wire bits for antenna and counterpoise use, lightweight clips, etc.

The main section of the bag holds the KX2 which includes the internal battery and tuner. Continue reading Field Radio Kit Gallery: W2AEW’s Comprehensive Elecraft KX2 Field Kit →

Field Reports, Guest Posts, News, Portable, POTA, QRP

Matt’s “Crackadawn POTA” Field Report

4 Comments

Many thanks to Matt (W6CSN) who shares the following post  from his blog at W6CSN.Blog:

Crackadawn POTA

by Matt (W6CSN)

This is the weekend in October that features the U.S. Navy’s Blue Angels taking to the skies over the Bay Area. The air show takes place over the Bay waters, which means the beaches and shorelines around San Francisco will be packed with people and traffic. Since my usual POTA operating location is right by East Beach, I had pretty much given up on the idea of activating K-7889 this weekend.

Lights of the Golden Gate Bridge reflecting off the still Bay waters.

The airshow is on Saturday and Sunday, but the Blue Angles practice on Thursday and Friday, weather permitting. So here I was on Friday morning, awake at 5AM watching K4SWL on YouTube doing POTA when the idea of getting out for an early activation got into my head.

It was still dark when I tossed my backpack, which was already loaded for POTA from the previous activation, into the car and headed down to the East Beach in the Presidio of San Francisco National Historic Site (K-7889).

The sky getting lighter in the East before sunrise.

Given the early hour and low light conditions I didn’t relish the idea of doing my usual picnic table and tripod antenna setup. Not long ago I had acquired one of those “mirror” antenna mounts with the jaw clamp arrangement, and this was a great opportunity to try it out. Between the parking lot and the beachfront promenade there is low fence constructed of short steel posts and strands of stainless cable. The fence post was a perfect place to attach the clamp and the MFJ-1979 17 foot telescopic whip, which is a quarter wave on 14 MHz.

Close up of the MFJ-1979 whip antenna clamped to steel fencing.

I was ready to string some radials out to give the antenna a ground plane to work against, but wondered if the post, being sunk into the ground by the Bay and the steel fencing cables might provide enough of a counterpoise. A quick check of the SWR on the meter built into the MTR-4B showed a 1.2 to 1 – no need to even bother with radials with an SWR like that right out of the box.

Low SWR on the quarter wave vertical as the Bay wakes up.

The other advantage of this antenna setup was that it is right next to the car. However, I don’t really like operating from my vehicle as it’s not very sporting nor is it comfortable. Instead, I simply set the station on the trunk lid and completed the activation from a standing position. The other advantage of this arrangement was that I could closely guard the RG-316 coax going from the radio to the antenna to keep any humans or canines from getting entangled. Continue reading Matt’s “Crackadawn POTA” Field Report →

Field Radio Kits, Guest Posts, News, Portable, QRP, QRP Radios

Field Kit Gallery: K2EJT’s Self-Sufficient Elecraft KX1 Field kit

16 Comments

Many thanks to Evan (K2EJT) who shares the following article about his portable field radio kit which will be featured on our Field Kit Gallery page. If you would like to share your field kit with the QRPer community, read this post. Check out Evan’s field kit:

KX1 Field Activation Kit

by Evan (K2EJT)

I take a minimalist approach to most of my gear.  I don’t like to carry anything I don’t need.  Whether it’s what I pack in my daypack, an overnight pack, or my radio kit…..If I don’t need it, it’s probably not coming along.

That’s where this kit comes in.

This is the absolute minimum radio kit to do a field activation.  While it’s not the lightest kit I have, it still comes in at only 1008 grams (2.25lbs), and that’s including the Pelican case which makes this kit rugged and waterproof (I have an SW-3B kit that weighs 700g, but it’s in an ultralight stuff sack).

This kit contains EVERYTHING (and I mean everything) to do an activation.  The radio is an Elecraft KX1.  It’s a four band radio with the internal ATU.  Powering it are six AA Lithium Ion batteries.  I love this radio, and I wish it was still in production, but these days they’re unobtanium unless you’re willing to spend a ton of money and get lucky and find one for sale.

The CW key is a cwmorse.us N0SA paddle.  The headphones are a pair of old SkullCandy earbuds I’ve had forever, but sound great.

For an antenna I’m running a 41’ random wire antenna, with a 17’ counterpoise, constructed of 24ga silicone jacketed wire.  That’s attached to the radio via a BNC binding post.  While this setup isn’t the most efficient, it’s definitely the most compact and agile.  Normally I run resonant antennas, but having the tuner allows me to run the absolute minimum antenna, and swap bands quickly, and that was the idea behind this kit.

The throw bag is rip-stop nylon with a paracord loop sewn in the top and a velcro closure across the opening.  I fill that bag with rocks, seal it shut with the velcro, and it’s ready to go. The throw line is 65’ of 1.8mm high vis reflective cord.  The throw bag doubles as a stuff sack for the cordage, so it’s all contained in one neat little unit that rolls up tiny.

Also included in the kit are a pencil and a logging sheet, as well as the KX1 cheat sheet.

I have lots of other field kits, but I wanted to showcase just how little you can actually get away with and still get the job done. Yes, I know you could build a Pixie kit and a tiny home made key and stuff and make the kit smaller and lighter, but I wanted a kit with no major compromises or downsides.  This fits the bill.   There’s nothing like a 100% complete kit that contains literally everything you need to do an activation that fits in the palm of your hand!  Thanks for reading and 73!

Evan

K2EJT

Equipment:

Everything else is either generic, home made, or ancient.

Readers: Check out Evan’s YouTube channel for more field radio goodness.

Field Radio Kits, Guest Posts, News, Portable, POTA, QRP, SOTA

Field Kit Gallery: NL5E’s Lightweight KX2 SOTA/POTA Alaska Backpacking Radio Kit

9 Comments

Many thanks to Eric (NL5E) who shares the following article about his portable field radio kit which will be featured on our Field Kit Gallery page. If you would like to share your field kit with the QRPer community, read this post. Check out Eric’s field kit:

NL5E SOTA/POTA Backpacking Kit

Description

Hello! NL5E here.

I’m one of the rare SOTA activators in Alaska (I also use this same kit for POTA). Anyone that has looked at a map of this state will know that we have some interesting difficult topography. Many of our summit hikes start out near sea level, but are 3000-6000 vertical feet of climbing to get to the summit. So I built my kit with compactness, versatility, and weight in mind. Everything weighs approximately 2lbs (not including the battery, I don’t always take it).

My primary operating modes are CW, FT8, and SSB.

To facilitate those modes I tried to keep everything as small as possible while still being usable. For example, I debated using N6ARA’s tiny paddle, but I found I made too many sending errors. The N0SA paddle is a perfect medium between portability and sending ability. For FT8 the FT8CN app has been a good alternative to carrying a Raspberry Pi or small laptop and the well loved Digirig is probably the best audio/cat interface on the market today. I don’t do a lot of SSB (especially at QRP levels), but the K6ARK mini microphone is a wonderful improvement over Elecraft’s comically massive microphone for the KX2. I added headphones so I don’t disturb anyone on popular summits and so I can hear CW a bit better.

My antennas of choice tend to be random wires and End Fed Halfwaves.

With the KX2 I chose to use K6ARK’s 20w antenna kits and built both a 9:1 and 49:1 version. I usually carry the 9:1 just to have the band flexibility as it will work from 40m-10m. If the ground is wet enough I’ve had it tune up to 80m.

For the 49:1 I chose 20m because bands lower than that have mediocre performance from the latitude. Because of how short both these antennas are, they pair very well with the SOTAbeams Carbon 6 mast. From a summit a 19’ mast is usually tall enough to work most of the US and lots of Asia from here. The only modification I made is gluing the top 2 sections together for durability. To attach the antenna wire I use a small Niteize carabiner and a prussik loop.

I also wanted to ensure that I could power many different devices while out hiking. I settled on an Anker battery because it is easy to power phones and the radio without having to bring a bunch of different adapters like I would with a dedicated 12V battery.

I know someone will mention protection and the bag I chose. Yep, a silnylon stuff sack offers zero protection from bumps and impacts. I firmly believe that hams “over baby” their equipment and think that their radios will hilariously explode if sneezed on wrong. I settled on the Gems Products cover and rails as a good solution to keep the radio from getting destroyed in a backpack. So far so good. I added the dry bag to my list for rainy days.

I didn’t include one in the images, but I also usually have an HT with me, but most summits don’t have good line of sight to our population centers. I usually run a Yaesu VX-6R with Diamond RH77CA or MFJ Longranger. I will usually run 2m FM when I am close to Anchorage or Palmer. I also didn’t include my logging solution, but that is usually HAMRS on my iPhone or a Rite in the Rain book and pencil. I find CW is easier to log on paper for some reason.

Thanks for looking and perhaps I’ll hear some of you on the air.

Component List

Radio: Elecraft KX2 with Side KX Heatsink and Cover

Antenna: K6ARK Random Wire with 29’ of polystealth wire and antenna winder

Note: I also run a 49:1 EFHW cut for 20m (not pictured, looks the same).

Dog: Luna. Standard issue Alaska Husky. Smol in size. Adds 5 dB gain to all antennas. Adds 45 lbs, but is self transporting.

Support: SOTAbeams Carbon 6

CW Paddles: CW Morse N0SA SP4 Paddle

Microphone: K6ARK mini microphone with printed case. Built from Digikey Parts.

Headphones: Sony Earbuds – could be any old ear buds. These work fine.

Digirig Mobile with Cables: Lets face it. Sometimes FT8 is all that works. I’m in Alaska.

Android Phone: Galaxy S10. Dealers choice for a phone. It exists only to run FT8CN instead of carrying a laptop for FT8.

Power: 

–JacobsParts 15V 5A USB C PD cable 5.5×2.5mm DC (Ferrite Added)

Note: Outputs approx. 14.5V when measured using my multimeter. Radio shows the same/

–Anker 747 25600mAh battery

Miscellaneous Items:

–5.5×2.5mm to 4.0×1.7mm DC Adapter: Allows charging of various HT radios using the Anker battery with JacobsParts USB C cable

-Shower Cap: The all important rain cover for the KX2. Just in case. Just make sure it is transparent.

Storage: Sea to Summit 3L UltraSil Stuff Sack or Sea to Summit 3L Dry Bag

Articles, Field Radio Kits, Guest Posts, News, Portable, POTA, QRP, QRP Radios

Field Kit Gallery: W4EMB’s Penntek TR-45L Portable Kit

14 Comments

Many thanks to Ed (W4EMB) who shares the following article about his portable field radio kit which will be featured on our Field Kit Gallery page. If you would like to share your field kit with the QRPer community, check out this post. Ed writes:

My QRP Portable Set up

by Ed (W4EMB)

Radio: I have one priority rig I use 99% of my time. It is the TR45L Penntek. I have both versions. The fullsize one with built-in tuner and battery, I also have the “Skinny” version. The skinny does not have the tuner nor battery. My second Rig is the Yaesu 817 with the Windcamp Battery upgrade. I also have a 40m only QSX and the 5 band TruSdx.

Penntek TR45L Skinny with external batter and external tuner.

Antenna:  I use the Chelegance MC-750 most of the time, but also use a Homebrew EFHW with 49:1 balun and 67’ of wire.

I have the QRP guys Tri-Band vertical kit, and two pieces of 16ga Speaker wire cut to 33’ that I carry as well. To support the EFHW and Speaker wire antenna, I use the SOTABEAMS 10m (32 ft) “Travel Mast”.

For the QRP Guys Tri-band vertical, I use the SOTABEAMS Carbon-6 ultra light 6m (19.6 ft) mast. To support the 32’ mast I usually just lean it into the trees and slope my EFHW up from the feed point.

For the speaker wire antenna, I run the “red wire” straight up the mast while it is strapped to the picnic table. The “black wire” is simply thrown out across the ground. I might even elevate the black wire with sticks.

My carbon-6 fits right into a piece of 1 ¼ inch PVC pipe I have clamped to my brush guard on my van. Or, I use a Tiki-Torch stake to hold my carbon-6 in open ground.

carbon-6 with Tiki-Torch stake supporting and using the Tri-band Vertical.
carbon-6 inside of PVC pipe with the QRP Guys Tri-band vertical.

I find for me, that my QRP Guys antenna works great on 20m without a tuner. But when I try to use it on 30m or 40m, I require a tuner. For this reason, I lean on my MC-750 to be the main antenna.

I have modified my MC-750 slightly. I made my own set of radials to match the factory ones. I chose to make them out of silicone wire. I find it to be more flexible and does not kink or tangle as easy as the standard factory radials. I used 3mm banana plugs and 24ga yellow wire. I also crimped small ring connectors onto the ends of the radials. I did NOT strip the insulation and place them on the wire. I simply crimped them on the silicone. I use them to stake down the wire. I use four nails as “stakes” to pin the wire down. I find I only stake the radials out when I am on un-even ground.

The second modification, I made a set of “double” radials out of 26ga green silicone wire. Colors do not matter. It is what I had. I spread them evenly around the base of the MC-750.

MC-750 with “double radials” and RG316 for coax.

My key is a Czech military straight key from the 1950s. It was new old stock when I bought it. I also carry a small mini set of paddles. For the TR45L radio, I can not play my recoded CQ or 73 with out a paddle. The “play” button is dit or dah trough the paddle jack.

For coax, I use RG316 and the appropriate adapter for the MC-750.

I have two pencils from Kuru Toga. One pencil is .5mm the other is .7mm. I make my own POTA log sheets and I paper log, and then type them later. I am a not talented enough yet to play with a tablet or PC while operating. I have only done CW for the last 12 months.

On my table: I have a really thin yoga mat. I find the concrete picnic tables a bit rough on my equipment. The yoga mat can get a bit sticky when it is warm, so I drape a small hand towel over the edge where my arms lay. I also have a Write in the Rain tablet in full size paper. I have been out early in the mornings in this summer and humidity and steamy fog makes normal paper hard to write on. The .7mm pencil matches up well with the Write in the Rain paper.

Chelegance antenna pictured in the background. K-2965 Paris Landing State Park

I have found CW and POTA have re-energized my ham radio hobby and resurrected it from a dusty shack, to a fun out door activity.

My first challenge was how to get from the car to the table in one trip. Downsize to the necessities. Next was figuring out the antenna and radio combo that could work in different conditions. By conditions I mean space.

Location, location….. I had a dog run between me and my antenna. It pulled my radio right off the table and tumble behind the dog. So now I choose my locations like Bill Hickock… always face the door. Hihi. Food for thought.

Thank you to Thomas for inspiring me to get out there and do it. His you tube videos were great copy practice to give me the confidence to get out there. Finally, my Elmer. John, KM6NN. Without him I would have never started my CW journey. He is a true Elmer in every definition of the word. I am proud to know him and lucky he is in my life. Thank you John.

Gear:

Note: Check out W4EMB on YouTube as he makes his 1st POTA “Kilo”