All posts by Vince VE6LK

Big ships and 78GHz by chance!

As always there are lots of links within the article. Click one! Click them all! Learn all the things!

by Vince (VE6LK)

In August and September 2024, I was travelling around Southern Ontario for some family matters and naturally I brought my radio kit with me to squeeze in some radio therapy stops along the way. This is the report of my stop at CA-6341 Welland Canal System National Historic Site along with CA-6096 Battle of Beaverdams National Historic Site.

This activation took a bit of research to figure out the intersection of the two given that the landscape had been dramatically altered from the time of the Battle of Beaver Dams in 1813. For example, at that time, the Welland Canal did not exist! So the town of Thorold has a park located at the west end of the battle site, and I was able to locate a monument at the east end, thus I was able to extrapolate and see that Lock 7 was in a direct path between the two. Thus I settled at Lock 7 for the activation.

A borrowed grocery cart serves as a mast support given the hard soil. Antenna runs off to the vehicle on the right.

This activation was done later in the day after my “Cross-Border Activation between Friends” and I was pleased to note the conditions had improved a fair bit.

I started off on CW, hunting other friends that were activating (shout-out to Ed W4EMB!) and then switched to SSB QRP where Steve KO4AFL found me and we had a brief chat before we both moved on. I stayed on 20m for this activation.

A quick drive-up activation means operating from the trunk

The Welland Canal is an engineering marvel that allows lake freighters to traverse the 100m/326′ height difference between Lake Erie and Lake Ontario.

Opened in 1833, it sees an average of 3,275 freighters during the shipping season which runs about 9 months of the year. With that sort of traffic, you can be reasonably assured that you’ll see one of these huge freighters on the day and time that you visit the area.

List of gear used for these activations:

Note: All Amazon links are affiliate links that support QRPer.com at no cost to you.

Summary

After my earlier activation with N2MAK, we drove down the Niagara Parkway past Niagara Falls and Niagara-on-the-Lake before arriving at the Welland Canal. It was a pleasant day and not terribly humid.

VA3ELE, Peter, with an attempt to set a new distance record on 78GHz

One last ham radio related story to the day was running into Peter (VA3ELE) about 1km from our home-away-from-home as he was attempting to set a new distance record with a friend who was well over 100km away.

Peter explained to me that his radio was 3W and the dish yielded 47dB of gain thus his ERP was around 14,000W see below. Needless to say that I did not stand in front of the dish.

[EDIT Sept 26] with gracious thanks to the math wizardry of David VE7EZM, the result of 47dB of gain with 3W of input is approximately 150,356W ERP.

All in all, labour day 2024 was full of beautiful scenery and lots of Ham Radio – exactly how a vacation day should be in my books.

72 and dit dit,
…Vince

First introduced to the magic of radio by a family member in 1969, Vince has been active in the hobby since 2002. He is an Accredited examiner in Canada and the USA, operates on almost all of the modes, and is continually working on making his CW proficiency suck less. He participates in public service events around Western Canada and is active on the air while glamping, mobile, at home or doing a POTA activation. You can hear him on the Ham Radio Workbench podcast, follow him on Twitter @VE6LK, check out his YouTube channel, and view the projects and articles on his website.

When three contacts equals a successful activation

As always there are lots of links within the article. Click one! Click them all! Learn all the things! ?

by Vince (VE6LK)

In August and September 2024 I was travelling around Southern Ontario for some family matters and naturally I brought my radio kit with me to squeeze in some radio therapy stops along the way. This is the report of my stop at CA-5367, McQuesten House / Whitehern National Historic Site.

View from the rear of Whitehern showing nearby office tower

This site is located in downtown Hamilton and among the tall building and features a walled rear garden. It is open to all visitors and there is no fee to visit the facility. This two-storey neoclassical house was the home of a prominent family, the McQuestens, and retains many of its original Victorian and Edwardian fittings and furnishings. It is now a museum open to the public.

This activation was strictly by chance and I had less than an hour before I was due to be someplace else. I did not check the solar conditions in advance nor anything about the site. Sometimes just showing up is fun in and of itself, am I right? So I found my way around to the rear garden and found a bench in an out-of-the-way corner and set up for a low impact activation.

I deployed my AX1 on it’s small tripod and placed it on the ground and ran out a 20m counterpoise wire beside the walking path. I set myself and the radio gear on a park bench along the path. It truly felt like a small enclave!

After calling for 10 minutes with zero replies I checked the solar conditions and see that a small flare had just hit. That might explain the soft conditions, and combined with the compromised antenna and its close proximity to me. I moved the antenna away from me as far as the feedline would allow. Only then was I able to log just a few contacts and those were hard-fought. Then I ran out of time.

The author in his temporary enclave
A partial log. Contacts were not obtained by calling out, but by hunting others.

List of gear used for these activations:

Note: All Amazon links are affiliate links that support QRPer.com at no cost to you.

Summary

I’ve spoken before about “getting to 10” with a POTA activation. For me, that’s always one of my goals. But it isn’t the only goal. I also enjoy the new scenery, the journey, the research and the challenge. This visit was high on the scenery and the challenge end of the scale for sure.

72 and dit dit,
…Vince

First introduced to the magic of radio by a family member in 1969, Vince has been active in the hobby since 2002. He is an Accredited examiner in Canada and the USA, operates on almost all of the modes, and is continually working on making his CW proficiency suck less. He participates in public service events around Western Canada and is active on the air while glamping, mobile, at home or doing a POTA activation. You can hear him on the Ham Radio Workbench podcast, follow him on Twitter @VE6LK, check out his YouTube channel, and view the projects and articles on his website.

Castles and Trains at Dundurn Castle NHS

As always there are lots of links within the article. Click one! Click them all! Learn all the things!

by Vince (VE6LK)

In August and September 2024 I was travelling around Southern Ontario for some family matters and, naturally, I brought my radio kit with me to squeeze in some radio therapy stops along the way. This is the report of my stop at Dundurn Castle National Historic Site, CA-5360.

Located in the city where I was born, Hamilton, Dundurn Castle has been a landmark since 1834, when the land was sold to Sir Allan MacNab. The castle is located on Burlington Heights, the site of a fortified military encampment established by the British during the War of 1812.

MacNab was a railway magnate, lawyer and Premier of the United Canadas (1854-1856). Today Dundurn Castle tells the story of the family who lived above stairs and the servants who lived and worked below stairs. He was a defining figure in so many ways in the local history, and performed the original survey of home lots and land in the Hamilton area. Indeed, the home I was born in (on MacNab Street no less) was on land once deeded to its owner from MacNab.

And Dundurn Castle has a personal tie in for me as my father, a finishing carpenter, worked tirelessly on it’s restoration in the mid 1960’s leading up to Canada’s Confederation Centennial in 1967. As kids we spent a lot of time on the grounds.

Continue reading Castles and Trains at Dundurn Castle NHS

CW Three Band Activation Among the Giant Timbers

As always there are lots of links within the article. Click one! Click them all! Learn all the things! ?

by Vince (VE6LK)

In August and September 2024 I was travelling around Southern Ontario for some family matters and naturally I brought my radio kit with me to squeeze in some radio therapy stops along the way. This is the report of my stop at Hamilton Waterworks National Historic Site (CA-5365).

It was a rainy Friday morning as I departed at 0730h to get in some radio therapy before getting to the fishing store and getting some more of the Fishing Butler bungee straps I’d picked up a week prior. And, as it happens, Fishing World in Hamilton was pretty much around the corner from CA-5365. I’d chosen this site as it had never been activated in CW.

The Hamilton Waterworks National Historic Site is “…a gracious complex of mid 19th-century brick industrial buildings…” located in the North-East end of Hamilton near Lake Ontario. It is part of Hamilton’s original water works complex which sprawls along Woodward Avenue.

And it is delightfully radio quiet, however the noise from the local street was the real challenge for me. Next time I’ll use earbuds.

The original wood shed serves as a covered picnic and teaching area for students that visit the Hamilton Museum of Steam and Technology, part of this NHS.

This is one site I drove to without much research and I was prepared with a backup site were I not able to activate it for whatever reason. Thus I was pleasantly surprised when I saw a large covered area with picnic tables and a small grass area outside to stake down my Carbon Fibre mast. Hoisting/throwing the wire turned out to be a challenge given the shape of the giant support timbers (rounded) as the wire would fall into the narrow end of the crevice, so with some creative use of the CF mast, I was able to essentially fish it into place. Later removal was the reverse process for the same reason.

All set up and ready to go with my 20-30-40m EFHW trapped antenna

I checked the solar conditions and it showed low K and moderate A indicies, and then I verified with a spin of the VFO to see what I could hear. I set my power at 5W and began the activation on 20m. Being located in Ontario, I hear a different set of regular callers than I may otherwise when at home in Alberta. Still a fair number of callsigns are immediately recognizable and they put a smile on my face.

I had planned this to be a CW only activation to exercise my brain. I worked my way from 20m to 40m then to 30m. I was surprised with the short distances on 30m working a couple of stations in Ontario that were less than 75 miles away.

After catching 30 in the log my time was up and the rain had started -along with nearby thunder- so I hastily disconnected the coax and took down my antenna and got on with my day.

List of gear used for these activations:

Note: All Amazon links are affiliate links that support QRPer.com at no cost to you.

Summary

It was wonderful to spend time among such elegant buildings that have stood there for 167 years. The park is a peaceful place in an otherwise industrial end of an industrial city and is a delight to visit. I hope to do so again soon.

72 and dit dit,
…Vince

First introduced to the magic of radio by a family member in 1969, Vince has been active in the hobby since 2002. He is an Accredited examiner in Canada and the USA, operates on almost all of the modes, and is continually working on making his CW proficiency suck less. He participates in public service events around Western Canada and is active on the air while glamping, mobile, at home or doing a POTA activation. You can hear him on the Ham Radio Workbench podcast, follow him on Twitter @VE6LK, check out his YouTube channel, and view the projects and articles on his website.

Summer evening activation with a buddy

As always there are lots of links within the article. Click one! Click them all! Learn all the things!

by Vince (VE6LK)

In August and September 2024, I was travelling around Southern Ontario for some family matters and naturally I brought my radio kit with me to squeeze in some radio therapy stops along the way. This is the report of my stop at Canal Park Conservation Area CA-5567 in Dundas.

The chimney from the former greenhouse remains standing today

Canal Park is located at a former greenhouse site that is growing back to a natural state, and is long the bank of the former Desjardins Canal that was built in the early 1800s.

The story of the Desjardins Canal

Many of the timbers that were needed for the canal can still be seen standing today despite being immersed in water for nearly 200 years.

The canal’s historic timbers as seen inside the park

It is a popular spot for birdwatching; some of the visitors told me that they routinely see Herons gracing the area. It is also only a few minutes from downtown Dundas and nearby McMaster University. I arrived at 1700h local time and so I had about 3 hours of sunlight to work with which would be plenty of time for a chat and activation.

The site has a large deck and pergola overlooking the canal along with a few park benches, so I got to work setting up my 20-30-40m trapped EFHW that I built a few months ago. It’s short at only 35′, small and works very well. Look on Alan W2AEW’s YouTube channel for build videos.

I used the toroid on the end of my RG-174 feedline as a crude throwing weight and chucked it up and over the steel structure and it dangled down low enough to grab it. I then attached it to my Spark Plug Gear transformer and antenna and used the feedline to raise it back in place. Yes, I leave the wire winder in place for convenience.

Feedpoint of antenna about 15′ above the ground

At the far end, I set up my Goture CF mast and ground stake. The antenna landed up being about 15′ in the air. I wasn’t expecting stellar performance on 20m with it but was hopeful. I was very wrong to think that, with the first station I heard from Macedonia.

CF mast staked into the ground for end support

But not only was I here to POTA, I was here to meet, in person, Wayde Nie VA3NCA/AD2GX. He and I have been delivering remote examinations on the Ham Radio Crash Course team for some time now. Our paths have crossed many times in the virtual world, and finally now would cross in the real world. Needless to say I was looking quite forward to this activation and the location and beauty in this small park were only part of the whole story.

VE6LK and VA3NCA enjoying some late-day sun and QRP SSB

After Wayde showed me his wonderful portable kit, and with mine already deployed, we got to work at 10W on SSB. It wasn’t a fast and furious pace but it was steady enough as a 2 operator activation that we were kept busy. The real surprise were the stations that called us back from Spain!

10W on SSB carries pretty far some days. One contact to Spain was 5W CW.

I rounded off the activation with a quick CW contact to Spain. Wayde is early in his CW journey and would depart for home to his LICW class later that evening but followed the contact along pretty well!

List of gear used for these activations:

Note: All Amazon links are affiliate links that support QRPer.com at no cost to you.

Summary

I grew up in Hamilton and Dundas was one of my favourite place to visit. I did this activation in early September on a wonderful late summer day and the evening was warm and calm. While I live in Western Canada where there isn’t much in the way of humidity, I found the weather to be quite pleasant (until the mosquitoes dropped by) and the company was excellent too!

72 and dit dit,
…Vince

First introduced to the magic of radio by a family member in 1969, Vince has been active in the hobby since 2002. He is an Accredited examiner in Canada and the USA, operates on almost all of the modes, and is continually working on making his CW proficiency suck less. He participates in public service events around Western Canada and is active on the air while glamping, mobile, at home or doing a POTA activation. You can hear him on the Ham Radio Workbench podcast, follow him on Twitter @VE6LK, check out his YouTube channel, and view the projects and articles on his website.

Cross-border activation between friends

As always there are lots of links within the article. Click one! Click them all! Learn all the things!

by Vince (VE6LK)

In August and September 2024 I was travelling around Southern Ontario for some family matters and naturally I brought my radio kit with me to squeeze in some radio therapy stops along the way. This is the report of my stop at the Battle of Lundy’s Lane National Historic Site CA-6216.

As like many sites around the Niagara Peninsula, it is rich in history from the war of 1812 between Canada and the United States of America. It would therefore be only fitting that I would meet up with my friend Mike Kennerknecht N2MAK for a joint activation. The plans were made, and at the last minute he surprised me with a request.. but I’ll tell you about it later on.

This site is at the top of a hill in Niagara Falls along Lundy’s Lane, one of the main roads in the city. It’s easy to see why it was strategically important for both sides to capture the hill, and indeed both sides claimed success in the battle depending on where you read up about it.

The words on this monument summarize the relationship between our two countries perfectly.

It was great to meet Mike in person as we’d only worked together virtually on teleconferencing platforms. The park was about halfway between us, not counting the stops he’d make at the border each way. It was 5 years since he’d last been in Canada and he was excited for the Duty Free stop he’d make on the way home. And he travels prepared for sites and brought along a couple of chairs and a small side table for our use, which beats a park bench any day of the week.

I was able to get my Goture carbon fibre mast up with my 20-30-40m trapped EFHW (see links below) just before he arrived along with my KX3,. He deployed his Gigaparts POTA Explorer 20 CF mast with a 20m EFHW to his IC-705; later he switched to 17m.

We both started off on SSB with me on 40m. Despite the very close proximity of our antennas, interference between us was very minimal.

Goture (left) and POTA Explorer 20 on the right. A similar amount of flex is seen despite the big differences in their construction.

At around 1100h local time we began calling at 10W on SSB. Mike was able to get to his 10 fairly easily but on 40m I was limited by the NVIS configuration with my average height at 3m for the 40m band, so once he was done on 20m, he switched to 17m and I moved to 20 to complete my activation.

And then he said the words that were magic to my ears: “Let’s do CW”. To be fair he gave me some heads-up that he wanted to do this when he asked if I had 2 CW keys with me. And he wanted his first CW contact to be made in Canada. Thus with a bit of pre-planning, and a pair of dummy loads, we set out to make the contact, Park-to-Park no less.

What I hadn’t realized is that he had never done CW before today, but with bravado and a Quirky QRP Reference Mat at his disposal, we got into it. I explained what each side of the paddle key does (dit vs. dah), however we both didn’t know how to adjust the speed on his IC-705 from it’s default of, I think, 15WPM. No matter, after a few minutes of rehearsing his callsign along with a handwritten chart I’d built him, he was ready.

With our respective radios in close physical proximity, signals were quite strong. I showed him the typical exchange for a POTA and then it was showtime. We did the exchange, and for good measure we did it on the 6m band. That CW contact was the first one done at the park as well.

Mike’s the tall guy on the left

We retired to a well-deserved lunch and went about our respective ways after the required team photo and a bear hug. I’m so delighted I got to connect with him on this trip, and especially for a cross-border activation.

Mike’s Video

List of gear used for these activations:

Note: All Amazon links are affiliate links that support QRPer.com at no cost to you.

Postscript

This was the first activation with my new Bass Pro Shops Extreme tackle bag and I am very impressed. It is the correct size for me and everything works as it should. As a matter of fact, It inspired me to create a new channel on the Ham Radio Workbench’s Discord called #bag-talk if only to prove that bags need not be expensive in order to be functional.

72 and dit dit,
…Vince

First introduced to the magic of radio by a family member in 1969, Vince has been active in the hobby since 2002. He is an Accredited examiner in Canada and the USA, operates on almost all of the modes, and is continually working on making his CW proficiency suck less. He participates in public service events around Western Canada and is active on the air while glamping, mobile, at home or doing a POTA activation. You can hear him on the Ham Radio Workbench podcast, follow him on Twitter @VE6LK, check out his YouTube channel, and view the projects and articles on his website.

Fish Creek Provincial Park: My most frustrating activation to date

by Vince (VE6LK)

All I wanna know is howcome our local star decides to throw in a monkey wrench when I go to activate? Huh? Huh?

Monday August 5 was a statutory holiday for me and I decided to get out early at a popular picnic area in south Calgary and get some radio therapy. I listened to the IARU beacons while driving and even 15m sounded promising.

I’m not nearly as adept as Thomas at using an arborist throw line as I famously exclaimed once and had to be beeped out, so it took me close to a half hour to get my VE6VID OCF antenna how I wanted it with one end supported by the tree and the opposite my carbon-fibre mast. Given I was also setting up video equipment, It was an hour before I made my first contact from when I had arrived.

I started off very optimistic that I’d be able to get 10 contacts as I was hearing all kinds of DX on 20m FT8. I connected my iPad with iFTx software along with some cables I heard about via KD7DTS and I started working it off at 1 watt (just to be cocky) and it took me a while to get 2 contacts. This simply won’t do as I don’t have all day!

So I switched to CW. 10 minutes of calling and only one spot on RBN at 5 watts. So I did what any reasonable person would do and I moved to 10 watts because more is better, right?

Two entries in RBN, one for 5W and the other for 10W.

I then had a couple of contacts. At one point I did a visual check to ensure my antenna wasn’t on the ground (it wasn’t). So I proceeded with my logical thinking and moved to SSB at 10 watts, because after all, I was there to experiment! Clearly I was delirious to think that SSB would be better than CW – that’s my story and I’m sticking to it!

This got me nowhere, slowly. Me, I prefer nowhere fast, but beggars should not be choosers. After 20 minutes of calling on SSB I decided it was time for more powah! and thus I took down my gear and moved into my truck with the trusty FT-857D and the ATAS-120A antenna with the lengthened whip. By this point I had zero hesitation to run 100 watts as I’d been at the park for close to two hours.

I posted a spot and began calling. I even turned my spotting into something humourous in an attempt to woo callers:

I got creative when posting spots 🙂

Along the way I attracted at least one bystander and spoke with them about the hobby for a bit, and I worked 4 contacts between being hunted and being the hunter. At least those 4 “only” took 15 minutes. But they were getting progressively harder. Can you spot why in the image below?

A=46

I’ll give you a clue: it starts with the letter A. I had noticed some small M-class flares over the past couple of hours and they were adding up fast. Conditions were deteriorating for me. I must have been damn near a direct hit to those flares, as others in the southern USA were making 50 contacts an hour at the same time as I wasn’t. So I finally did the right thing and moved to CW at 100 watts. I felt like Scotty “I’m givin’ ‘er all I can Cap’n!” …

…and I was met with mediocre results. Nobody answered my calls so the remaining contacts I obtained were found by hunting. Some that were calling were super loud to me and giving out 72s -indicating they were QRP- but could not hear me after my callsign was given 4 times. My final contact was with my friend VE3JO who has just returned to CW and was at a slower pace which helped to bring my blood pressure down a notch 🙂

Summary

Yes, there is a video with plenty of wise-cracking with myself to reduce tension, one of my coping mechanisms.

It’s not a race, sometimes it is a marathon that you didn’t plan on and only takes patience to have whatever you define as success finally fulfilled.

Still, how bad is it to be out in a park for a bunch of hours? It’s not too bad at all if you ask me!

72, 73 and dit dit,
…Vince

First introduced to the magic of radio by a family member in 1969, Vince has been active in the hobby since 2002. He is an Accredited examiner in Canada and the USA, operates on almost all of the modes, and is continually working on making his CW proficiency suck less. He participates in public service events around Western Canada and is active on the air while glamping, mobile, at home or doing a POTA activation. You can hear him on the Ham Radio Workbench podcast, follow him on Twitter @VE6LK, check out his YouTube channel, and view the projects and articles on his website.

A tale of two back to back activations

by Vince (VE6LK)

On Sunday July 28 I needed some shortwave therapy. I headed west from Longview Alberta to find a location on Highway 541 where I could have the perfect convergence of having cell service and be within a POTA entity and near to the mountains. This would allow me to receive any updates about a family member (none happened) while getting a break from home and to play radio.

Along the drive I took time to listen to the IARU beacons and was pleased to hear bits of VK and ZL on 15m so I was hopeful that my plan for two QRP activations -one CW and one SSB- would be successful.

I would discover just how difficult it was at the second activation … but I’m getting ahead of myself.

Activation One: Sentinel PRA

After some driving around and testing cell service at a few roadside points, I landed up at the Sentinel Provincial Recreation Area which is just inside the boundary of Kananaskis Country. This would offer me the luxuries of a bench or table along with a stunning view. While it’s not a unique entity itself in the POTA system, it is part of the larger CA-6112 that is K-Country.

Sentinel PRA is at the confluence of the Highwood River and Cataract Creek and is, like many in this area, an equestrian-focused facility. Unlike many, it’s mixed-use so day-users like me are also welcome here. Upon my arrival I was fortunate to see a few equestrian users heading out of the backcountry. What was unusual to this city-raised kid was the covered wagon a small team was pulling. Perhaps the team was training for a future cattle drive?

I set up my cameras and my radio gear and got to work at a park bench overlooking the river. I released a video of the river suitable for background white noise and to practise your Zen and/or Yoga.

I secured my carbon-fibre mast to the bench, used a small weight to hold down the 17′ counterpoise, and deployed the 41′ main segment out to a 10′ fishing pole lashed to a sign nearby. I used my carrying totes (sometimes used for groceries) as a makeshift desk. It all worked out well enough. I began my CW activation at 5 watts.

The author logging a contact

I did a basic video of the activation which you can see here:

Thirteen contacts and about 20 minutes later at 1930UTC, I called it a wrap and packed everything down to head to my next site. I wouldn’t say that conditions were stunningly good or anything, and some were downright hard to copy while others were incredibly loud. Given what I heard of the IARU Beacons on 20, 17 and 15m I wasn’t too surprised. I would later on learn that meant some solar action had happened as you’ll see in this chart.

Activation Two: Bar-U Ranch NHS

About an hour’s drive from my last stop and just south of Longview is the Bar-U Ranch National Historic Site (CA-4774). It’s a working ranch and it takes you back to the late 1800s once you set foot beyond the gate. As I’m fairly certain the Ranch would take a dim view to radio technology beyond the gate, I operated in the visitor parking lot. Once again, I set up my cameras and gear and got to work. Continue reading A tale of two back to back activations

One CW Question series draws to a close after 6 months

by Vince (VE6LK)

Firstly, a huge shout-out and thank you to Thomas K4SWL for letting me hang out here on QRPer.com and exercise my creative writing chops, and to the community at QRPer.com for giving me such excellent feedback in my original article – both of which propelled me into this fun project.

Sometimes I begin my creative writing on a notepad with pencil, and sometimes I just type it out.

On January 20th 2024, I posted a simple question to readers of QRPer.com, If you could tell new CW learners your single best tip to learn CW, what would it be?

I was overwhelmed with the response in the comments and realized I had struck a nerve. At least one person told me that I should have bought a lotto ticket with that sort of luck, but I’ll tell you all that I am richer with the knowledge I’ve gained and shared with others as a result of the interviews I conducted with the who’s who of the English-speaking CW world.

My first key, on the right. Yes, a converted joystick. Yes, I did my exam with it.

It’s with a mixed heart that I’m here to announce that project has drawn to a close. It’s been tremendously helpful to so many people. Here’s the final episode and my personal tip to all of you aspiring CW learners.

I’m blessed to have met so many interesting people along the way and forged new friendships as a result.

Additionally, extra special thanks to Tim N7KOM, Alan W2AEW and Adam K6ARK who, along with Thomas, were my first victims interviewees where I was able to refine my interviewing and video editing process. And, Adam gave me a great idea – refine the videos into YouTube Shorts format. These refined Shorts are called 1CWQ and are the essence of each tip I recorded. The credit for the Shorts really belongs with Adam.

My entire family of keys (minus one in my truck and the others pictured above). W8BH Morse Tutor kit seen in the back of the photo. Visit my website to get your kit.

I interviewed 53 people for the series and produced well over 100 videos as a result as some gave us (you and I) more than one tip. If you missed the series, it’s not a ton of hours to binge watch. The original recordings are 2-3 minutes each and the shorts are all under one minute, or else YouTube won’t let me call them a short. You can find the Original playlist here and the Shorts playlist here.

I hope you enjoy these CW tips at least half as much as I did in recording and editing them.

One final tip, direct from my friend W5WTH who offers the following excellent advice in words better than I could ever say:

“Don’t let perfect be the enemy of good. Most CW ops are patient and can recognize a new op right away. They will most likely be happy to work you at a slow speed because they recall their personal CW journey. SKCC and POTA are the two easiest, stress free ways to make a CW QSO. Once you get the numbers and letters learned then start trying to get on the air. Don’t worry if you screw up because we all screw up and try to get better…”

I’ll add here that CW means never having to say SRI (CW shorthand for sorry) <GRIN>. Also Pat W5WTH has an excellent website too!

Handmade key left to me by VE6AB

Lastly, this is the story behind the straight key featured in all of the videos and in the main photo for this article. The key was hand crafted by my friend VE6AB, Jerry Clement, now a silent key. Jerry was a creator, maker, master machinist, backcountry hiker and camper, and photographer – a real true Renaissance Man in every sense of the word. His photography graced the covers of QST Magazine often in recent years.

At a time when CW was required for HF privileges in Canada, Jerry did his CW exam with this key and he told me once it was a real attention-getter at that testing session! Upon his passing it was bequeathed to me with instructions for me to use it and to keep my [at-that-time struggling] CW skills up. The only parts he did not manufacture were the ball bearings and the rubber feet – all of the other parts were crafted in his hands. I shall always treasure this beautiful key.

Thank you, Jerry, for encouraging me from the great beyond. DididiDahDiDah

73 and dit dit,
…Vince

First introduced to the magic of radio by a family member in 1969, Vince has been active in the hobby since 2002. He is an Accredited examiner in Canada and the USA, operates on almost all of the modes, and is continually working on making his CW proficiency suck less. He participates in public service events around Western Canada and is active on the air while glamping, mobile, at home or doing a POTA activation. You can hear him on the Ham Radio Workbench podcast, follow him on Twitter/X @VE6LK and Mastodon @[email protected], check out his YouTube channel, and view the projects and articles on his website.

Experimenting during Field Day 2024

by Vince (VE6LK)

Field Day 2024 started out with the best of plans to be spent with the best of friends and ended up totally different – and, unexpectedly, I had a hoot! With my carefully made plan behind me, my new last-minute plan was to run solo for Field Day in the backcountry of Kananaskis Country and bring along my new-to-me Nikon D3400 and lenses and rekindle my interest in (D)SLR photography at the same time as doing some experimentation with radio gear.

I grew up in a home with a scratch-built enlarger and a darkroom, so a love of taking pictures has been with me for a long time. My Father taught me patience to get the shot as he would set up a 120 format bellows camera on an air-triggered remote release to get closeups of chipmunks while we were camping, a process that took hours and yielded excellent results. My Brother, AG7GM, has attempted to instill within me the basics of composition, rule of threes and such and his wonderful skill in editing both stills and live video. While I have plenty of patience, with composition I think I’m fair to middling at best.

Thus photography has always been on my mind.

With a recent sale of a few ham radio related items, I had fun money, so just for fun I started looking [on Thursday before I activated] at used DSLRs and was shocked at how much camera I can get for such a relatively low cost compared to new. I had said once, 25 years ago when I divested out my 35mm kit, that when I could get a DSLR with a 25 to 300mm lens for <$500 I’d jump in… and finally that day is here, even if it means carrying two lenses. Of course, I started looking on the day before Field Day for deals – and scored them too! 🙂 Around these parts, good quality pre-owned consumer grade DSLRs are easily available. I purchased this as much for still photography as for ability in shooting high-quality video for my YouTube channel.

These peaks form part of the border between Alberta and British Columbia to the west

For me, Field Day has always been about the experimentation rather than chasing points. Trying new things. Changing up from the normal way I operate in the field. Comparing, analyzing and making notes as I go.

For example, and as a tribute to Chip Margelli K7JA (SK) after corresponding with his brother David, last year I attempted to wet a piece of string and see if the KX3’s tuner would match it and radiate a signal. Chip was known for many things, among them his proficiency in CW as he demonstrated on The Tonight Show with Jay Leno in 2005. David told me that he and Chip would do crazy and fun experiments like loading up clotheslines and wet string to experiment .. and it fostered a new direction I could take each FD and on some days between. The string experiment was a failure last year but I haven’t given up yet!

This year, I wanted to work with a few different antennas and a Charmast 100W battery pack from Amazon along with a USB-C PD 12v power cable for my KX3 [note: Amazon affiliate links!].

I wanted to know, in no uncertain terms, that the Charmast would or wouldn’t be as quiet as my trusty Talentcell LiFePO4 pack. The Charmast is also used in my field soldering kit with a Pinecil as it delivers USB-C PD. What better way to test this out than to head as far away from noise sources as possible, see the Canadian Rockies in their early summer glory with snow on the peaks, rivers running high (and cold) and the sun in the sky? Just for grins I would ensure that I was in POTA entities while doing Field Day.

Continue reading Experimenting during Field Day 2024