Although I’m a huge fan of wire antennas in the field, since I started using CW during my Parks On The Air (POTA) activations, I’ve really enjoyed experimenting with compromised portable antennas.

Typically, there’s a trade off with field antennas:

High-performance antennas tend to take more time to install. Some of my highest performance antennas are dipoles, doublets, delta loops, and end fed wire antennas. All of them require support from a tree if I want maximum height off the ground. Some (like the dipole) require multiple supports. While I actually enjoy installing wire antennas in trees, it typically takes me at least 10 minutes to install a wire antenna if it only needs one support and one counterpoise.

Compromised or low-profile antennas may lack performance and efficiency, but are often much quicker and easier to deploy.

In my opinion, field operators should keep both types of antennas in their arsenal because sometimes the site itself will dictate which antenna they use. I’ve activated many sites where wire antennas simply aren’t an option.

That was not the case last Tuesday, however.

Tuttle Educational State Forest (K-4861)

On Tuesday, December 29, 2020, I stopped by Tuttle Educational State Forest (K-4861)–one of my favorite local state parks–for a quick, impromptu activation.

I had no less than four antennas in my car that day and Tuttle is the type of site where I can install pretty much anything: they’ve a spacious picnic area with large tables, tall trees, and parking is close by. Tuttle is the perfect place to deploy not only a large wire antenna, but a large radio if you wish since you don’t have to lug it far from the car.

But en route to Tuttle I decided to take a completely different approach. One of the four antennas I had in the car that day was the Elecraft AX1 antenna.

Without a doubt, the AX1 is the most portable antenna I own. It’s so compact, I can carry it in my pocket if I wish.

When I first purchased the AX1, I was very skeptical and assumed it would only work when “the stars aligned”–days with better-than-average propagation and lots of POTA hunters/chasers looking for me.

The first time I used the AX1 in the field, it impressed me (understatement alert).

The second time, same thing.

In all of my AX1 activations, however, I had only operated on the 40 meter band where the antenna’s footprint looked more like a NVIS antenna than a vertical. Meaning, most of my contacts were in neighboring states like Tennessee, South Carolina, Virginia, and Georgia (typically, those states are in my 40 meter skip zone).

The reason I hadn’t tried 20 or 17 meters with the AX1 is because I would start an activation on the 40 meter band and accumulate enough contacts to achieve a valid activation. Since I’m often pressed for time, I simply didn’t bother configuring the antenna for the higher bands.

Time for that to change!

The question I wanted answered at Tuttle: could the AX1 antenna work “DX” stations? By DX, I mean POTA DX, so distant states and provinces primarily–not necessarily other countries.

Gear:

• Elecraft KX3
• Elecraft AX1
• CW Morse “Pocket Paddle”
• Bioenno 3 aH LiFePo Battery (Model BLF-1203AB)
• Ham Radio Workbench DC Distribution Panel 

On the air

I paired the Elecraft KX3 with the AX1 at Tuttle. This was the first time I’d ever tried this particular transceiver/antenna combo.

After setting up, I started on the 20 meter band and called CQ for a few minutes.

The first two stations I worked were in Texas (KF9RX and K5RX).

The third station (W6LEN) was in California.

California!?!

Honestly, it was/is hard for me to fathom how in the world 10 watts into a tabletop telescoping whip antenna could work a station exactly 2,083 miles (3,352 km)–and three time zones away–from my picnic table. I’m sure W6LEN has a great antenna on the other end, but I bet he would be surprised to learn that my 10 watt signal was being radiated by such a wee antenna.

 

 

I then worked stations in Florida (K2WO), Minnesota (N0UR), and New Hampshire (W2NR) and decided to move to 17 meters.

On 17 meters I worked W2NR in New Hampshire once again.

I should note here that each time you work a station on a different band or with a different mode, it counts as a separate contact in POTA. In other words, my contacts with W2NR on 20 meters and 17 meters counts as two logged contacts toward my overall QSO count. I’m very appreciative of hunters who go out of their way to work me on different bands and modes: those extra contacts help me achieve a valid activation in short order.

I then moved to 40 meters and worked stations from Tennessee, West Virginia, Ohio, and Michigan.

Video

Here’s a video of the entire activation. It’s a long video as it starts at set-up and continues until my last contact. There are no edits in this video–it’s a real-time, real-life deal and contains all of my bloopers:

Note that in the video I had the KX3’s volume maxed out so that it could be picked up by my iPhone microphone. The KX3’s wee internal speaker was vibrating the chassis ever so slightly. On the 40 meter band, it resonated enough that it moved the encoder slightly. Next time, I’ll plan to bring a portable external speaker (if you have any suggestions of good ones, let me know).

And here’s a QSOmap of the activation:

Bioenno 3aH LiFePo battery

I should also add that I’m very pleased with my new Bioenno 3aH LiFePo 12V battery. You can see it in the photo above–it’s slim, lightweight, and very compact.

I purchased it during Bioenno’s Black Friday sale. I was a little concerned it might not have enough capacity to carry me through multiple activations–my other LiFePo batteries re 4.5 and 15 aH–but that does not seem to be the case at all! Not only did it provide nearly an hour of intense use on this activation, but it also powered three activations the previous day–all four activations on one charge! Brilliant!

Radio magic

As I mentioned in a previous post, this was one of those activations that reminded me of the magic of low-power radio. It was incredibly fun!

For all of those phone/SSB operators out there, I will eventually see how successful I can be doing a phone-only activation with the AX1 antenna. I’ll plan to make a video of it as well. I’ll need to plan this for a day when I have more time to spend on the air and at a site where I know I’ll have internet access to spot myself to the POTA network.  SSB isn’t quite as effective as CW when operating with a setup this modest. Still–it can be done! It just requires a little more patience. Please let me know if this sort of thing would interest you.

Until then, Happy New Year and 73s to everyone!

Cheers,

Thomas (K4SWL)