Along with the Dayton Hamvention, I try to attend the Ten-Tec hamfest every year. Not only is it one of the hamfests nearest my home base, but also their “radios only” free tailgating is the source of many great quality radio finds. In the past, I’ve purchased several “boat anchors” and Ten-Tec radios at this event’s tailgating.
This year I’ll be joining the ranks of tailgaters as well, as I reluctantly part ways with my trusted OMNI VI+ in order to pay for some shack upgrades. If you come to the hamfest, be sure to stop by and say hello.
Moreover, this year Ten-Tec has invited Rob Sherwood (NC0B) of Sherwood Engineering to a speak-and-greet. I know Rob; he’s a great presenter, and you’d be hard pressed to find a guy more knowledgeable about receiver design. His free presentation will take place at 11:00 am on Saturday. (He will also host a forum Friday night at the W4DXCC–see below).
1:00 PM John Occhipinti will speak about the Ten-Tec user nets followed up with a 40 meter SSB net beginning at 2:00 PM direct from the TEN-TEC Homecoming Hamfest.
Saturday Morning Forums:
9:00 AM Learn about the new FG-01 Antenna Analyzer by You Kits (Jim Wharton, NO4A)
10:00 AM Learn what makes a quality receiver (Rob Sherwood, NCØB)
11:00 AM Learn about the many features offered with the TEN-TEC 506 Rebel (Craig Behrens, NM4T)
…and QRP @ W4DXCC
Each year, the W4DXCC coincides with the Ten-Tec Hamfest, and I always try to attend this excellent event, too. My buddy Dave Anderson (K4SV) is the new president of the W4DXCC, and does a fantastic job putting together an informative, fun event. I’ve made many friendships there over the years.
Though the W4DXCC is a DXer/Contesting convention, that definition isn’t strict, so don’t think for a moment that QRP doesn’t have a place there–! Indeed, my good friend, Vlado (N3CZ), is opening the convention with a presentation on QRPer operation. I do hope he will also display some of his homebrew QRP transceivers (one of which was built into a USB keychain!); no doubt his presentation will be very interesting.
If you’re planning to attend the Ten-Tec hamfest, consider spending the remainder of the day at the nearby W4DXCC. At $30 at the door, it’s a bargain, and I promise you’ll return home with new friends and an even better understanding of DXing. Come join the fun!
The North GA QRP Club gang have added a new annual field event to the amateur radio contest calendar–a field event with an unusual twist. The Peanut Power Sprint is this Sunday, September 29, 2013, from 2000Z to 2200Z.
What’s unusual about this event is that it is open to those operators running QRP, those running more than QRP power, those operating at home, and those operating in the field. Participants will be competing against only those who are in the same class. In addition, both CW and SSB operation are allowed and encouraged.
Operations are allowed only on 15, 20, and 40m. The recommended 40m CW frequency is 7.060MHz, not the usual QRP calling frequency.
Those operators with a “Peanut Power Number” can work anyone; those without a number may work only those with numbers. It’s not too late to request a “Peanut Power Number”.
Personally, I’m looking forward to be operating as Peanut Power #105, “Salted” (5w, portable).
It is has been a few months since we announced the FX-4 Transceiver but it is getting very close to being available for purchase. For those of you that are friends of our Facebook page or visited our booth at Dayton Hamvention got an early peek at it. Here is an updated picture and it will be a very sharp black color. Other pics are on theFacebook page. We have been making some last minute tweaks that we think you will really like. We plan to offer it for purchase under $500 and you can add your name to the wait list which can be found at the bottom of our purchase page.
FX-4 Specs
Transceiver size in inches
4.10L X 2.8W X 1.5T
Transceiver Weight
12.8 oz.
Current Drain on receive
250-270 ma
Current Drain on transmit
1200 ma
Receive/Transmit Bands
7.000.00 to 7.300.00 MHz
14.000.00 to 14.350.00 MHz
9.999.00 to 10.150.00 MHz
18.068 to 18.168.00 MHz
Frequency control
75 MHz
Display type
LCD-128×64
Transmitter Max output power
5 watts CW
5 Watts SSB
Spurious emissions
-43dB at 5 Watts
Side tone pitch
550Hz to 1500Hz adjustable
Receiver sensitivity
0.3uV
Selectivity
-3dB/ 2.6K -40db/ 4.5K
Audio Output
1 Watt with 8 ohm speaker
Keyer
Iambic A & B adjustable speed from 5 to 40 wpm
Memory Storage
10 per each Band total of 40
DSP filtering
300KHz, 500KHz. 1.3KHz, 1.6KHz, 1.9KHz, 2.2KHz, and 2.5KHz.
VFO Drift
<5Hz after 5 minute warm up at 30c (<10Hz after 30 minute operation @ 40c)
Many of you know that I’m not only into QRP, but I’m an avid shortwave radio listener, as well.
If you’re an SWLer, too, you might might consider venturing over to my shortwave radio blog, The SWLing Post, where I just published a review of the Elecraft KX3. Unlike other reviews of the KX3, this was originally written for the May 2013 issue of Monitoring Times Magazine and focuses on the KX3 as a shortwave radio receiver.
This Sunday (July 14, 2013) from 16:00-22:00 UTC, grab your QRP rig and head for the outdoors in the new SYBO (Scorch Your Butt Off) contest. According to the SYBO website, this contest is all about operating in hot weather conditions (something very easy to find this year in North America); a nice contrast to the FYBO (Freeze Your Butt Off) winter QRP contest.
Basic rules and exchange are as follows:
(Source: SYBO)
Scorch Your Butt Off QRP contest SUNDAY, July 14, 2013 1600-2200 UTC
Categories –
Single Op Field or home
Multi Single Field or home
Multi Multi Field or home
SOTA – Summits On The Air Field (not the house roof)
QRP 5 watts max CW around QRP calling frequencies 10, 15, 20 and 40 meters
One point per contact – one contact with each station per band
Exchange –
RST, SPC (State, Province or Country), Name, Power, Temperature (Fahrenheit)
at the operator’s position. Indoor stations must report Indoor temperature.
Example – 559, NJ, Larry, 5W, 85F
Multipliers –
States, Provinces and DXCC count once each band
Field Stations x 4
Alternative Power (including batteries) x 2
QRPp (less than 1W) x 2
SOTA stations – add 100 points* to their SYBO score per summit activated
* Bonus points do not count towards SOTA awards
Highest Operating Temperature (at your operating location –
Below 90 F = x1; Cool weather
90 – 99 F = x2; Break out that Hawaiian shirt
100 – 104 F = x3; Just starting to warm the rattlesnakes up
I was very surprised to find this handy talkie, the Tokyo Hy-Power XT-751 HF handheld transceiver, at the Dayton Hamvention. This radio will cover from 40 meters to 6 meters in both SSB and CW. It will also have an internal ATU. It is only a concept radio at this point.
Tokyo Hy-Power hopes to have this radio in production mid 2014.
I was more than surprised to find Palstar showcasing a transceiver at the 2013 Hamvention. Palstar is well-known for their tuners and their receiver, the R30A, but they have never sold a transceiver to my knowledge.
As you can see from the photos, the Palstar TR-30 has a simple faceplate with a touch screen display. It is all aluminum, thus is very light. TR-30 is rated for 20 watts PEP and has an 11 pole filter on board.
I hope to review one once it is in production. Palstar expects the TR-30 to be available August 2013.
(Click to enlarge)
When I asked about the price, the told me a range of $1,500-2,000 US. (Gulp!)
The TEN-TEC Model 506 Rebel 20/40 meter QRP Transceiver (Photo: TEN-TEC–click to enlarge)
Today, at the QRP ARCI convention–Four Days In May–TEN-TEC will announce a new QRP transceiver based upon a completely different platform than any others rigs they have in production: a QRP radio, built on the chipKIT™ Uno32™ (Arduino-based software) to be known as the Model 506 Rebel.
And, folks, I’ve been lucky enough to get my mitts on a prototype…!
The Model 506 Rebel
The TEN-TEC Model 506 Rebel is an open-source (meaning, anybody can program it), factory-built QRP transceiver based on a Chip Kit Uno 32 Arduino-compatible prototyping platform, which serves as the main processing unit that holds the Rebel’s program. (For those of you not familiar with the Arduino series, check out this article.)
And I have to admit, I love the concept: TEN-TEC delivers a factory-built, uber-simple transceiver, with just enough programming to reliably get you on the air with a basic radio (see details below). Users then have full access to develop and program the Rebel via an open-source platform, themselves. No need to wait on firmware revisions; firmware, in a sense, will be crowd-sourced! That’s to say, it uses online collaboration–a great idea.
According to TEN-TEC, the programming environment is very safe. Users can tinker with code without fear that they might harm their Rebel 506. The original base program can be re-flashed to the radio at any time. So if you can’t get past an error, you can always revert to a safe default copy.
In addition, even if you don’t have any idea how to program, someone has already created a web-based email group where users can upload and share code packages, and you can select someone else’s programming to test drive. Click here to join the group.
The Rebel is a CW-only transceiver that operates on 40 or 20 meters. The user changes bands by moving jumpers inside the chassis, mounted on the PC board.
The basic Rebel comes with no frequency display. When you turn on the radio, it comes up on the QRP calling frequency of 7.030 MHz or 14.060 MHz, depending on which band is selected. There is no VFO, but a DDS chip that is highly stable and that allows the Chip Kit Uno 32 to select a frequency upon which to operate. Of course, since the Chip Kit controls the DDS chip, you can re-program how the Rebel manages frequencies.
(Click to enlarge)
Initial impressions
Last week, TEN-TEC sent me a prototype of the Rebel to Beta test. I’ve had it on the air several times–I’ve also popped the cover and given it a thorough inspection and workout. I’ll share my initial impressions below. I’m not commenting, however, on some specs like filtering, as they have not been finalized for production and are still subject to change. The unit I tested, keep in mind, was a prototype; production units will be still more polished and incorporate changes Beta testers have provided.
(Click to enlarge)
Front Panel Layout
The front faceplate of the Rebel 506 is reminiscent of TEN-TEC QRP Kits, gloriously clean and simple. There is a large tuning knob in the middle with a SELECT button on the left and FUNCTION button on the right. Both buttons are large enough that you could comfortably use them even if wearing winter gloves. Above each button is a vertical row of just three LEDs: green, yellow and red. These colored LEDs simply indicate the position of the function/selection buttons.
(Click to enlarge)
Function button controls
Band Width
Step Size
User-programmed functions
Select button selects
Bandwidth: Wide, Medium and Narrow
Tuning steps: 100 hz, 1 kHz or 10kHz
User, U1, U2 or U3
There are only two knobs: one for volume (AF gain) and one for RIT (+/- 500 Hz). There is also an ON/OFF simple toggle switch, and a rather classy touch from TEN-TEC–namely, a small LED light in the TEN-TEC logo itself. And that’s all, folks–bare-bones design.
No frequency display
The Rebel 506 does not come with a frequency display. However, there are features to help you understand where you are on the band as you turn the encoder:
As you tune within the selected tuning steps, the LED in the TEN-TEC logo flashes as you pass each step; for example, if you’ve selected 100 Hz steps, then when you pass each 100 Hz step, the LED in the logo will flash once. When you reach either band edge, the LED stays lit. Again, a nice touch.
When you turn on the (factory default) Rebel, the frequency starts on QRP calling frequencies 7.030 MHz (40M) or 14.060 MHz (20M)–of course, you could change these with programming.
There are (already) third-party frequency displays that plug into the Rebel’s board, an easy addition.
Since I had neither frequency display nor frequency counter, I simply used my SDR’s waterfall display to locate where I was on the band. It’s also fairly easy to count the steps with the logo’s red LED.
Rear view (Click to enlarge)
Connections
On the rear panel, you’ll find a standard BNC antenna connection, a key/paddle port (1/8″), a speaker/headphone port (1/8″) and a standard DC port (10-15V reverse polarity protected) that equates to 4-5 watts output depending on supply voltage.
Key/Paddle input from the factory is only for straight key, but you can modify the code to make it a paddle input. Also, the headphone/speaker port defaults to headphone use from the factory, but there is a small jumper on the PCB that can me moved to drive a non-amplified speaker.
On production units (not on my prototype, however, nor on those at FDIM) there will be a CW side tone volume control pot via a small hole in the side of the Rebel’s enclosure. Also, production units will have a hole on the rear panel to allow for access to the ChipKit’s USB port.
The PCB has hooks, test pins, and inputs for the following:
Battery read pin: reads 0.20 of the supply voltage.
Power-out read pin: reads 0.50 of the RF pickup
Code read pin: ties to low level audio line, can be used to build a CW code reader
CW-speed read pin: DC voltage used to determine approximate speed of CW routine
All connections of the Chip Kit Uno32 are available on the top of the PCB.
The unit accepts Arduino-compatible Shields for such things as:
Prototyping
Displays
Audio DSP
Evidently, the Rebel has a lot of memory space for writing CW memory-keyer functions or whatever the user desires/dreams up. Even a voice synthesizer could be installed in the Rebel; indeed, I believe there are many mods and possibilities for the Rebel. The greatest limitation might simply be…the imagination of the user.
TEN-TEC was clear with me about the goal of the Rebel 506: “To provide a platform for users to experiment and to learn to program using Arduino-Compatible Code.”
The Rebel has a small form factor (Click to enlarge)
I like it!
I have thoroughly enjoyed putting this little radio on the air. Let’s be clear, though: this is no Argonaut VI or Eagle, nor should it be expected to be. Receiver performance is on par with other QRP kits and rigs of its class. The Rebel is fairly sensitive and the noise floor is fairly low. Selectivity is adequate for most conditions, although I imagine crowded conditions could overwhelm this modest receiver.
When I had the Rebel on the air, I engaged in a bit of a rag-chew and found the audio quite pleasant from my GoalZero portable amplified speaker. And other than needing to adjust the side tone volume, the Rebel was ready to go, straight out of the box.
Criticisms? Well, it’s just too early to have many. I’ve passed along all my frank observations to TEN-TEC and they’re actually addressing them now (yet again, one of the many benefits of an American-based radio producer). If this were a $900 rig, performance-wise, I would complain about selectivity. But I’m willing to bet it’s at least as good as the Index Labs QRP ++ I once owned. In fact, though it’s not a full-featured general-coverage rig, it has that same sort of bare-boned fun factor the Index Labs radio provided me, along with many other QRP kits.
Field? I would totally take the Rebel into the field or backpacking. I have a hunch it uses less than 200 milliamps on receive. It’s modestly-sized and built like a little tank.
The Rebel lives up to open-source philosophy
The Arduino chipKIT Uno32™ Prototyping Platform
Here is the amazing part about the Rebel: TEN-TEC only shipped me the radio–no connectors, no adapters, no power cord. At first, I thought I’d have to find an appropriate plug and solder my own power cord, not to mention figure out what other adapters I would need for my key/speaker…but I didn’t. The power port is very standard; the same one my LDG ATU, Elecraft K2 and KX1 use, with standard positive tip polarity. The Rebel’s antenna connector is a BNC, speaker and key ports are standard 1/8″ and the ChipKit board has a mini USB connection. The top cover is easy to remove–even the toggle switch, LEDs and selection buttons are all standard and easy to access for servicing. Everything is standard!
But it doesn’t stop there. The Rebel is truly an experimenter’s radio, and is meant to be. The programming is completely open-source and TEN-TEC is encouraging and facilitating users to tinker with the code and make hardware modifications at will.
Open-source technology is all about alteration and collaboration, the kind of environment we hams have always embraced. In the open-source world, nothing is proprietary; rather, everything is transparent, standard, accessible; supporting changes and modifications of every stripe. And in my humble opinion, it’s about fun. On these points, the Rebel delivers.
I have done some scripting in my past, but I am no professional programmer. Though many of my Maker friends had been urging me to give it a go, I hadn’t jumped on the Arduino band wagon until, well, now. The Rebel will serve both as a great intro to Arduino Compatible Code and a truly fun QRP rig. If TEN-TEC is lucky, this little rig may actually nudge some of my Maker friends to get their ham radio tickets.
(Click to enlarge)
Price
TEN-TEC will be announcing the price of the Rebel 506 in Dayton, literally in just a few hours. I have no idea what it will be, but I’m fairly sure it’ll be competitive with other dual band QRP transceivers and kits on the market. I’ll post an update here when the price has been published. Stay tuned…
UPDATE: Pricing for the Rebel is $199 US.
By the way, if you’re at FDIM or the Hamvention this year, drop by booth 411 in the Ball Arena: I’d be happy to talk with you about the Rebel further (and my radio-based non-profit, Ears To Our World).
Disclaimer: Just to be clear, although I own TEN-TEC (also Elecraft and Yaesu) products, and although I Beta test for TEN-TEC on occasion, I have no formal relationship with TEN-TEC. Nor am I compensated by the company in any way. The opinions in this article and others on this site are frank and my own; they are not those of TEN-TEC.
One of the highlights of my trip to the Dayton Hamvention last year was attending evenings at Four Days in May (FDIM), a QRP convention sponsored by the QRP ARCI that rather conveniently coincides with the Dayton Hamvention, which I try to attend annually. Though scheduling makes it difficult for me to attend all of FDIM’s daytime presentations, the camaraderie and innovation one discovers at the evening sessions is wholeheartedly worthwhile.
Last year, I snapped quite a few photos at FDIM which I planned to post following the Hamvention. Unfortunately, shortly after the Hamvention, my laptop began displaying signs of an early demise. In haste, I archived my photos on a portable drive, where they remained buried for a year. I just rediscovered this photographic treasure, and thought I’d share it with readers; looking through them rekindled my enthusiasm for FDIM 2013, which starts next week!
A quick look at FDIM 2012
A great characteristic about FDIM is the array of QRP products offered by QRPers for the community. More often than not, these products are fairly priced, and often in support of the QRP community rather than major profit-making ventures.
For example, the North Georgia QRP Club produces affordable wood stands for QRP rigs. They’re incredibly simple, but fully finished and beautifully designed, just the thing to prop up your QRP portable at the right angle for desktop use.
Speaking of wood products–one vendor last year featured an amazing array of wooden paddle pieces and even custom wooden tuning dimples (spinner knobs) for the Elecraft K2 and K1.
As you can see from the photos, each piece is perfectly finished and has great character, as one might expect of real wood.
Dennis, being a hard-core QRPer, trekked with ham gear in tow; he brought his kits to FDIM:
There were a variety of keys and paddles to be seen, of course; offerings range from the home brewed to gorgeous Italian Begali designs:
One paddle that really caught my attention was QuadraBug, a creation of WB9LPU. What makes this gem stand apart from other “Bugs” is that not only will it form “dits” automatically, but it also forms “dahs.” Truly, an amazing work of engineering. I searched the web for a video of the QuadraBug in action, but found nothing. [UPDATE: Thanks, Yan for finding a video! See video below.] This year, I’ll take a video if I’m fortunate enough to see it again.
Home-brew galore
There were an amazing number of home-brewed projects on display, and even a home-brew contest. I didn’t capture photos of them all, but I did manage to snap a few.
One that really caught my eye (being a shortwave receiver enthusiast) was David Cripe’s (NM0S) version of Hutch’s Radio. The original Hutch’s Radios were built by US and British POW’s in WWII. Built in canteens, often from confiscated parts, these radios gave POWs hope by allowing them to tune in the outside world, via the BBC WS and Voice of America. In the spirit of the original, David challenged himself to build his version prior to FDIM, with original parts of the era, and in “secrecy.” Secrecy? As many of the components had to be purchased from suppliers on eBay, David tried to intercept all of the incoming packages without his wife noticing. His success was brief–alas, his wife discovered the mission–but fun; still, the end result was a very cool piece of historical recreation with a humorous story to match:
Of course, FDIM featured loads of QRP transmitters, receivers and transceivers; here is Dwayne’s (AK4P) 40 meter transceiver, built in a SPAM container:
Terry Young, K4KJP, built a very cool pocket 20 meter transceiver in an Altoids tin:
And Alan Shapiro, NM5S, should have won a prize for the most compact set of CW paddles. These paddles are so small that they can be clamped onto your log book. Much to my surprise, they were amazingly easy to use, and would be a great addition to any field-portable radio:
FDIM 2013
If FDIM 2012 is any indication (yes), this is a mere sampling of the stuff you’ll see at Four Days In May 2013. I encourage you to attend: if nothing else, make a little time either Thursday, Friday or Saturday evening to visit the evening displays at FDIM–they’re free and open to the public.
If you can’t attend, I hope you’ll earmark your calendar for a future date. I do plan to bring my camera again this year and will share some photos. Hopefully, I’ll post them a little earlier this go-around!
Hope to see you at FDIM and the Hamvention. For the third year in a row, I will be representing my charity, Ears To Our World (ETOW), at an inside exhibit at the Hamvention. We should be in booth 601 in the East Hall. Please feel free to stop by and introduce yourself! (And if you feel so inclined, you can even donate a few bucks to our worthy cause.) See you there–!
When the band is open, 10 meters is the band for QRP DXing–great DX can be worked with very low power and very modest antennas.
The entire world congregates on 10 meters on the second full weekend of December for the ARRL 10 Meter Contest. This year this contest falls on the weekend of December 8-9, 2012. Complete rules can be found here: www.arrl.org/10-meter. It is worthwhile to note that this contest allows participation by both CW and phone operators.
We are approaching the peak of sunspot cycle 24 and conditions on 10 meters should be excellent for working DX. Even those not interested in the contest per se should take advantage of the propagation and the sheer numbers of DX stations on the band to work some “new ones”.
Connecting an international community through low-power field radio adventures.
Please support QRPer by adding us to your whitelist in your ad blocker. Ads are what helps us stay online. All of our ads are ham radio related--no junk, we promise! Thank you!
Along with the Dayton Hamvention, I try to attend the Ten-Tec hamfest every year. Not only is it one of the hamfests nearest my home base, but also their “radios only” free tailgating is the source of many great quality radio finds. In the past, I’ve purchased several “boat anchors” and Ten-Tec radios at this event’s tailgating.
Each year, the W4DXCC coincides with the Ten-Tec Hamfest, and I always try to attend this excellent event, too. My buddy Dave Anderson (K4SV) is the new president of the W4DXCC, and does a fantastic job putting together an informative, fun event. I’ve made many friendships there over the years.
This Sunday (July 14, 2013) from 16:00-22:00 UTC, grab your QRP rig and head for the outdoors in the new SYBO (Scorch Your Butt Off) contest. 
