Tag Archives: Nemo Moonlander Portable Table

Field Reports, Morse Code, News, Portable, POTA, QRP, Stealth, Travel, Videos

Tough Bands, Tiny Antenna: An AX1 Activation at Fort Wellington NHS

July 1, 2025 Thomas Witherspoon 8 Comments

Note: This first field report from my 2025 trip to Canada happens to coincide with Canada Day (today, July 1, 2025). Happy Canada Day!

by Thomas (VY2SW / K4SWL)

In a previous post, I mentioned that my family was heading north into Canada for a few weeks this summer. This trip wasn’t easy to carve out of our schedule, but we were looking for a bit of escape from all of the Hurricane Helene clean-up—and, frankly, we were craving some family time.

We arrived in Canada (via the Thousand Islands Bridge) on Saturday, June 14, 2025, in the late afternoon. Had it not been such a tiring drive that day, I would have activated Thousand Islands National Park (CA-0099), but honestly? We were all ready to check into our hotel in Brockville, Ontario, take a stroll along the waterfront, and grab some dinner.

The next morning (June 15, 2025), I took a look at the POTA map and determined that we had plenty of time for a park activation before heading into Québec. Several options lay along our route, but one, in particular, caught my attention:

Fort Wellington National Historic Site (CA-4868)

Fort Wellington is a Parks Canada site situated right along the St. Lawrence River, which we were traveling beside. Even better, it was only about a 15-minute drive from our hotel.

We arrived on-site around 10:15 AM local time and immediately noticed the parking area in front of Fort Wellington was barricaded for an event. I saw two Parks Canada rangers standing out front, so I asked them about the event and whether it was okay to park on the street in front of the property. They couldn’t have been kinder.

Turns out, the town was hosting an outdoor BBQ ribs event that Sunday. It’s as if they expected a ham from North Carolina to pick their site for POTA! It was a pretty big event for a town as small as Prescott—there were loads of entertainers, food trucks serving all forms of BBQ, and tours of Fort Wellington.

I asked the rangers if they were familiar with Parks On The Air (they were!) and if I could set up on the NHS property closer to the river and away from all the festivities. They gave me permission.

I should add here that I volunteered not to put any antennas in trees or place stakes in the ground to mount my telescoping carbon fiber pole. As a rule of thumb, I default to my lowest-impact setups when at archaeological or historic sites. I feel it’s not only respectful but also leaves a good impression of ham radio operators for park staff who may encounter activators after me.

My wife and daughters were encouraged to take a free trolley tour of Prescott—how could they resist? They told me later that it was a hoot.

I made my way down to a shady spot under a tree by the river.

To keep things low-impact, I set up my Nemo portable table and Helinox chair, then deployed my KX2/AX1 field kit.

I’ll be honest here…

Propagation had been very rough the previous day, and numbers were indicating challenging conditions during my activation as well. This wasn’t a day I’d normally opt for my most compromised antenna, but here we were. My hope was that I could call CQ on every band possible using the AX1 and somehow gather enough contacts (10 total) to validate the activation.

Backpocket strategy

So here’s the deal: most of us activators aim to get the minimum number of contacts in order to complete a valid activation (10 for POTA, 4 for SOTA).

When I’m activating a park I’ve done numerous times before? I honestly don’t care if I don’t reach 10. I’m just happy to get outdoors and play radio. I try not to let the threat of poor propagation stop me.

However, when I’m activating a new-to-me park, I really want to validate it. I want those 10 contacts—and I’m willing to spend more time on the air to get them.

Technically, since I’m traveling with three other licensed hams (my wife and daughters) and we have two dual-band HTs in the car, I really only need to make four HF contacts. I could make three FM contacts on 2 meters, then three more on 70 cm with my family. That gives me 10 total.

In fact, I also have multiple HF radios and dummy loads in the car, so I could get away with never deploying an antenna at all—I could just log 10 park-to-park contacts with my family.

But where’s the fun in that, right?

Actually, I say that, but it can be fun—in situations where you’re left with no other options—to do P2P contacts with your own crew, as my buddy Vince proves here.

Still, I was determined to log “my ten” all on the HF bands, using five watts into my 4’ AX1 antenna.

The only way to find out if I could? Hit the air!

Gear

Note: All Amazon and eBay links are affiliate links that support QRPer.com at no cost to you.

Logging Pad/Pencil

Chair/Table

Camera/Audio Gear

DJI OSMO 4 action camera with Joby Telepod Sport Tripod

On The Air

As expected, propagation was rough.

I started calling CQ POTA on 20 meters—the band I knew would likely give me the best chance. Continue reading Tough Bands, Tiny Antenna: An AX1 Activation at Fort Wellington NHS →

Field Reports, Morse Code, News, Portable, POTA, QRP, Videos

Moonlander to the Rescue: A Tabletop FT-818 POTA Activation on the Blue Ridge Parkway

June 27, 2025 Thomas Witherspoon 4 Comments

On Friday, May 23, 2025, I had a good 90 or so minutes to play radio, and the Blue Ridge Parkway (as always) is the easiest hit for me when running around in the Asheville, NC area.

I was in the western part of Asheville, though, so I needed to find a site to set up. I’d packed my Yaesu FT-818, which is very much a tabletop radio (compared with, say, my Elecraft KX2 or KH1). A picnic table would have been ideal, but there are no sites on the BRP with picnic tables in the western part of town.

I could have driven a bit further to Lake Powhatan, but it would have cut 20 or so minutes out of my activation and I’d rather opt for more time on the air than the convenience of a picnic table.

Fortunately, I packed a secret weapon—one I’d taken to Hamvention weekend and was still in the car…

The Nemo Moonlander Portable Table

Moonlander with extension legs (Photo by Nemo)

There’s a story behind this table.

Back in November 2023, when we were recording the “Holiday Shopping Show” on the Ham Radio Workbench Podcast, my dear friend George (KJ6VU)—who shares a passion for quality gear—suggested that I invest in a Nemo Moonlander portable table [note: QRPer Amazon affiliate link].

I’ll be honest: I had some credit either on Amazon or REI (I can’t remember) and decided to make the purchase based solely on George’s recommendation.

This was a splurge since the Moonlander costs around $150–180 US (!!!), depending on the color variation. When I purchased mine, I believe I paid about $160. In my book, that’s a lot of money for a portable table.

George’s selling point was that it’s the only portable table he’d used that was actually super sturdy and functional. The table surface is strong, the table has two heights (with and without the legs installed), and it folds flat. It’s not super lightweight like some portable table options on the market, but it is adaptable and useful.

When I received the Moonlander, I was very pleased with the design: it was everything George had described. The surface is so strong I could put a heavy object on it and the table wouldn’t buckle. The table, if anything, feels over-engineered. I like that.

The hinges and leg storage is beefy (Photo by Nemo)

Thing is, though, I hardly ever thought about taking this little table out to the field with me with POTA or SOTA in mind. We used it a bit for family picnics, but I tended to default to my smaller portable radios combined with a kneeboard to play radio in the field where there are no picnic tables or benches to set up.

In fact, I believe the first time I used this little table in a field radio outing was this past December (one full year after I’d purchased it) for this Christmas Eve video.

During that outing, I only used the table to hold my coffee and some Christmas cookies. I still used my kneeboard to hold my KX2.

I realized during that outing, though, that the height of the Moonlander table—with the legs installed—was about perfect for the height of my much-loved Helinox backpack chair. With it set up next to the chair, it was a great ergonomic height for me to reach things on the table.

Two months later, in early February, I took the Nemo Moonlander to the field and thought I’d experiment with using it to hold my radio and key. For some reason, I can’t find this field report or video in my archives (I’ll need to check my hard drive once I’m back from my Canada travels). Here’s a photo from that activation:

This activation taught me that the Moonlander is actually incredibly functional and gives me the flexibility to use my larger portables like the TR-45L, Argonaut V or VI, K2, RGO One, or my FT-818 (the subject of this field report) a proper place to operate.

I had not recommended the Nemo Moonlander up to this point on QRPer.com because I felt like it was just too pricey for something that had limited utility for field radio operating. My mind has completely changed on this point, though! Yes, it’s very pricey and, yes, I’m sure there are cheaper third-party knock-offs of this design already, but I’m very pleased with this purchase. I feel like the Moonlander will last me the rest of my days. The folding design is so clever. Check out this from Nemo showing the components and how it can be set up:

In short, I’ve really done a 180 here: the Moonlander—very much an impulse purchase at the time with a touch of buyer’s remorse—has become one of my favorite field accessories.

Back to our field report…

I drove to a site on the Blue Ridge Parkway near the bridge that crosses I-26 where there’s an easy pull-off and parking spot for a few cars. I’ve activated this particular site at least once before.

I walked into the woods perhaps 10 meters and started setting up my table and radio gear.

I was in a bit of pain that day, and I mention this in the video because I was a little concerned I might have difficulty sitting in my hiking chair so close to the ground. The previous evening, when walking to my neighbor’s house on a path in the woods, I slipped on a large white oak trunk. I landed on the right side of my chest on the log. The pain was significant enough earlier the next morning (the day of this activation) I set up an appointment at my doctor’s office and they made a few chest x-rays. Fortunately, it was just bruised ribs. Also fortunately, it didn’t cause me too many problems during this activation—I just had to be careful how I moved about.

I set up the Yaesu FT-818 in short order and deployed my end-fed half-wave antenna knowing that it would give me good coverage sans ATU on the 20 and 40 meter bands.