Scott’s Icom IC-705 “Shock Box”

Many thanks to Scott (KA9P) who writes:

Enclosed are a few detailed pictures of the system I’m using to protect my Icom IC-705 in the wild.

I wanted a system that would protect the radio from shock and vibration when I dropped it in use, or tripped over a cable, as well as when in transit.

Some research lead me to Sorbothane, a commercial vibration damping material available in small lots on eBay, and to a Sorbothane applications engineer. The engineer recommended that a good way to protect electronics is to use a “box-in-a-box” concept where the equipment resides in an inner box with vibration dampers between the inner box an outer box.

Sorbothane’s on-line calculators suggested that for the IC-705’s weight, some relatively small pads on each wall would be adequate.

So I started with the bottom 4.5 inches of a Harbor Freight ammo box, and added four 1/4 inch thick, 1 inch by 1 inch Sorbothane pads to the bottom and two long sides.

Then I added an aluminum plate to the inside side surfaces of the pads, and lined the plates with neoprene (see the drawing above). The neoprene adds a bit of additional padding, but primarily lets the 705 slide into “the inner box” while putting a little bit of pressure on the pads. The manufacturer recommends a slight loading pressure on the pads for proper damping.

The radio is fastened into the box with an adjustable depth 1/4-20 threaded locking knob, positioned to put a little force on the back wall vibration pads when tightened down.

The cover is made of aluminum angle stock and Lexan, and provides good protection for the front of the radio when not in use.

This “shock box” solves a lot of problems for me.

1) I can leave the cage on when operating, using dongles out the front for things I want to change like the antenna, mic, battery power, headphones or paddles. Leaving the radio in the box avoids field handling errors, to which I am prone.

2) If the internal battery needs to be changed in the field the radio comes out quickly by removing the single 1/4-20 knob and screw. But the battery can be charged in the case with a USB or power plug dongle, again avoiding handling.

3) The depth of the box protects the entire periphery of the radio front, much like the handles do for the sides of a cage, and the radio remains enclosed/covered on all sides except the front. I’ve used it in snow and rain without issues when the wind isn’t bad.

4) Impact protection is really high other than for a direct frontal panel hit within the box. The plastic box takes the first hit, deforming a bit and transferring the rest of the energy to the vibration damped inner box. Not worried about dropping the radio anymore.

5) The use of Sorbothane’s “box-in-a box” with vibration pads concept leaves a channel surrounding the radio to promote air flow and heat dissipation. For me this is much better than using the radio in a box cushioned with foam, which blocks air flow and can trap moisture.

6) The box provides a handle, which the 705 really does need in the field.

7) The footprint of the Harbor Freight box is just about a hand and glove fit in the bottom of most serious packs, making it easy to carry when backpacking.

On the downside, it’s a bit ugly, but it’s cheap, maybe $40 US to build. Other than wanting a gasket to provide better weather and dust proofing when closed, I’m happy with it.

-Scott (KA9P)

A bit ugly? Scott, I think it looks great!

I feel like shock absorption is one of the things lacking in many of the IC-705 cage solutions out there. I always feel like when a metal/aluminum frame is paired with a hard plastic chassis, in a field drop the plastic will be the weak point. 

This adds to the bulk of the IC-705 (in terms of overall size) but likely doesn’t add a lot of extra weight. In your manpack/chest pack situation, this is a great bit of engineered insurance for your $1300+ rig!

Thank you for sharing!

3 thoughts on “Scott’s Icom IC-705 “Shock Box””

  1. Yes the box would protect the IC705 if dropped, but not very good for using/operating the rig. How do you connect accessories like key, head phones, antenna, power, etc. I guess need to remove the rig for these connections.

    I have the WindCamp case for my IC705. Protects all around except front of course, but does have front handles giving some protection. Also allows access to the connectors. Others have the Pievo version, but to get it with full all around protection cost $280, is 2 piece case sold separately.

    I do carry my IC705 in suit case type case with foam cut out inside. Also has the accessories, all except the antenna.

    How one carries one IC705 depends on your type of operation. Some like foot back pack operation, some like me on a picnic table or on my home station bench. But this is me.

    One can get a custom to the IC705 a case with compartment for the rig and all connections are brought out to the panel in the box. Is nice except does not provide for many accessories. I did add foam to the top and bottom to secure the panel and IC705. Just open connect antenna and begin making QSOs.

    73, ron, n9ee

  2. Looks like a great way to protect the IC-705 — while traveling and operating!

    To protect my IC-705, I have been using an Outdoor Research brand “water bottle parka” sized to fit a 1 liter Nalgene canteen. The “parka” is insulated/padded and intended to keep a canteen of water from freezing in the winter. The IC-705 fits in it perfectly! The rig is protected in my pack while I’m going to a POTA activation — especially the touch screen.

    These water bottle parkas can be found at many outdoor stores online.

    73, Nat

Leave a Reply to Ron Wright, n9ee Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.