Tag Archives: CR Kits

From idea to kit: Adam introduces the Arduino Digital Modes HF QRP Transceiver (ADX-S) kit

Many thanks to Adam (BD6CR) who shares the following guest post about his latest project:

From Open Source Project ADX to Kit ADX-S

by Adam (BD6CR)


Original Design: WB2CBA

Modification and Kitting: BD6CR

I knew Barb, WB2CBA from his uSDX design a few years ago and I introduced both DL2MAN and his designs in my blog. So, when I came across the ADX – Arduino Digital Xcvr a few months ago, I immediately ordered both the ADX (through hole) and the ADX UNO (surface mount) PCB samples.

I started building the ADX UNO and put it in a dental floss case and made a few contacts on park bench. However, the soldering is too much for my eyesight. So, I turned back to the ADX because I don’t need to solder any SMD parts, since both the M328P and SI5351 are module based. I could build the project in 3 hours and it worked the first time.

However, I felt unsatisfied with the strong BCI since the CD2003 radio receiver chip was connected as a direct conversion receiver. JE1RAV mentioned in his QP-7C modification project that he tried JA9TTT’s idea to build a superhet SSB receiver with the TA2003 or CD2003, so I tried and it worked very well. I have decided to name the new circuit as ADX-S, where S stands for Superhet.

I shared the great news with Barb and he encouraged me to carry the flag to make it a kit, since my design D4D was his first digital radio and he loved it.

You can refer to Barb’s page on ADX here.

My hardware modification can be outlined in this schematic. I have added an FL1, PFB455JR ceramic filter by Murata and a C25 coupling capacitor from CLK2 of SI5351 module. The RX audio comes from pin 11 instead of pin 4.

I modified it by cutting two traces on the ADX PCB and it looked ugly, so I redrew the PCB. Continue reading From idea to kit: Adam introduces the Arduino Digital Modes HF QRP Transceiver (ADX-S) kit

FT8 transceiver kit: CR Kits taking orders

The CR Kits DSB Transceiver prototype (Source: CR Kits)

Many thanks to Pete (WB9FLW) who writes:

Adam of CR Kits is now taking orders for his FT8 Transceiver Kit and the price is very reasonable.

From Adam at CR Kits:

FT8 transceiver kit

I start to take email order now. The introductory price is 39 USD for kit including shipping to worldwide. As in the introductory period, you will get audio cable options for free. The earliest possible shipment date is now improved to May 13.

You can directly PayPal to [email protected] and let me know 40m or 20m (80m not ready yet). I will ship based on the sequence of receiving your payment. I may delay shipment for one week or two due to workload.

This is the spec so far:

Summary: Crystal controlled single frequency DSB transceiver for 20m (14.074MHz), 40m (7.074MHz) or 80m (3.573MHz), other frequencies could be added per requestPower supply: 10-14V DC regulated power supply or battery pack, 12V is recommended, center positive, reverse polarity protection availableCurrent consumption in RX: about 15mA at 12VCurrent consumption in TX: about 300mA at 12VRF output: about 1W for 40m band at 12V, and a bit less for 20m bandSpurious suppression: no worse than -50dBcAntenna connector: BNC connector, 50 ohmAudio in connector: 3.5mm mono, at least 600mV to activate VOX, connects to headphone connector at PC sound card, no dedicated PTT connector is requiredAudio out connector: 3.5mm mono, connects to microphone connector at PC sound cardAmber LED: TX statusGreen LED: RX statusFrequency accuracy: -600 Hz ~ + 200 HzFrequency stability: Okay for FT8 mode per test. If the optional heater resistor R20* is added, after warm up, long term frequency stability in 10 min will be improved at the cost of acceptable short term frequency stability sacrifice in 30 sec.
Thanks, Adam

Click here to check out the FT8 DSB Transceiver via CR Kits.