Pairing the Chameleon CHA LEFS with the Discovery TX-500 at Table Rock Fish Hatchery

Last time I visited Table Rock Fish Hatchery–this activation–it was a struggle to get the ten contacts I needed for a valid activation. Propagation was horrible that day, making it a proper struggle.

On Thursday, May 20, 2021, I thought I’d go back to the fish hatchery for another try! I really like the site: it’s open, has lots of trees, and the staff (and neighborhood dogs) are all very friendly.

My not-so-QRP diesel truck!

Thing is, as I drove to Table Rock, my buddy Mike informed me that propagation took a nose dive. Earlier in the day, it had been reasonably stable, but he noted that POTA activators were struggling in the afternoon and the propagation numbers were in the dumps.

There’s a beautiful little creek next to the picnic area.

My secret weapon: The Chameleon CHA LEFS

Shortly after I posted my “unboxing” video of the lab599 Discovery TX-500, Carl at Chameleon Antenna made a comment on my YouTube channel that he was going to send me their CHA LEFS (Lightweight End Fed Sloper) wire antenna since it’s resonant on 40, 20, 17, 15, 12 and 10 meters. In many ways, it’s ideally suited to pair with the TX-500 since this transceiver lacks an internal ATU. Side note: there is a cool project in the works called the DIY599 that adds a 60 watt amp and ATU to the TX-500 . 

I had only recently received the CHA LEFS and had not yet taken it to the field. Table Rock was the perfect opportunity.

When I know in advance that propagation is poor, I try to make my portable set up as efficient as possible, so that’s when I 1.) make sure I pull out a resonant wire antenna and 2.) use a wire antenna with longer radiators. The CHA LEFS fits both of these bills.

The CHA LEFS has a 63 foot radiator made of 20 gauge PTFE antenna KEVLAR wire. The winder has a large efficient transformer to match impedance, and there is an inline coil to make the most of the 63′ radiator. They also include 50′ of Micro 90 paracord.

 

Like all Chameleon antennas I’ve used, it’s built to military specs.

Table Rock Fish Hatchery (K-8012)

Table Rock is ideally-suited for a long-ish sloping wire antenna, too. The site has tall trees and open spaces that make stretching out the sloping radiator quite easy. Just watch those power lines!

The CHA LEFS takes longer to deploy that end-fed antennas with a feedpoint near the ground. I find it quicker to deploy, however, than dipoles.

I deployed the LEFS by first stretching out its radiator wire in the direction I planned to deploy it.

Next, I connected the coax feedline to the SO-239 on the LEFS winder and stretched it in the opposite direction of the radiator. Why do this? It helps keep the radiator and coax from twisting together as I raise the winder/feedpoint into the tree.

This is not a difficult antenna to deploy as one person. Of course, if you have a helper, it’ll go even faster (I’ve yet to convince Hazel to help me with antenna deployment).

I had launched the arborist line quite high into a tree at the picnic table where I planned to operate. I was able to elevate the LEFS feedpoint/winder about 47′ into the tree.

I used the supplied paracord to attach the radiator to a nearby branch. The end of the sloper was perhaps 6 feet off the ground (if memory serves).

Gear:

On The Air

Knowing how poor conditions were from real-life K8RAT observations, I didn’t expect to actually validate my activation by logging the required 10 contacts. As I stated in my activation video, I was fully prepared to walk away with three or four contacts–I didn’t have a few hours to burn on an activation. I was simply happy to play with a new antenna, the TX-500, hang with the local canine welcome committee and enjoy the fine weather.

First, I hopped on 40 meters and discovered the LEFS provided a perfect 1:1 match on 7063 kHz. Very promising!

Next, I started calling CQ and the Reverse Beacon Network functionality of the POTA spots page must have quickly auto-spotted me.

Within 13 minutes, I logged six contacts! I was impressed. Mike (K8RAT) was in that first six contacts and he later told me it was one of the strongest signals he’d ever heard from me at a POTA activation. He asked what I was using as an antenna that day and said, “it was working!”

Next, I moved to the 30 meter band and worked K8RAT again (a rarity on 30 meters!) along with four other stations.

I ran out of time, so called it quits with 11 stations logged.

I did not expect to not only walk away with a valid activation, but to have completed it in such short order.

QSO Map

Here’s the QSO Map of my contacts all made with 5 watts of power:

Video

Here’s my real-time, real-life, no-edit video of the entire activation. Next time I take the LEFS out, I’ll try to remember to include setting it up:

Loving the CHA LEFS!

Talk about good first impressions!

As Carl suggested, I’m going to keep the CHA LEFS tucked away along with my PackTenna EFHW in the Discovery TX-500 pack.

When conditions are poor, I’ll spend the modest amount of extra time deploying this fine antenna.

The only CHA LEFS criticism I noted–and it’s a minor one–is that the in-line trap/coil isn’t very low-profile and takes a little attention to make it fall in the right spot when reeling the antenna up post-activation. Seriously. A minor criticism and I’m guessing Chameleon has a reason for it being on the large size–likely for power handling reasons.

Field Day is coming up, and I think I’m going to make the CHA LEFS one of Team Baklava‘s main antennas (Team Baklava = my buddy N3CZ and me!).

As for the CHA LEFS, I highly recommend it!

8 thoughts on “Pairing the Chameleon CHA LEFS with the Discovery TX-500 at Table Rock Fish Hatchery”

    1. Absolutely! In fact, it would pair with other great QRP rigs that lack an internal ATU like the FT-818/817 as well.

  1. Enjoyed you video and written comments. Now about the local canine welcome committee. Have they been in another one of your videos as well?
    As to the CHA LEFS being Mil Spec it’s going to be well built.
    Looked up the asking price and my hair fell out, lol.

    Thanks again for your great videos .

    Robert

    1. Chameleon product are pricey–that’s for sure. 🙂 With that said, I feel like each one of there antennas will outlive me. They’re insanely over-engineered and Chameleon only uses the best components. Plus, they’re a product of a US manufacturer, so you’re paying US labor on top of military-grade materials/components. I feel like it’s worth it, if you can afford it and want to support the company. Of course, all of the wire antennas can be homebrewed for much less and I have an appreciation for homebrew gear!

      The local canine committee is the video from my previous activation of the site. Let’s see….yes…here you go:
      https://qrper.com/2021/04/completing-a-field-activation-when-band-conditions-are-poor/

      🙂 Just check out the video link in that post (warning: it’s a long video!).

      Cheers,
      Thomas

  2. Thomas, I’ve noticed that with the CHA LEFS and the Pactenna you launch them with the balum transformer off the ground whereas with the MFJ 1984LP you launch the antenna with the balum on or near the ground. Is one method better than the other? It got me thinking so this morning I launched my MFJ 1984 hoisted up about 20 feet off the ground. The SWR readings were not any better than mounting the transformer on the ground. I believe using the inverted vee configuration is slightly better using a rope loop to raise the center of the wire to the highest point. Any thoughts?

    1. Karen, I think it was roughly N by NW. It’s hard for me to confirm at the moment because (sadly) my Internet is so slow I can’t get the Google Earth view to properly load! I’ll try later.

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.