Skip recommends the QRPguys DS-1 portable antenna kit!

Many thanks to Skip (K4EAK) who shares the following guest post:


The QRPguys DS-1 Portable Antenna Kit

by Skip (K4EAK)

There have been several videos and extended comments lately about the Elecraft AX1 and AX2 antennas, both of which function remarkably well for a small, highly compromised antenna.

For those interested in other, similar designs, especially those hams who find that building the equipment is half the fun, another option to consider is the QRPguys DS-1 antenna.

The DS-1 is similar in concept and design to the AX2. It consists of a base-loading coil, a 46.5-inch collapsible whip, and a plate to attach the antenna to a small tripod. One can also purchase an add-on 40-meter coil. The can be deployed in just a couple minutes and, when collapsed, the longest portion is only 6.5” long, easily fitting in the palm of one’s hand. QRPguys recommends a 16.5′ counterpoise; I use two such wires, usually spread out at a 180-degree angle. I’ve also used it with a clamp-on mount and a car window mount.

Building the antenna is simple and took me less than an hour. After installing a BNC connector into a brass plug and inserting the plug onto a length of PEX tubing, one simply runs the supplied 22AWG wire from inside the tubing, out and around making 22 turns, and then sealing it with a length of heat shrink tubing.

There are really only two aspects of assembly that are slightly more difficult. The first is that it’s necessary to drill and tap two holes for 4-40 screws, which obviously means that (1) one needs a 4-40 tap and (2) one needs to be careful tapping the threads to assure a clean cut. The second is that the heat shrink tubing, at least as supplied in my kit, was grossly oversized, which required some finesse in getting a final product that was at least reasonably aesthetic, to say nothing of accomplishing that without dry roasting my fingertips.

Field testing of the DS-1 shows that it works surprisingly well. The SWR is well below 2.0 across almost all of the 20-meter band and where it is higher than that (the upper end of the voice portion), the KX2 internal tuner can tune it easily. As one would expect, on 40 meters the antenna has a somewhat narrower range, although the KX2 tuner has handled it on all of the frequencies I’ve tested so far (all CW). And it appears to be efficient enough.

I have used it on numerous activations and consistently get to the requisite 10 contacts within 20 minutes or so after getting spotted. After that, the number of contacts depends on the time available, but for those occasions when I have only a 30-minute window for an activation, the antenna is a convenient and practical alternative.

I keep the antenna, the tabletop tripod, and the counterpoise wires in the water bottle pocket of my pack, ready for use whenever I have a few moments for a quick activation.

73 Skip K4EAK

Click here to check out the QRPguys DS-1 antenna

LnR Precision taking orders for the next batch of MTR-4Bs

Many thanks to Jim (N9EET) who notes that LnR Precision is now taking orders for the next batch of the Mountain Topper MTR-4B V2.3.

LnR notes the following on the MTR-4B order page:

Update: 2/24/22: MTR4 V2.3 online ordering is now active! We are releasing 100 units and they will be available as first come, first served. We have a handful of units built now but are expected to quickly have a 3-4 week lead-time before they ship. This could be LONGER and we can’t guarantee shipment in that timeframe but will do our best. We have enough parts in hand for 250 units so there will be another release of this model once we have shipped the first 100.

Also, the MTR4b pricing was increased slightly (up $20) to cover part cost increases. The overall costs were much higher but we know how bad overall inflation has been so we want to be as reasonable as humanly possible. Thanks so much for your continued patience and we know you will enjoy this radio!

This is great news for those of you who have been wanting to reserve an MTR-4B.

If you’re on the fence about ordering one, consider checking out my full review here.

Click here to check out details on the  MTR-4B order page.

Thanks for the tip, Jim!

Pairing the Elecraft K2 with the AX1 at Tuttle for some QRP P2P DX!

If you recall from my last field report, I’ve been pairing the Elecraft AX1 antenna with a number of radios. For me, it’s been a fun exercise because I always enjoy seeing what sort of results the AX1 might produce. So far, it has never disappointed.

On Thursday, February 2, 2023, I packed two radios in my car with the idea of fitting in two consecutive park activations.

At my first activation of the day–Lake James State Park–I paired the AX1 with my Mission RGO One transceiver. The activation was a blast! Not only did I stay busy working stations, but I also managed a little QRP DX thanks to a hunter from Italy.

K2 and AX1 Under Shelter

Little Guatemala Café

After grabbing a curried chicken salad wrap at Food Matters and a coffee at Little Guatemala roasters in Morganton, I hit my second and final park of the day: Tuttle Educational State Forest (K-4861). It was rainy, so the park was empty which allowed me to take over the very large picnic shelter at Tuttle.

Even though this particular shelter is in a bit of a dip in the land and has a large metal roof, I’ve had successful activations there in the past employing the AX1 antenna.

My hope was that history would repeat itself!

Setting Up

Attaching the AX1 antenna to the back of the Elecraft K2 was not complicated because the K2 has a BNC connector with nothing protruding to get in the way of the Bipod. Continue reading Pairing the Elecraft K2 with the AX1 at Tuttle for some QRP P2P DX!

Elecraft AX1 Test Using American Radio Supply AM-801 Window Mount

Many thanks to Conrad (N2YCH) who shares the following field report:


AX1 Test using American Radio Supply AM-801 Window Mount: POTA Activation at Stuart B. McKinney Wildlife Refuge, K-0228

February 19, 2023

By: Conrad Trautmann (N2YCH)

If you’ve been reading the posts here on QRPer.com lately, you probably already know that the Elecraft AX1 has proven to be an excellent antenna for POTA activations for CW, SSB and Digital modes.

Personally, I used it for a New York City POTA rove I did at the end of 2022 and was able to activate four parks in one day all over Manhattan.

Recently, Alan, W2AEW contributed a story to QRPer.com detailing how he used a window bracket he constructed with an AX1 to do a CW park activation from his car. I’ve actually done a few digital activations from the car using the AX1, however, I used the tripod with the Elecraft tripod adapter and ran coax to it out the window and draped the counterpoise down the hood or trunk. This has worked well except for windy days where it would blow over. I was intrigued by the possibility of using the window mount and a number of the commenters to Alan’s post suggested sources for these types of mounts. I ended up ordering an AM-801 from American Radio Supply.

https://www.americanradiosupply.com/am-801-window-antenna-mount-bnc-connectors/

Since the AX1 depends on a counterpoise wire to operate properly, the first thing I did after receiving the AM-801 mount was to drill a hole in the base for a screw and a wing nut. The base is painted black, so I got my continuity meter out to double check that the screw was making a good ground, which it was. I had to bend the mount up slightly for the antenna to be vertical, since my Jeep windows don’t have much of an angle to them. I’m sure it would be just right for most cars.

My next step was to give it a try. Continue reading Elecraft AX1 Test Using American Radio Supply AM-801 Window Mount

Notes from new Elecraft AX1/AX2 owners

After posting my latest field reports using the Elecraft AX1 antenna, I’ve received a number of messages from new AX1 owners. All of the following have kindly allowed me to share them here with you.


AX1 Patio DXing

From Michael (K1ETA):

Thomas,

I am a subscriber and an avid follower. [L]ike you, I do a lot of portable ops with various antenna setups and radios. I was recently offered an AX1 and I was told it was basically a dummy load. Having seen your videos and proof of success I accepted it and I can’t say how much fun I have with it. Yesterday, I made 22 DX contacts throughout Europe in the ARRL World Wide CW contest from my patio in my back yard with 5 watts, the AX1 and my KX2.

I would never have tried that with the AX1 had I not seen your videos. You see it is even good enough for contests if you don’t try to compete with the big guns. Listen, search and call back the stations without pileups!

Many thank for all you do and for making me an AX1 believer.

72

Michael Kenney (K1ETA)


Pairing the AX2 and Emtech ZM-2

From Michael (N7CCD):

Hi Thomas,

I just finished your video comparing the AX1 and AX2 and thought you might appreciate a solution I came up with for making my travel more compact.

I purchased the AX2 during the February sale and found it pairs well with the ZM-2 ATU for my IC-705 (wow what a mouthful of acronyms. No wonder my wife and daughter call me a nerd…). I didn’t get the tripod adapter in the sale, but found the AX2 sits perfectly on the ZM-2 which acts as a very stable stand. There is some body capacitance when tuning, but not too much. I was even able to easily tune it on 17M. I need to try other higher bands sometime.

I set it up in our breakfast nook just for kicks and sent a few JS8 and FT8 transmissions to see where I was being heard (I’ll include a screenshot). Was able to successfully send an APRS text message, and I even made an SSB contact into a special event station in Nevada!

I found a hard sided case I can store the tuner and AX2 in, which also had enough room to put in a “speaker wire” antenna as an option. Why not?

I think this may replace the AlexLoop for air travel since it’s so compact and versatile.

Hope all is well on your side of the country!

Michael – N7CCD

P.S. +16 into Michigan!


AX1 DXing

From Kevin (KD8IE):

Hi Tom,

After video about the AX1 recently, I decided to order one and it came last week.

The weather’s been kind of chilly up here. As a matter of fact, it was 41 when I decided to go out and do an activation then at Cuyahoga Valley National Park.

Well, suffice to say I made contacts with the antenna a lot farther than I expected it would be. The bands were really long. First station I worked was in New Brunswick. The last two stations were Italy and Slovenia.

73,
KD8IE


Many thanks to all of you for sharing your experience and tips using the AX series antennas!

As a reminder, Elecraft has a February promotion on an AX1 and AX2 packages that includes free shipping. There are a few days of this promotion left at time of posting.

Jim’s “WD-PT-PB” AX1/AX2 table/bench clamp mount


Many thanks to Jim (N9EET) who writes:

Thomas:

I look forward to all your videos and am enjoying how you use the Elecraft AX-1 in the field.

I have built the “WD-PT-PB” attachment for my AX-1 antenna.

That is, it is for Windy Day-Picnic Table-Park Bench use. It can be set up horizontally or vertically on the edge of a picnic table or at any angle on the back of a park bench and is a secure attachment for the AX-1 off the radio.

[I] bought the bolts straight and put them thru a random C clamp secured with a nut or wing nut and then bent one in my vise. Loosen the wing nut and angle the bolt any way I want and tighten the wing nut.

The pictures show it better than paragraphs of a description.

73,
Jim Long
Madison, WI
N9EET

That’s brilliant, Jim! I love how versatile the clamp is and that it even fits in your Maxpedition pouch! No doubt, it’ll help the AX1 (or AX2, or any similar antenna) survive the windiest of deployments.

Thank you for sharing.

Postcard Field Report: Pairing the Mission RGO One with the Elecraft AX1 at Lake James for some QRP DX

Welcome to my first Postcard Field Report!

If you’ve been following QRPer.com and my YouTube channel for long, you’ll notice that I typically post two field reports with videos per week when my free time allows. Each report takes about four hours to produce along with a video. I’ve currently got a small backlog of videos I need to post, so in order to squeeze them into my schedule, I’m going to use a slightly more abbreviated field report format: a “postcard” format!

My Postcard Field Reports will still be information-packed, just slightly more concise and distilled than my average field report. I’ll primarily post these for sites I visit frequently.

Speaking of which….

Lake James State Park (K-2739)

Thursday, February 2, 2023, was a rainy, dreary day so the perfect time to play a little POTA, right?  I made time in my morning to visit Lake James State Park (K-2739).

When I arrived at the Catawba River Access, the parking lot was empty. Not too surprising considering it was a Thursday morning on a chilly, rainy day.

Of course, I had the picnic shelter all to myself, so why not use it to stay dry? Continue reading Postcard Field Report: Pairing the Mission RGO One with the Elecraft AX1 at Lake James for some QRP DX

Video: What are the differences between the Elecraft AX1 and AX2? Should you buy one?

The Elecraft AX1 paired with the KX2.

During the months of January and February 2023, I’ve given my Elecraft AX1 a thorough workout. As I mentioned in a previous post, I thought it might be fun to take the AX1 out on a good 30 days worth of activations.

Turns out, I’ve had such brief windows of opportunity to play radio recently, the AX1 and now AX2 have been valuable tools in my field kit. They are, no doubt, the quickest-to-deploy and most portable antennas in my collection.

The Elecraft AX2 paired with the KX2.

If I only have a 20 minute window to squeeze in a quick park activation, the AX1 and AX2 make a valid POTA activation–with 10 logged contacts– a reality.

I originally purchased my Elecraft AX1 in the spring of 2020 and have used it extensively since then. In January 2023, I finally caved in and purchased the most recent addition to the AX family, the mono-band AX2.

Elecraft AX1 vs. AX2

Since I’ve been publishing numerous field reports recently using the AX1 (with more to come) and since Elecraft has included both the AX1 and AX2 in their February 2023 Specials, I’ve received questions from readers asking:

  1. “Should I buy an AX1 or AX2–?”
  2. and “If so, which one should I buy? What are the differences?”

At first, I simply pointed readers to the concise comparison guide that Elecraft publishes on their website (linked below).

I realize, though, that there are characteristics of each antenna that you might only discover after actually using them in the field.

I decided to make am unedited video–based on a few notes–not only describing the differences and similarities of the AX1 and AX2, but also if either would potentially benefit you as a field operator or traveler.

One quick note about resonance…

One point I touch on in the video is that both the AX1 and AX2 antennas are designed to be mostly resonant on 20 meters.

Small verticals like the AX1 and AX2, that use coils to electrically “lengthen” the antenna, have a higher Q than, say, a large aperture quarter or half wave antenna. In practical terms, this means that the window of resonance is narrow and more fickle than, for example, an end-fed half-wave.

A lot of factors can affect the SWR on higher-Q antennas like the AX1/AX2 including:

  • the type of terrain,
  • height off the ground,
  • length of counterpoise,
  • configuration of counterpoise,
  • and, most notably, the operator’s own body capacitance.

You may find that the AX2, for example, is natively resonant on 20 meters at one location, but isn’t at another location. This is quite normal. It’s also the reason why Elecraft states that both antennas are designed to be used with an ATU.

If you are pairing the AX1 or AX2 with a radio that doesn’t have an ATU (or you can’t use an external one), then you might consider making a simple capacity hat. Check out this field report and video where I paired the AX1 with the IC-705 and used a capacity hat to sort out the SWR.

Video

As with all of my videos, this one is unedited and commercial-free. If you’d like to skip through the video to the parts you might find most relevant, simply hover your mouse over the YouTube time line and click on the chapter indicated:

Click here to view on YouTube.

Another note here: I have no affiliation with Elecraft, but pushed this article and video to the front of the line to help those who are consider taking advantage of Elecraft’s  AX1/AX2 February 2023 Package Deals.

I hope you find the video helpful. I’ll try to answer any other questions you might have in the comments of this post.

Resources

Thank you

I hope you enjoyed this comparison video.

I’d also like to send a special thanks to those of you who have been supporting the site and channel through Patreon and the Coffee Fund. While certainly not a requirement as my content will always be free, I really appreciate the support.

Cheers & 72,

Thomas (K4SWL)

Elecraft’s KX2 Internal Battery Charger with RTC, the KXIBC2, is now shipping

Elecraft KX2 owners that follow Elecraft’s email discussion groups have heard that the new KX2 internal battery charger, the KXIBC2, has been tested and would soon be available for purchase.

I checked the Elecraft website this morning and the KXIBC2 has been added to the KX2 product page within the past 12 hours or so.

There are two model numbers:

  • KXIBC2-F: The “F” in the model number indicates that it will be factory installed with a new KX2 order.
  • KXIBC2: This is the part you would order if you already own a KX2 and plan to install it yourself. This one is referred to as the “Kit” version since the user installs it.

The price is $139.95 US plus shipping.

I just ordered the Kit version and paid a total of $149.30 US with shipping.

According to Elecraft, the kit version is actually very simple to install, but there’s an option to have the factory install it for you via an RMA. Elecraft notes:

Anyone with a modest amount of soldering experience should be able to do the KXIBC2 installation. Based on lots of feedback from field testers, we dramatically simplified the installation procedure. For field installation, we recommend “Method 1” (see the revision B2 instruction manual or later). There’s no need to do any disassembly other than removing and replacing the right side panel. And there are only two wires to solder. If after having a look at the instructions you feel that you’d rather let Elecraft to the job, we’ll be happy to. Simply contact [email protected] to obtain an RMA.

I’ve been looking forward to this particular KX2 upgrade.

While I don’t find removing the internal battery, charging it, then replacing it very cumbersome–I’ve literally done this hundreds of times–the new internal charger will make topping off the battery that much easier.

The KXIBC2 replaces the previous KXIO2 Real-Time-Clock optional module. If you have the KXIO2 installed, you’ll need to remove it and replace it with the KXIBC2.

The KXIBC2 retains the RTC (real-time-clock) function.

For more information about the KXIBC2 module, check out the product manual and installation guide here (PDF).

HRCC Livestream Saturday, February 18, 2023: We’re talking packs & bags!

Josh (KI6NAZ) over at Ham Radio Crash Course has (in what must have been a momentary lapse in judgement) invited me back on his Saturday Night Live Stream to talk packs, bags, and radios.

Of course, this being one of my favorite topics, I’m looking forward to it. That and Josh is a great host.

The live stream starts at 5:00PM PST/8:00PM EST on Saturday, February 18, 2023.

Click here to bookmark it.

QRP radios, product announcements, reviews, news and more. Low power amateur radio fun!