Category Archives: News

Part 2: N2YCH and K1PCN’s Dayton Hamvention Trip QRP POTA Rove

Many thanks to Conrad (N2YCH) who shares the first of a three-part field report series outlining his 2023 Hamvention rove with Peter (K1PCN). Click here for Part 1, and look for Part 3 next week!


Part 2: Dayton Hamvention Trip QRP POTA Rove

By Conrad Trautmann, N2YCH

Pennsylvania

Welcome to part two of three of the Hamvention QRP POTA Rove. If you missed part one, you can find that installment here.

Early on Thursday morning, May 18, 2023, Peter, K1PCN and I headed from Morgantown, West Virginia north to Pennsylvania to activate K-8920, the PA 223, Pennsylvania State Game Lands. While the park covered a large geographical area, we were able to find a parking lot not far off the highway that made it easy for us to get to and activate.

Peter spotted a nearby gazebo which was also a viewing area and hiked over to it to activate. If you look closely in the photo below, you can see it in the distance behind the sign and my antenna.  I stayed with the Jeep and set up on the tailgate using the Buddipole vertical.

Since it was early in the day, we used our frequency strategy of Peter on 40 meters and me on 20 meters. My QSO map here shows some decent DX for QRP on 20 meters at 8am ET.

Ohio

We traveled North towards Pittsburgh on Interstate 79 and then West on Interstate 70, passing through West Virginia again and then stopped at K-1934, Barkcamp State Park in Ohio.

I tuned my antenna for 17 meters and Peter activated on 20 meters.

I managed to activate the park, but it was slow going for me on 17, so when Peter finished up on 20, I changed to 20 meters and got a few more on that band just for good measure. Thinking that the slow QSO’s could have been the radio, I did switch to the IC-705 here, but that did not make any difference. It could have been conditions or our location. I did have better luck on 20 meters than 17. And I don’t know about you, but I can never go for just ten QSO’s. I feel like I need a few extra ones just in case. Here is a photo of me set up at a picnic table next to my antenna. Continue reading Part 2: N2YCH and K1PCN’s Dayton Hamvention Trip QRP POTA Rove

This seven hour road trip calls for a QRP POTA break at Yatesville Lake State Park!

On Tuesday, May 23, 2023, I had one main goal in mind: drive from my buddy Eric’s QTH in Athens, Ohio, back to my QTH in Swannanoa, NC.

This was the final leg of my one week Hamvention journey and I was ready to get back home and rest up before yet another road and camping trip only a few days later.

Before leaving WD8RIF’s QTH that morning, I consulted him about possible POTA sites I could easily activate on my journey.

On the return trip, I chose to drive through Ohio, West Virginia, Kentucky, Virginia, Tennessee, then North Carolina.

Eric knows regional parks very well because he’s activated nearly all of them. He suggested Yatesville Lake State Park as it was an easy detour off of Highway 23 in Louisa, Kentucky.

Before leaving Eric’s house, I scheduled the activation and put the address in my car’s GPS/Sat Nav.

Yatesville Lake State Park (K-1272)

I arrived at the Yatesville Lake around 10:45 AM EDT and drove to the campground entrance where I met the campground host. I introduced myself and told her I was looking for a picnic spot to do a POTA activation (explaining to her, of course, what POTA is).

She couldn’t have been more helpful. She pointed out a roadside picnic spot beside us at the campground entrance, she also noted some covered picnic shelters nearby (that seemed to be in use), and even told me I could drive into the campground, find an empty camping spot and just set up there! A very generous offer, but I opted for the roadside picnic table next to me at the campground entrance since I was already parked in the right spot.

There wasn’t much to this particular site; just a picnic table and corn hole game next to the road in full sun. I had my sun gear on (wide brimmed hat and long sleeve lightweight hiking shirt) so the lack of shade wasn’t an issue.

There were plenty of trees on the perimeter of the site, but none would be an easy snag for my throw line because there were no branches overhanging the perimeter. Still, I knew if I launched the throw weight as close as I could to the tree line, I should be able to snag a small branch without having to search in the woods for the end of the line.

As long as I could suspend my mostly homemade 40 meter end-fed half-wave, I’d be a happy activator. Continue reading This seven hour road trip calls for a QRP POTA break at Yatesville Lake State Park!

A New Skill and Antenna Leads to Success at Wormsloe K-3725

Many thanks to Teri (KO4WFP) for the following guest post:


A New Skill and Antenna Leads to Success at Wormsloe K-3725

by Teri (KO4WFP)

If you read my field report for Wheeler NWR K-0161, the trap dipole I used vastly outperformed the AX1 that particular day. I originally opted for the AX1 because, for my upcoming trip to Nova Scotia, my family and I will fly so space for ham equipment is limited. But the Wheeler activation convinced me to add an end-fed antenna to my kit for the trip, something several hams recommended. I chose the Tufteln EFRW QRP antenna.

Ham radio has taught me many things, one of them being I tend to procrastinate when I feel intimidated by a project. Case in point – the Pacific Antenna 2040 trap dipole I used in my last activation. My local radio club recommended it for POTA. (They were correct by the way – that antenna works well!) The project sat on my shelf for nine months before I got up the courage to work on it.

The same thing happened when I ordered a Morserino kit. I knew it would be a great learning opportunity due to my limited experience with electronics. Well, it took me three months to get up the courage to tackle that project. So, for whatever reason, getting antennas into trees fell into the same category in my mind. Now, having to use an end-fed antenna for POTA, I needed to learn the skill but had no idea where to begin.

Thankfully Thomas came to the rescue! I found his July 3rd, 2022 post discussing the various iterations of throwing equipment he used and on what he settled. Soon I acquired a Weaver 10 oz. weight, a spool of Marlow 2mm throw line, and a Tom Bihn small travel tray.

I next found Thomas’ Sept. 8th, 2020 post as to how to prepare the line (you tie it to a tree and tug hard on it several times to remove any kinks in the line), flake the line into a cube or bag, tie a slip knot to attach the weight, and then use one of two techniques for launching the line over a branch.

In my HOA, there is a wooded area that offered privacy and the perfect live oak branch, about 15 feet high, for my initial practice session. I opted for what is called the “granny toss”. Heck, if it was good enough for the arborist whose video Thomas featured in his September 8th post, it was good enough for me, no matter how ridiculous it might look. And guess what? Success on the third throw! OK. This skill was not proving to be nearly as daunting as I had assumed.

Now it was time to put this newly-acquired skill to use. Tuesday June 13th, I chose to return to Butter Bean Beach at Wormsloe (K-3725), partially to further my kilo pursuit for this park but also because I knew hams from my local club had used end-fed antennas there.

The drive to Butter Bean Beach from my home is a favorite. I take Ferguson Avenue which has a live oak canopy stretched over the road. The trees are dripping with Spanish moss and look like old Grand Dames swathed in grey boas.

Along the road is Bethesda Academy which used to be an orphanage for boys. The institution was established in 1740 by evangelist George Whitefield. Today Bethesda is a private boarding and day school for boys. The academy has a dairy and I often slow down to look at the cows with their calves in the pastures. You never know what you might see – I’ve actually pulled over to watch a newborn calf take its first steps. (How cool is that!) Today the cows and their calves were lounging in the afternoon shade of one of those Grand Dames. Continue reading A New Skill and Antenna Leads to Success at Wormsloe K-3725

Beating the POTA propagation blues at Stonelick State Park!

As mentioned in my previous POTA field report, I had the great pleasure of playing POTA on May 21, 2023 with a number of friends. We all played hooky on the final day of Hamvention. The first two activations of the day were with Vince (VE6LK/AI7LK), Charlie (NJ7V), Eric (WD8RIF), and Miles (KD8KNC).

Charlie and Vince had to leave us after the second activation of the day because both of them had travels in store that afternoon.

Eric, Miles, and I grabbed lunch at a nearby town, then made our way to our final park of the day.

Stonelick State Park (K-1993)

We pulled into Stonelick State Park a little after 3:00 PM and found the best open area to set up our stations. This park was a new one for me and, I believe, for Eric as well. (FYI: Miles didn’t hop on the air that day, but helped his dad set up his POTA station.)

Eric’s station

Eric set up his station on a bench overlooking Stonelick Lake. He supported his 28.5 foot vertical wire antenna on a 31′ Jackite fiberglass telescoping pole which he strapped to the bench. His transceiver of choice was the Elecraft KX3.

Note that Eric writes detailed field reports for all of his activations and field activities on his website.

For more details on this activation from Eric’s perspective, click here!

Working with poor propagation

Instead of using a vertical, I opted to deploy my recently cannibalized 40 meter end-fed half-wave. I felt a full 40M EFHW, properly deployed, would increase my chances of logging stations on a day where contacts were few and far between. Continue reading Beating the POTA propagation blues at Stonelick State Park!

Part 1: N2YCH and K1PCN’s Dayton Hamvention Trip QRP POTA Rove

Many thanks to Conrad (N2YCH) who shares the first of a three-part field report series outlining his 2023 Hamvention rove with Peter (K1PCN). Look for Part 2 next week!


Part 1: Dayton Hamvention Trip QRP POTA Rove

By Conrad Trautmann, N2YCH

Peter, K1PCN and I are both avid Parks On The Air activators here in Connecticut and neither of us has ever been to the Dayton Hamvention in Xenia, Ohio. At the urging of others who have attended in the past, we made the decision to attend this year and while we were making the trek out, we wanted to activate parks along the way to add to our activated US states award. We originally planned to activate six states and ended up with one bonus state for a total of seven. This is how things looked before and after the trip.

 

I would like to begin by saying that attending the Hamvention was a great experience. If you have not been to it, I would like to encourage you to attend if you can.

You may have heard about the flea market, the vendor booths, the forum sessions or the food trucks, which are all good, but the best part for me was being in the presence of other hams with similar interests. I struck up conversations and shared stories with many other hams. Everyone was very nice and willing to share their experiences, which is a great way to pick up some good tips.

I am extremely glad I went. If you are on the fence about going, I would recommend you plan to go next year. Oh, and I got to meet this guy in person….

Now on to the rove…

I planned the trip to get as many states as possible. Both Peter and I had already activated CT, NY and NJ, so we did not need to stop in those states as we passed through. I had scoped out some parks near the Delaware and Maryland border, so I looked at those first.

My main criteria on park selection was to pick parks that would be easy-off/easy-on to the main highways we would be traveling to save time on driving. Here is the route map we followed.

We strategized on how we would activate the parks when we got to each one. Peter is an SSB activator, and I am a digital activator. We would not be colliding on the mode of operation. We did need to be on different frequencies though.

In the mornings, Peter took 40 meters and I used 20 meters. Later in the day when the bands opened up, Peter moved up to 20 meters and I bumped up to 17 or 15 meters. Using this strategy, we had no problems getting our minimum ten QSO’s to activate while operating at the same time. Peter also reminded me to bring a handheld and we did park to park QSO’s on 2 meters and 70cm.

As for equipment, I used my Elecraft KX3 transceiver, but I did bring an IC-705 as a backup.

On the first stop in Delaware, I used an Elecraft AX1 antenna but for the rest of the trip I used a Buddipole tripod equipped with a Versa-T with a 17’ MFJ whip tuned to the frequency I was operating on with 50’ cable and an above the ground counterpoise. Continue reading Part 1: N2YCH and K1PCN’s Dayton Hamvention Trip QRP POTA Rove

KO4WFP: The Dipole Does It for Wheeler NWR

Many thanks to Teri (KO4WFP) for the following guest post:


The Dipole Does It for Wheeler NWR (K-0161)

by Teri (KO4WFP) 

After my last activation, I was hankering to try the AX1 and Pacific Antenna 2040 trap dipole during the same activation for a comparison. Now, I know some of you are saying, “Well Teri, there would be no contest!” Yes, however, in the interest of learning first-hand, I headed to K-0161, Wheeler National Wildlife Refuge while visiting a friend, Glenn W4YES, and his wife in Decatur, Alabama.

Wheeler National Wildlife Refuge was established in 1938 as a wintering area for ducks, geese, and other migratory birds. It is a 35,000 acre refuge located along the Tennessee River near Decatur, Alabama. Today, the refuge attracts thousands of wintering waterfowl and cranes each year and is a winter home to the endangered whooping crane who first arrived in 2004.

I opted to set up in a parking lot on the north side of US Highway 67 which runs through a small portion of the refuge. As there were no picnic tables present, I chose a spot where the trees would shade me from the early morning sun while sitting in my Subaru Crosstrek. Since the last activation, I had given some thought as to how to set up better in the car. My code buddy Caryn KD2GUT sits in the backseat for POTA with one seat flipped down providing a ready-made table for equipment. Even better, I discovered the back of the rear seat in the Crosstrek has a rubber surface and I could secure the key to it with fun-tak!

Since the last activation, the more I worked with the Mini Palm Paddle, the more I realized I did not like it. It just felt too “squishy” for my taste and I had difficulty feeling the characters. Glenn has a solid state CW paddle by 9A5N he was not using. I worked with it a bit and really liked the stiffer feel. He removed the heavy base in which it was mounted and built a lighter base out of the back of a old diskette so I could take the key with me to Nova Scotia. (True ham radio – making use of whatever we have on hand to solve a problem!) I find the more I use this key, the more I like the feel of it.

This was Glenn’s first POTA activation and I was happy to have him along. We arrived around 8:05 AM and began setting up, first putting the AX1 on the roof of the car and then the trap dipole on a mast on a hitch mount given to me by Jack NW4TF of my local club. Continue reading KO4WFP: The Dipole Does It for Wheeler NWR

QRP POTA with Friends: Two Park Activations with VE6LK, NJ7V, WD8RIF, and KD8KNC!

Sunday, May 21, 2023, was the final day of Hamvention.

I traveled to Hamvention with my buddies Eric (WD8RIF) and his son Miles (KD8KNC). We decided in advance that instead of attending Hamvention that Sunday (after having spent all day Friday and Saturday there) we’d opt for a relaxing day playing POTA near Dayton/Xenia.

We weren’t, in fact, the only ones who skipped Hamvention that Sunday–our friends Vince (VE6LK or AI7LK State-side) and Charlie (NJ7V) did as well, so we decided to play POTA together!

Both Charlie and Vince were leaving the Dayton area that afternoon, so they needed to finish up their activations by noon at the latest. We decided we could fit in two activations that morning before Charlie and Vince headed back, then Eric, Miles, and I would hit a third park in the afternoon. Actually, Miles never planned to hop on the air, but he was both our ride and valuable POTA support!

Vince and Charlie in the rear view mirror!

Charlie and Vince met us at our hotel around 9:00 AM and we drove to the first of two parks we’d activate together.

Cowan Lake State Park (K-1943)

Charlie (NJ7V) and Vince (VE6LK/AI7LK) ready to deploy their gear.

The weather was beautiful that day, but the space weather, much less so. We knew in advance that it would be a struggle based on the propagation forecast and numerous reports from other activators.

Vince set up his Elecraft KX3-based station in the trunk/boot of his rental car.

He deployed his “low-slung” wire antenna (read more about that here) and hit the air.

Vince’s low-slung antenna

Eric described the POTA station he deployed in his field report on WD8RIF.com:

Eric found a shady, level spot near the parking lot, strapped his 31′ Jackite telescoping fiberglass pole to his folding camp-chair, deployed his 28½’ wire vertical on the pole, set up his Elecraft KX3 on the camp-chair’s flip-up table, and was on the air at 1412 UTC. Eric began his operation with a lovely touch-paddle which he had unexpectedly been given as a gift from the builder, Brian Manley, K3ES

Eric’s station

Note that Eric carefully documents each and every one of his field activations and field contests on his website. His field reports date back to Field Day in 1995!

I found a spot to set up next to the lake under the shade of a large tree. I deployed my Tufteln no-transformer 28.5 foot end-fed random wire.  This antenna is simply two lengths of 28.5′ wire: one wire for the radiator and one for the counterpoise. The KX2’s internal ATU does all of the heavy lifting. Continue reading QRP POTA with Friends: Two Park Activations with VE6LK, NJ7V, WD8RIF, and KD8KNC!

An in-depth review of the Xiegu G106 QRP HF transceiver

Note that the following review first appeared in the May 2023 issue of TheSpectrum Monitor magazine.

Update: Also, please note that the G106 is on sale at Radioddity at time of posting. With our affiliate link pricing is only $264 US (see note at end of review). Please read this review prior to making a purchase decision!


An in-depth review of the Xiegu G106 QRP HF transceiver

by Thomas (K4SWL)

Last year––in May of 2022, that is––Xiegu announced a new compact field radio that would be added to their line of transceivers: the Xiegu G106.

Xiegu has really made a name for themselves over the past few years with several transceiver offerings, many of which have become very popular. Among these:

  • The Xiegu G90 is a 20-watt transceiver with an excellent built-in ATU. The G90 has become a very popular field radio over the past few years.
  • The Xiegu X5101 is a five-watt shack-in-a-box HF transceiver covering 160-6 meters. The X5105 has become a go-to QRP portable due to its fine built-in ATU and built-in rechargeable battery pack.
  • The Xiegu X6100 is much like the X5105, in that it’s also a shack-in-a-box QRP transceiver, but it leverages SDR technology to provide a beautiful color spectrum display and a host of features not found on its predecessors. Many have adopted the X6100 because its operating system is Linux-based and many enthusiasts have created their own X6100 interface that promised direct digital mode operation.

Because we’re seeing more products like these from Xiegu, the up-and-coming Xiegu G106 stirred interest.

Moreover, Xiegu has become a low-cost leader among HF transceiver manufacturers. In each of the reviews I’ve published about Xiegu radios, my summary statement is that each unit offers a lot of performance for the price. Xiegu transceivers don’t have the most robust receiver front-ends, and the audio is unrefined, but their rigs get the job done and have some serious “fun factor.”

So when I first learned about the new Xiegu G106, I was curious where it would fit into their product line.

Introducing the Xiegu G106

As I was capping off my summer in Canada back in August of 2022, Xiegu retailer Radioddity started shipping the G106. Radioddity had me on the list to send a loaner G106 for review, but  upon my return I found myself so busy that I didn’t immediately request it.

I did watch, however, K8MRD’s initial and updated review of the G106 on YouTube. While it was less than stellar––understatement alert––more relevant to me was that Mike shipped his second evaluation unit to me on behalf of Radioddity.

I connected that G106 to a dummy load, checked the transmitted signal on my SDRplay RSPdx spectrum display, and it simply didn’t look very clean. In fact, it looked worse than it did when Mike checked it only a couple of weeks prior.

I shared my results with Radioddity and told them I didn’t feel comfortable putting the G106 on the air; they asked that the unit be returned and checked out.

Fast-forward to January 2023, when I was once again contacted by Radioddity to see if I would like to field test an updated G106? I answered that I was happy to do so, because I was curious whether the G106 experience had improved.

In the spirit of full disclosure, keep in mind that Radioddity is a Xiegu retailer/distributor––the company is not the manufacturer, nor is it owned by Xiegu. They sent this G106 to me on an extended loan for an honest evaluation.

So where does the G106 fit into the Xiegu product line?  It’s being marketed as a low-cost, entry level, multi-mode QRP HF transceiver that leverages 16-bit CODEC sampling to provide the user with a lot of radio for the price. It’s basic, and meant to be so, in that  it’s only a transceiver; there is no built-in ATU or battery. The G106 is marketed as a bare-bones portable HF transceiver.

I feel like it hits this mark.

The G106 doesn’t have a lot of features or controls one might expect in other Xiegu radios, but it has more features than any other modern HF radio I know of in its price class (see features list below). Indeed, I can’t think of any other 80-10 meter general coverage QRP transceiver that retails for $320 or less. The G106 has this market niche to itself for the moment.

Overview

When I first received the G106, I was a little surprised:  it was even more compact than I had imagined.

The sides of the G106 are rounded and the chassis extends beyond the encoder and front controls of the radio, thus the interior is quite well protected in the event the radio is dropped. This is one of the few QRP field radios on the market that doesn’t need an aftermarket cage. I’ve been transporting the G106 in an old hard shell headphone case a friend gave me. The case isn’t large, but it easily holds the G106 and a power cord with a bit of room to spare.

 

The G106 sports a small monochrome backlit display that’s very easy to read in the shack or in the field with full sunlight.

Besides the weighted encoder (which has soft detents), the volume control, and microphone port, there are also four multi-function buttons located under the small display on the front panel. On top of the radio, there is a power/backlight button, mode/pre-amp button, and two band buttons that also can be pressed and held to change the frequency cursor position. The internal speaker is also mounted on the bottom of the top cover, just behind the top panel buttons.

On the back of the G106, you’ll find a BNC antenna port, ground/earth lug, key port, COM port, 8 pin ACC port, and a DC input port.

The most conspicuous omission is a headphone or external speaker port. I would have expected this in a QRP field radio because operators often prefer using headphones in the field rather than a speaker. I know that some G106 owners have built their own RJ9 audio plug to port out the audio to headphones. There is a headphone port on the supplied speaker mic, but CW-only operators might prefer a more direct way to connect earphones in order to keep the bulk of their field kit to a minimum.

What is surprising is that the G106 has a very basic spectrum display that is actually quite useful!

Ergonomics

The ergonomics of the G106 are overall pretty good…but a bit quirky. To be honest, giving the user access to numerous functions and features on a radio this small is always going to affect ergonomics; there’s only so much control-surface real estate. Continue reading An in-depth review of the Xiegu G106 QRP HF transceiver

Tu-Endie-Wei State Park: Low-impact QRP fun and one speedy P2P confirmation!

On Wednesday, May 17, 2023, I did something I hadn’t done since 2019: I woke up, hopped in the car, and started my journey to the Four Days In May and the Dayton Hamvention!

It’s about a seven hour drive from my QTH directly to Dayton, but in the 12+ times I’ve attended Hamvention, I’ve never actually driven there directly. Instead, I drive to Athens, Ohio, spend the evening with my buddy Eric (WD8RIF) and his family, pack one car, then carpool to Dayton.

Heading to Athens, I like to time my drive so that I pass through Beckley, West Virginia around noon and enjoy a fine lunch at Tamarack Marketplace. It’s always a nice reward after spending a little over four hours in the car.

This year, I enjoyed local almond-crusted rainbow trout, braised kale, and dill pickle soup. I know…dill pickle soup sounds a bit strange, but trust me: it was exquisite. The food at Tamarack is always top-shelf because the chefs behind the scenes are training for positions at the famous Greenbriar Resort.

Park en route

Of course, another way to break up the trip and add a little fun is to activate a park. I decided I wanted to activate a new-to-me park not too far off my route, so I consulted the regional POTA expert: WD8RIF.

Eric is an avid park activator and has hit pretty much every park within a three hour drive of his QTH. He made a few suggestions, and I opted for Tu-Endie-Wei State Park in Point Pleasant, West Virginia.

Tu-Endie-Wei State Park (K-1823)

Tu-Endie-Wei is a small, four acre state park, situated at the confluence of the Kanawha and Ohio rivers in Point Pleasant, WV. Indeed, the name “Tu-Endie-Wei” is a Wyandotte word meaning “point between two waters.” Continue reading Tu-Endie-Wei State Park: Low-impact QRP fun and one speedy P2P confirmation!

QRPer Notes: Alan Reviews the FX-4C, Common Mode Chokes, and Kitchener Waterloo ARC Hamfest Tour

Because I receive so many tips from readers here on QRPer, I wanted way to share them in a concise newsletter format.  To that end, welcome to QRPer Notes, a collection of links to interesting stories and tips making waves in the world of radio!


Radio Review: FX-4C SDR QRP Transceiver

Many thanks to Ron who shares this excellent review of the FX-4C by our friend Alan (W2AEW):

Click here to view on YouTube.


Common Mode Chokes

Many thanks to David (WK4DS) who shares the following post about common mode chokes.

Click here to read.


Kitchener Waterloo ARC Hamfest 2023

Many thanks to John (VE3IPS) who shares his quick video tour of the Kitchener Waterloo ARC Hamfest:

Click here to view on YouTube.